Displaying all 18 publications

Abstract:
Sort:
  1. Mohamad NA, Azis N, Jasni J, Ab Kadir MZA, Yunus R, Yaakub Z
    Materials (Basel), 2018 Mar 30;11(4).
    PMID: 29601520 DOI: 10.3390/ma11040532
    This paper presents a sealed ageing study of palm oil (PO) and coconut oil (CO) in the presence of insulation paper. The type of PO under study is refined, bleached, and deodorized palm oil (RBDPO) olein. Three different variations of RBDPO and one sample of CO are aged at temperatures of 90 °C, 110 °C, and 130 °C. The properties of RBDPO and CO as well as paper under ageing are then analysed through dielectric and physicochemical measurements. It is found that the effect of ageing is not significant on the alternating current (AC) breakdown voltages and relative permittivities of RBDPO and CO. There is a slight increment trend of the resistivity for CO, while for all of the RBDPO, the resistivity slightly decreases as the ageing progresses. Only CO shows an apparent reduction of the dielectric dissipation factor. Throughout the ageing time, the acidities of all of the RBDPO and CO remain at low level, while the moisture in oils decreases. The tensile index (TI) of the papers for all of the RBDPO and CO retain more than 50% of the TI. A significant increment of the paper ageing rates of all of the RBDPO and CO is observed at an ageing temperature of 130 °C.
    Matched MeSH terms: Sodium Compounds
  2. Mustafa NS, Yahya MS, Sazelee N, Ali NA, Ismail M
    ACS Omega, 2018 Dec 31;3(12):17100-17107.
    PMID: 31458330 DOI: 10.1021/acsomega.8b02281
    The K2NiF6 catalytic effect on the NaAlH4 dehydrogenation properties was studied in this work. The desorption temperature was studied using temperature-programmed desorption and exhibited a lower onset hydrogen release after doped with different wt % of K2NiF6 (5, 10, 15 and 20 wt %). It was found that the NaAlH4 doped with 5 wt % K2NiF6 showed the optimal value that can reduce the onset desorption temperature of about 160 °C compared to 190 °C for the milled NaAlH4. The NaAlH4 + 5 wt % K2NiF6 sample showed faster desorption kinetics where 1.5 wt % of hydrogen was released in 30 min at 150 °C. In contrast, the milled NaAlH4 only released about 0.2 wt % within the same time and temperature. From the Kissinger analysis, the apparent activation energy was 114.7 kJ/mol for the milled NaAlH4 and 89.9 kJ/mol for the NaAlH4-doped 5 wt % K2NiF6, indicating that the addition of K2NiF6 reduced the activation energy for hydrogen desorption of NaAlH4. It is deduced that the new phases of AlNi, NaF, and KH that were formed in situ during the dehydrogenation process are the key factors for the improvement of dehydrogenation properties of NaAlH4.
    Matched MeSH terms: Sodium Compounds
  3. Dezfouli MG, Eissazadeh S, Zade SM
    Microsc Microanal, 2014 Aug;20(4):1167-79.
    PMID: 24735566 DOI: 10.1017/S1431927614000701
    This study examines histometrical changes induced by sodium arsenite (SA), as an environmental pollutant, and investigates the protective effect of α-tocopherol on ovaries of SA-treated rats during the prenatal stage until sexual maturity. Rats were classified into groups: control, SA (8 ppm/day), α-tocopherol (100 ppm/day), and SA+α-tocopherol. Treatment was performed from pregnancy until maturation when the rats and ovaries were weighed. The Cavalieri method was used to estimate volume of the ovaries, cortex, medulla, and corpus luteum. The mean diameter of oocytes, granulosa cells, and nuclei were measured and volume was estimated using the Nucleator method. The number of oocytes and thickness of the zona pellucida (ZP) were determined using an optical dissector and orthogonal intercept method, respectively. SA reduced the body and ovary weight, the number of secondary, antral and Graafian oocytes, volume of the ovaries, cortex, medulla and corpus luteum, mean diameter and volume of oocytes in primordial and primary follicles, mean diameter and volume of oocyte nuclei in all types of follicles, and mean thickness of the ZP in secondary and antral follicles. Also, the mean diameter and volume of granulosa cells and their nuclei in antral and Graafian follicles decreased significantly. Vacuolization and vascular congestion in the corpus luteum and an increase in the number of atretic oocytes were seen in the SA group. Most of these parameters were unchanged from the control level in the SA+α-tocopherol group. It was concluded that α-tocopherol supplementation reduced the toxic effects of SA exposure on ovarian tissue in rats.
