Displaying publications 1 - 20 of 27 in total

Abstract:
Sort:
  1. Simultaneous removal of Congo red and cadmium(II) from aqueous solutions using graphene oxide-silica composite as a multifunctional adsorbent
    Mahmoudi E, Azizkhani S, Mohammad AW, Ng LY, Benamor A, Ang WL, et al.
    J Environ Sci (China), 2020 Dec;98:151-160.
    PMID: 33097147 DOI: 10.1016/j.jes.2020.05.013
    Graphene oxide is a very high capacity adsorbent due to its functional groups and π-π interactions with other compounds. Adsorption capacity of graphene oxide, however, can be further enhanced by having synergistic effects through the use of mixed-matrix composite. In this study, silica-decorated graphene oxide (SGO) was used as a high-efficiency adsorbent to remove Congo red (CR) and Cadmium (II) from aqueous solutions. The effects of solution initial concentration (20 to 120 mg/l), solution pH (pH 2 to 7), adsorption duration (0 to 140 min) and temperature (298 to 323 K) were measured in order to optimize the adsorption conditions using the SGO adsorbent. Morphological analysis indicated that the silica nanoparticles could be dispersed uniformly on the graphene oxide surfaces. The maximum capacities of adsorbent for effective removal of Cd (II) and CR were 43.45 and 333.33 mg/g based on Freundlich and Langmuir isotherms, respectively. Langmuir and Freundlich isotherms displayed the highest values of Qmax for CR and Cd (II) adsorption in this study, which indicated monolayer adsorption of CR and multilayer adsorption of Cd (II) onto the SGO, respectively. Thermodynamic study showed that the enthalpy (ΔH) and Gibbs free energy(ΔG) values of the adsorption process for both pollutants were negative, suggesting that the process was spontaneous and exothermic in nature. This study showed active sites of SGO (π-π, hydroxyl, carboxyl, ketone, silane-based functional groups) contributed to an enormous enhancement in simultaneous removal of CR and Cd (II) from an aqueous solution, Therefore, SGO can be considered as a promising adsorbent for future water pollution control and removal of hazardous materials from aqueous solutions.
    Matched MeSH terms: Congo Red*
  2. Chitosan functionalized bismuth oxychloride/zinc oxide nanocomposite for enhanced photocatalytic degradation of Congo red
    Ranjithkumar R, Van Nguyen C, Wong LS, Thiruvengadam Nandagopal JG, Djearamane S, Palanisamy G, et al.
    Int J Biol Macromol, 2023 Jan 15;225:103-111.
    PMID: 36481334 DOI: 10.1016/j.ijbiomac.2022.11.302
    The industrial discharge of dye pollutant contaminated wastewater is the major cause of water and soil pollution. Photocatalysis is a promising and green remediation technology, which has received widespread attention in the remediation of hazardous dyes from aqueous environment and convert them into harmless compounds. Herein, we report the synthesis of chitosan (CS) functionalized bismuth oxychloride/zinc oxide (BiOCl/ZnO) nanocomposite by a modified hydrothermal route. The physiochemical characterization revealed that the synthesized nanocomposite have crystalline, agglomerated spherical along with rod shaped morphology and size range from 35 to 160 nm. FTIR peaks at 825, 727, 662 and 622 cm-1 specified the presence of BiO and ZnO bonds, whereas peak at 1635 cm-1 revealed the existence of amine groups which confirms the presence of CS in the synthesized CS-BiOCl/ZnO nanocomposite. Catalytic property of synthesized nanocomposite was evaluated by the degradation of Congo red (CR) under UV-light irradiation. CR dye degradation percentage was found to be 93 % within a short period of 40 min by utilizing UV-light. Furthermore, reusability of CS-BiOCl/ZnO photocatalyst was also investigated, and it remained significant photocatalytic activity after three consecutive cycles. Hence, the results obtained in this study revealed that CS-BiOCl/ZnO nanocomposite can be used as a potential photocatalyst to remediate organic pollutants in various industries.
    Matched MeSH terms: Congo Red/chemistry
  3. Vanadia as an electron-hole recombination inhibitor on fibrous silica-titania for selective hole oxidation of ciprofloxacin and Congo red photodegradation
    Hassan NS, Jalil AA, Fei ICM, Razak MTA, Khusnun NF, Bahari MB, et al.
    Chemosphere, 2023 Oct;338:139502.
    PMID: 37453521 DOI: 10.1016/j.chemosphere.2023.139502
    Vanadia (V2O5)-incorporated fibrous silica-titania (V/FST) catalysts, which were successfully synthesized using a hydrothermal method followed by the impregnation of V2O5. The catalysts were then characterized using numerous techniques, including X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy, nitrogen adsorption-desorption analyses, ultraviolet-visible diffuse reflectance spectroscopy, Fourier-transform infrared, X-ray photoelectron spectroscopy, and photoluminescence (PL) analyses. The study found that varying the amount of V2O5 (1-10 wt%) had a significant impact on the physicochemical properties of the FST, which in turn improved the photodegradation efficiency of two organic compounds, ciprofloxacin (CIP) and congo red (CR). 5V/FST demonstrated the best performance in degrading 10 mg L-1 of CIP (83%) and CR (100%) at pH 3 using 0.375 g L-1 catalyst under visible light irradiation within 180 min. The highest photoactivity of 5V/FST is mainly due to higher crystallinity and the highest number of V2O5-FST interactions. Furthermore, as demonstrated by PL analysis, the 5V/FST catalyst has the most significant impact on interfacial charge transfer and reduces electron-hole recombination. The photodegradation of both contaminants follows the Langmuir-Hinshelwood pseudo-first-order model, according to the kinetic study. The scavenger investigation demonstrated that hydroxyl radicals and holes dominated species in the system, indicating that the catalyst effectively generated reactive species for pollutant degradation. A possible mechanism was also identified for FST and 5V/FST. Interestingly, V2O5 acts as an electron-hole recombination inhibitor on FST for selective hole oxidation of ciprofloxacin and congo red photodegradation. Finally, the degradation efficiency of the catalyst remained relatively stable even after five cyclic experiments, indicating its potential for long-term use in environmental remediation.