    Matched MeSH terms: Sodium Compounds/antagonists & inhibitors*; Sodium Compounds/toxicity*
  4. Aboud H, Wagiran H, Hussin R, Ali H, Alajerami Y, Saeed MA
    Appl Radiat Isot, 2014 Aug;90:35-9.
    PMID: 24681645 DOI: 10.1016/j.apradiso.2014.01.012
    Characteristics of lithium potassium borate glasses with various copper concentrations are reported. The glasses were prepared by the melt quenching method and irradiated with photons to doses in the 0.5-4.0 Gy range. Glowing curves, dose response curves, reproducibility of the response, dose threshold, thermal fading and optical bleaching were studied.
    Matched MeSH terms: Sodium Compounds
  5. Hilles AH, Abu Amr SS, Hussein RA, El-Sebaie OD, Arafa AI
    J Environ Manage, 2016 Jan 15;166:493-8.
    PMID: 26580899 DOI: 10.1016/j.jenvman.2015.10.051
    A combination of persulfate and hydrogen peroxide (S2O8(2-)/H2O2) was used to oxidizelandfill leachate. The reaction was performed under varying S2O8(2-)/H2O2 ratio (g/g), S2O8(2-)/H2O2 dosages (g/g), pH, and reaction time (minutes), so as to determine the optimum operational conditions. Results indicated that under optimum operational conditions (i.e. 120 min of oxidation using a S2O8(2-)/H2O2 ratio of 1 g/1.47 g at a persulfate and hydrogen peroxide dosage of 5.88 g/50 ml and8.63 g/50 ml respectively, at pH 11) removal of 81% COD and 83% NH3-N was achieved. In addition, the biodegradability (BOD5/COD ratio) of the leachate was improved from 0.09 to 0.17. The results obtained from the combined use of (S2O8(2-)/H2O2) were compared with those obtained with sodium persulfate only, hydrogen peroxide only and sodium persulfate followed by hydrogen peroxide. The combined method (S2O8(2-)/H2O2) achieved higher removal efficiencies for COD and NH3-N compared with the other methods using a single oxidizing agent. Additionally, the study has proved that the combination of S2O8(2-)/H2O2 is more efficient than the sequential use of sodium persulfate followed by hydrogen peroxide in advanced oxidation processes aiming at treatingstabilizedlandfill leachate.
    Matched MeSH terms: Sodium Compounds
  6. Hilles AH, Abu Amr SS, Hussein RA, Arafa AI, El-Sebaie OD
    Water Sci Technol, 2016;73(1):102-12.
    PMID: 26744940 DOI: 10.2166/wst.2015.468
    The objective of this study was to investigate the performance of employing H2O2 reagent in persulfate activation to treat stabilized landfill leachate. A central composite design (CCD) with response surface methodology (RSM) was applied to evaluate the relationships between operating variables, such as persulfate and H2O2 dosages, pH, and reaction time, to identify the optimum operating conditions. Quadratic models for the following two responses proved to be significant with very low probabilities (<0.0001): chemical oxygen demand (COD) and NH3-N removal. The obtained optimum conditions included a reaction time of 116 min, 4.97 g S2O8(2-), 7.29 g H2O2 dosage and pH 11. The experimental results were corresponding well with predicted models (COD and NH3-N removal rates of 81% and 83%, respectively). The results obtained in the stabilized leachate treatment were compared with those from other treatment processes, such as persulfate only and H2O2 only, to evaluate its effectiveness. The combined method (i.e., /S2O8(2-)/H2O2) achieved higher removal efficiencies for COD and NH3-N compared with other studied applications.
    Matched MeSH terms: Sodium Compounds/chemistry*
  7. Fagge II, Khalid K, Noh MAM, Yusof NSM, Zain SM, Khan MN
    J Oleo Sci, 2018 Jan 01;67(1):55-66.
    PMID: 29238023 DOI: 10.5650/jos.ess17033
    Behaviors of cationic and nonionic mixed micelles in the form of hexadecyltrimethylammonium bromide (HDABr) and hexadecyltrimethylammonium bromide-Polyethylene glycol hexadecyl ether (C16E20), in the presence of inert salts (NaBr and 3,5-dichlorosodium benzoate), by the use of reaction probe between Pp and ionized PhSH (Pp = piperidine and PhSH = phenyl salicylate), has been reported in this work. The values of RXBr (RXBr denotes ion exchange constants obtained in the presence of micelles of different structural features) or KXBr (KXBr denotes ion exchange constants obtained in the presence of micelles of the same structural features) for 3,5-Cl2C6H3CO2- were almost the same at three different [HDABr]T (0.006, 0.010 and 0.015 M). The average value of RXBr or KXBr determined, in the presence of pure HDABr micelles, using semi empirical kinetic (SEK) method appeared to be almost 2½-fold larger (RXBr or KXBr = 198) than that in the presence of mixed HDABr-C16E20 micelles (RXBr or KXBr = 78). Rheological measurements indicated the existence of wormlike/twisted micelles and vesicle at 0.015 M pure HDABr, various [3,5-Cl2C6H3CO2Na], and 25 and 35℃ whereas there were evidence of only spherical micelles in the presence of mixed HDABr-C16E20 ([HDABr]T = 0.015 M and [C16E20]T = 0.006 M) at both temperatures.
    Matched MeSH terms: Sodium Compounds/chemistry*
  8. Lin CK, Bashir MJ, Abu Amr SS, Sim LC
    Water Sci Technol, 2016 Dec;74(11):2675-2682.
    PMID: 27973372
    The aim of the current study is to evaluate the effectiveness of combined persulphate with hydrogen peroxide (S2O8(2-)/H2O2) oxidation as a post-treatment of biologically treated palm oil mill effluent (POME) for the first time in the literature. The removal efficiencies of chemical oxygen demand (COD), ammoniacal nitrogen (NH3-N), and suspended solids (SS) were 36.8%, 47.6%, and 90.6%, respectively, by S2O8(2-) oxidation alone under certain operation conditions (i.e., S2O8(2-) = 0.82 g, pH 11, and contact time 20 min). Nevertheless, the combined process (S2O8(2-)/H2O2) achieved 75.8% and 87.1% removals of NH3-N and SS, respectively, under 2.45/1.63 g/g H2O2/S2O8(2-), pH 11, and 20 min oxidation. Moreover, 56.9% of COD was removed at pH 8.4.
    Matched MeSH terms: Sodium Compounds/chemistry*
  9. Concessao P, Bairy LK, Raghavendra AP
    Vet World, 2020 Aug;13(8):1555-1566.
    PMID: 33061227 DOI: 10.14202/vetworld.2020.1555-1566
    Background and Aim: Intoxication of arsenic in rats is known to result in neurological effects as well as liver and kidney dysfunction. Mucuna pruriens has been identified for its medicinal properties. The aim of the study was to investigate the protective effect of aqueous seed extract of M. pruriens on sodium arsenite-induced memory impairment, liver, and kidney functions in rats.

    Materials and Methods: The experiment was divided into short-term treatment (45 days) and long-term treatment (90 days), with each group divided into nine sub-groups consisting of six animals each. Sub-groups 1 and 2 served as normal, and N-acetylcysteine (NAC) controls, respectively. Sub-groups 3-9 received sodium arsenite in drinking water (50 mg/L). In addition, sub-group 4 received NAC (210 mg/kg b.wt) orally once daily, sub-groups 5-7 received aqueous seed extract of M. pruriens (350 mg/kg b.wt, 530 mg/kg b.wt, and 700 mg/kg b.wt) orally once daily and sub-groups 8 and 9 received a combination of NAC and aqueous seed extract of M. pruriens (350 mg/kg b.wt and 530 mg/kg b.wt) orally once daily. Following the treatment, the blood was drawn retro-orbitally to assess the liver (serum alanine transaminase [ALT], serum aspartate transaminase, and serum alkaline phosphatase) and kidney (serum urea and serum creatinine) functions. Learning and memory were assessed by passive avoidance test. Animals were sacrificed by an overdose of ketamine, and their Nissl stained hippocampal sections were analyzed for alterations in neural cell numbers in CA1 and CA3 regions.

    Results: In the short-term treatment, groups administered with M. pruriens 530 mg/kg b.wt alone and combination of NAC + M. pruriens 350 mg/kg b.wt exhibited a significant improvement in memory retention, less severe neurodegeneration, and decrease in serum ALT levels. In long-term treatment, groups administered with M. pruriens 700 mg/kg b.wt alone and combination of NAC+M. pruriens 350 mg/kg b.wt, respectively, showed better memory retention, decreased neural deficits, and reduced levels of kidney and liver enzymes.

    Conclusion: The seed extract of M. pruriens showed significant enhancement in memory and learning. The number of surviving neurons in the CA1 and CA3 regions also increased on treatment with M. pruriens. Serum ALT, serum urea, and serum creatinine levels showed significant improvement on long-term treatment with M. pruriens.

    Matched MeSH terms: Sodium Compounds
  10. Anis Syuhada Mohd Saidi, Chin HC, Sharifah Nabihah Syed Jaafar, Farah Nadia Mohammad Padzil, Sarani Zakaria
    Sains Malaysiana, 2016;45:263-270.
    Cellulose was extracted from kenaf core pulp (KCP) by a series of bleaching processes (D) and alkali treatment (E) in the sequence of (DEED) and pretreated with acid hydrolysis in room temperature for 6 hours. The pretreated and non-treated cellulose were dissolved in lithium hydroxide/urea (LiOH/urea) and subsequently used to produce cellulose membrane cross linked with various percentages of glyoxal from 2.5 to 20%. The effects of acid hydrolysis pretreatment on solubility, crystallinity and morphology were investigated. The acid hydrolysis pretreatment leads to higher solubility of the cellulose solution. The formation of cellulose II and crystallinity index of the cellulose membrane were examined by X-ray diffraction (XRD). Cellulose membrane without acid hydrolysis pretreatment cross linked with higher percentage of glyoxal has higher tensile strength compared with the treated cellulose.
    Matched MeSH terms: Sodium Compounds
  11. Ahmad R, Abdullah MMAB, Ibrahim WMW, Hussin K, Ahmad Zaidi FH, Chaiprapa J, et al.
    Materials (Basel), 2021 Feb 25;14(5).
    PMID: 33669116 DOI: 10.3390/ma14051077
    The primary motivation of developing ceramic materials using geopolymer method is to minimize the reliance on high sintering temperatures. The ultra-high molecular weight polyethylene (UHMWPE) was added as binder and reinforces the nepheline ceramics based geopolymer. The samples were sintered at 900 °C, 1000 °C, 1100 °C, and 1200 °C to elucidate the influence of sintering on the physical and microstructural properties. The results indicated that a maximum flexural strength of 92 MPa is attainable once the samples are used to be sintered at 1200 °C. It was also determined that the density, porosity, volumetric shrinkage, and water absorption of the samples also affected by the sintering due to the change of microstructure and crystallinity. The IR spectra reveal that the band at around 1400 cm-1 becomes weak, indicating that sodium carbonate decomposed and began to react with the silica and alumina released from gels to form nepheline phases. The sintering process influence in the development of the final microstructure thus improving the properties of the ceramic materials.
    Matched MeSH terms: Sodium Compounds
  12. Sattar A, Aziz-Ur-Rehman -, Abbasi MA, Siddiqui SZ, Rasool S, Ali Shah SA
    Pak J Pharm Sci, 2020 Jul;33(4):1697-1705.
    PMID: 33583804
    A series of propanamide compounds 6a-l was derived by N-substitution reactions, encompassing tosyl, piperidine and 1,3,4-oxadiazole moieties. The intended array of compounds 6a-l was afforded by a series of five steps reaction scheme. 1-Tosylpiperidin-4-carboxylate (1) was synthesized by the reaction of tosyl chloride (a) with ethyl isonipecotate (b) under mild basic conditions. Compound 1 was subjected to nucleophillic substitution by hydrazine to synthesize 1-tosylpiperidin-4-carbohydrazide (2). The compound, 5-(1-tosylpiperidin-4-yl)-1,3,4-oxadiazole-2-thiol (3) was synthesized by intermolecular cyclization of compound 2 by CS2 under strong basic conditions. The target compounds, 6a-l, were finally synthesized from 3 by reacting with different electrophiles, 5a-l, in an aprotic polar solvent with sodium hydride as an activator. The different propanamoyl electrophiles, 5a-l, were synthesized by the reaction of different aromatic and aliphatic amines, 4a-l, with 3-bromopropionyl chloride under mild basic conditions. The structural elucidation was carried out using modern spectroscopic techniques including IR, 1H-NMR and EI-MS. The antibacterial potential of synthesized compounds was assessed against five bacterial strains. Compounds 6a, 6c, 6d, 6e and 6f were found to be potent antibacterial agents.
    Matched MeSH terms: Sodium Compounds
  13. Mohd Zain N.S., Tajudin S.S., Mohd Noor S.N.F., Mohamad H.
    MyJurnal
    Thisstudy aim tocharacterize melt-derivedbioactive glass and to determinethe bioactive glass (BG) suitability for dental usagethrough proliferative activity assessment of stem cells from human exfoliated deciduous teeth (SHED)when exposed to bioactive glass conditioned medium. Bioglass 45S5 in mole percentages (46.13% SiO2, 26.91% CaO, 24.35% Na2O and 2.60% P2O5)was synthesizedthrough melt-derived and characterized usingX-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR)to confirm and identify its properties.SHEDwere used to evaluate the biocompatibility of 45S5 by exposing the cells to various concentration of BG-conditioned medium (1-10 mg/ml) using alamarBlue assay. The BG produced has an amorphous structureas shown by XRD analysis. TheSi-O-Si bending, asymmetric Si-O stretching and asymmetricSi-O-Si stretchingbands were observed in the BG structure supporting the presenceof silicate network. For alamarBlue assay, SHED cultured in BG-conditioned medium showed high proliferation rate when subjected to minimal powder content in the DMEM cell culture medium.Hence, it can be concluded that SHED cultured in lower powder content of the BG-conditioned media showedhigh proliferative activity suggesting the potential of the BG for dental usage.
    Matched MeSH terms: Sodium Compounds
  14. Ahmad S, Zaib S, Jalil S, Shafiq M, Ahmad M, Sultan S, et al.
    Bioorg Chem, 2018 10;80:498-510.
    PMID: 29996111 DOI: 10.1016/j.bioorg.2018.04.012
    In this research work, we report the synthesis and biological evaluation of two new series of 1-benzyl-4-(benzylidenehydrazono)-3,4-dihydro-1H-benzo[c] [1,2]thiazine 2,2-dioxides and 1-benzyl-4-((1-phenylethylidene)hydrazono)-3,4-dihydro-1H-benzo[c][1,2]thiazine 2,2-dioxides. The synthetic plan involves the mesylation of methyl anthranilate with subsequent N-benzylation of the product. The methyl 2-(N-benzylmethylsulfonamido)benzoate was subjected to cyclization reaction in the presence of sodium hydride to obtain 1-benzyl-1H-benzo[c][1,2]thiazin-4(3H)-one 2,2-dioxide which was treated with hydrazine hydrate to get corresponding hydrazone precursor. Finally, the titled compounds were obtained by reaction of hydrazone with various substituted aldehydes and ketones. The synthesized derivatives were subjected to carry out their inhibition activities against monoamine oxidases along with modelling investigations to evaluate their binding interactions and dynamic stability during the docking studies. The inhibition profile of potent compounds was found as competitive for both the isozymes. The compounds were more selective inhibitors of MAO-A as compared to MAO-B. Moreover, drug likeness profile of the derivatives was evaluated to have an additional insight into the physicochemical properties. The molecular dynamic simulations predicted the behaviour of amino acids with the active site residues.
    Matched MeSH terms: Sodium Compounds
  15. Shaari N, Kamarudin SK, Basri S
    Heliyon, 2018 Sep;4(9):e00808.
    PMID: 30246163 DOI: 10.1016/j.heliyon.2018.e00808
    The influence of methanol as a solvent on the properties of sodium alginate/sulfonated graphene oxide (SA/SGO) membranes was explored in water-methanol mixed conditions with various methanol concentrations and temperatures through molecular dynamics simulations. The methanol uptake of the membrane showed an isolation phase determined from the simulation results. The distance between the sulfonic acid groups increased in higher methanol concentrations, as observed from S-S RDFs. Furthermore, the distance between the SA-chain RDFs and the solvent molecules was analysed to determine a) the affinity of water towards the sulfonic acid groups and b) the affinity of the aromatic backbone of the SA towards methanol molecules. A decrease in water molecule diffusion led to an increase in methanol diffusion and uptake. SA/SGO membranes exhibited a smaller diffusion coefficient than that for the Nafion membranes, as calculated from simulation results and compared to the experimental work. Additionally, the diffusion ability increased at higher temperatures for all permeants. The interaction information obtained is useful for DMFC applications.
    Matched MeSH terms: Sodium Compounds
  16. Ahmad S, Jalil S, Zaib S, Aslam S, Ahmad M, Rasul A, et al.
    Eur J Pharm Sci, 2019 Apr 01;131:9-22.
    PMID: 30735822 DOI: 10.1016/j.ejps.2019.02.007
    We report the synthesis and biological evaluation of two new series of 2-amino-6-benzyl-4-phenyl-4,6-dihydrobenzo[c]pyrano[2,3-e][1,2]thiazine-3‑carbonitrile 5,5-dioxides and 2-amino-6-methyl-4-phenyl-4,6-dihydrobenzo[c]pyrano[2,3-e][1,2]thiazine-3‑carbonitrile 5,5-dioxides. The synthetic methodology involves a multistep reaction starting with methyl anthranilate which was coupled with methane sulfonyl chloride. The product of the reaction was subjected to N-benzylation and N-methylation reactions followed by ring closure with sodium hydride resulting in the formation of respective 2,1-benzothiazine 2,2-dioxides. These 2,1-benzothiazine precursors were subjected to multicomponent reaction with malononitrile and substituted benzaldehydes for the synthesis of two new series of pyranobenzothiazines (6a-r and 7a-r). The synthesized compounds were screened as selective inhibitors of monoamine oxidase A and monoamine oxidase B. The in vitro results suggested that compound 6d and 7q are the selective inhibitors of monoamine oxidase A, however, the selective and potent inhibitors of monoamine oxidase B included compounds 6h and 7r. Moreover, some dual inhibitors were noticed like 7l having more inhibitory activity towards both the isozymes. Moreover, the binding modes of the selective and potent inhibitors of monoamine oxidase A and B were investigated by molecular docking analysis. The results suggested that the synthetic derivatives may be potential towards the monoamine oxidase isozymes.
    Matched MeSH terms: Sodium Compounds
  17. Yatongchai C, Placek LM, Curran DJ, Towler MR, Wren AW
    J Biomater Appl, 2015 Nov;30(5):495-511.
    PMID: 26116020 DOI: 10.1177/0885328215592866
    Hydroxyapatite (Ca10(PO4)6(OH)2) is widely investigated as an implantable material for hard tissue restoration due to its osteoconductive properties. However, hydroxyapatite in bulk form is limited as its mechanical properties are insufficient for load-bearing orthopedic applications. Attempts have been made to improve the mechanical properties of hydroxyapatite, by incorporating ceramic fillers, but the resultant composite materials require high sintering temperatures to facilitate densification, leading to the decomposition of hydroxyapatite into tricalcium phosphate, tetra-calcium phosphate and CaO phases. One method of improving the properties of hydroxyapatite is to incorporate bioactive glass particles as a second phase. These typically have lower softening points which could possibly facilitate sintering at lower temperatures. In this work, a bioactive glass (SiO2-CaO-ZnO-Na2O-TiO2) is incorporated (10, 20 and 30 wt%) into hydroxyapatite as a reinforcing phase. X-ray diffraction confirmed that no additional phases (other than hydroxyapatite) were formed at a sintering temperature of 560 ℃ with up to 30 wt% glass addition. The addition of the glass phase increased the % crystallinity and the relative density of the composites. The biaxial flexural strength increased to 36 MPa with glass addition, and there was no significant change in hardness as a function of maturation. The pH of the incubation media increased to pH 10 or 11 through glass addition, and ion release profiles determined that Si, Na and P were released from the composites. Calcium phosphate precipitation was encouraged in simulated body fluid with the incorporation of the bioactive glass phase, and cell culture testing in MC-3T3 osteoblasts determined that the composite materials did not significantly reduce cell viability.
    Matched MeSH terms: Sodium Compounds/chemistry*
  18. Mohammed BS, Haruna S, Wahab MMA, Liew MS, Haruna A
    Heliyon, 2019 Sep;5(9):e02255.
    PMID: 31687531 DOI: 10.1016/j.heliyon.2019.e02255
    In this present experimental study, geopolymer cement is developed using high calcium fly ash and used in the production of one-part alkali-activated binders. At 8-16 percent of the total precursor materials, the HCFA was activated with anhydrous sodium metasilicate powder and cured in ambient condition. Five mixtures of one-part geopolymer paste were intended at a steady w/b proportion. Density, flowability, setting time, compressive strength, splitting tensile strength and molar ratio impact were envisaged. It was observed that the setting time of the designed one-part geopolymer paste decreases with higher activator content. The experimental findings showed that the resistance of one-part geopolymer cement paste increases with comparatively greater activator content. However, raising the granular activator beyond 12 percent by fly ash weight decreases the strength and workability of the established one-part geopolymer cement. The optimum mix by weight of the fly ash was discovered to be 12 percent (i.e. 6 percent Na2O). At 28 days of curing, one-part alkali-activated paste recorded the greatest compressive strength of almost 50 MPa. The density of the one-part geopolymer paste is nearly the same regardless of the mixes. Microstructural assessment by FESEM, FTIR and XRD has shown that the established geopolymer paste includes quartz, pyrrhotite, aluminosilicate sodium and hydrate gels of calcium aluminosilicate. Based on the experimental information acquired, it can be deduced that the strength growth of one-part geopolymer cement is similar to that of Portland cement.
    Matched MeSH terms: Sodium Compounds
Filters
Contact Us

Please provide feedback to Administrator ([email protected])

External Links