    Matched MeSH terms: Congo Red*
  4. Congo red dye removal from aqueous environment by cationic surfactant modified-biomass derived carbon: Equilibrium, kinetic, and thermodynamic modeling, and forecasting via artificial neural network approach
    Karaman C, Karaman O, Show PL, Karimi-Maleh H, Zare N
    Chemosphere, 2022 Mar;290:133346.
    PMID: 34929270 DOI: 10.1016/j.chemosphere.2021.133346
    Herein, it was aimed to optimize, model, and forecast the biosorption of Congo Red onto biomass-derived biosorbent. Therefore, the waste-orange-peels were processed to fabricate biomass-derived carbon, which was activated by ZnCl2 and modified with cetyltrimethylammonium bromide. The physicochemical properties of the biosorbents were explored by scanning electron microscopy and N2 adsorption/desorption isotherms. The effects of pH, initial dye concentration, temperature, and contact duration on the biosorption capacity were investigated and optimized by batch experimental process, followed by the kinetics, equilibrium, and thermodynamics of biosorption were modeled. Furthermore, various artificial neural network (ANN) architectures were applied to experimental data to optimize the ANN model. The kinetic modeling of the biosorption offered that biosorption was in accordance both with the pseudo-second-order and saturation-type kinetic model, and the monolayer biosorption capacity was calculated as 666.67 mg g-1 at 25 °C according to Langmuir isotherm model. According to equilibrium modeling, the Freundlich isotherm model was better fitted to the experimental data than the Langmuir isotherm model. Moreover, the thermodynamic modeling revealed biosorption took place spontaneously as an exothermic process. The findings revealed that the best ANN architecture trained with trainlm as the backpropagation algorithm, with tansig-purelin transfer functions, and 14 neurons in the single hidden layer with the highest coefficient of determination (R2 = 0.9996) and the lowest mean-squared-error (MSE = 0.0002). The well-agreement between the experimental and ANN-forecasted data demonstrated that the optimized ANN model can predict the behavior of the anionic dye biosorption onto biomass-derived modified carbon materials under various operation conditions.
    Matched MeSH terms: Congo Red*
  5. Lignocellulosic biomass supported metal nanoparticles for the catalytic reduction of organic pollutants
    Akhtar K, Ali F, Sohni S, Kamal T, Asiri AM, Bakhsh EM, et al.
    Environ Sci Pollut Res Int, 2020 Jan;27(1):823-836.
    PMID: 31811610 DOI: 10.1007/s11356-019-06908-y
    Lignocellulosic biomass waste is a cheap, eco-friendly, and sustainable raw material for a wide array of applications. In the present study, an easy, fast, and economically feasible route has been proposed for the preparation of different zero-valent metal nanoparticles (ZV-MNPs) based on Cu, Co, Ag, and Ni NPs using empty fruit bunch (EFB) biomass residue as support material. The catalytic efficiency of ZV-MNPs/EFB catalyst was investigated against five model pollutants, such as methyl orange (MO), congo red (CR), methylene blue (MB), acridine orange (AO), and 4-nitrophenol (4-NP) using NaBH4 as a source of hydrogen and electron. Comparative study revealed that among as-prepared ZV-MNPs/EFB catalysts, Cu-NPs immobilized onto EFB (Cu/EFB) exhibited maximum catalytic efficiency towards pollutant abasement. Degradation reactions were highly efficient, and were completed within a short time (4 min) in case of MO, CR, and MB, whilst AO and 4-NP were reduced in less than 15 min. Kinetic investigation revealed that the degradation rate of model pollutants accorded with pseudo-first order model. Furthermore, supported catalysts were easily recovered after the completion of experiment by simply pulling the catalyst from reaction system. Recyclability tests performed on Cu/EFB revealed that more than 97% of the reduction was achieved in case of MO dye for four successive cycles of reuse. The as-prepared heterostructure showed multifunctional properties, such as enhanced uptake of contaminants, high catalytic efficiency, and easy recovery, hence, offers great prospects in wastewater purification.
    Matched MeSH terms: Congo Red/chemistry
  6. Production of eco-friendly adsorbent of kaolin clay and cellulose extracted from peanut shells for removal of methylene blue and congo red removal dyes
    Reghioua A, Atia D, Hamidi A, Jawad AH, Abdulhameed AS, Mbuvi HM
    Int J Biol Macromol, 2024 Apr;263(Pt 1):130304.
    PMID: 38382796 DOI: 10.1016/j.ijbiomac.2024.130304
    This present work targets the production of an eco-friendly adsorbent (hereinafter KA/CEL) from kaolin clay functionalized with cellulose extract obtained from peanut shells. The adsorbents were used for decolorization of two different types of organic dyes (cationic: methylene blue, MB; anionic: Congo red, CR) from an aqueous environment. Several analytical methods, including Brunauer-Emmett-Teller (surface properties), Fourier Transforms infrared (functionality), scanning electron microscope, Energy dispersive X-Ray (morphology), and pHpzc test (surface charge), were used to attain the physicochemical characteristics of KA/CEL. The Box-Behnken Design (BBD) was applied to determine the crucial factors affecting adsorption performance. These included cellulose loading at 25 %, an adsorbent dose of 0.06 g, solution pH set at 10 for MB and 7 for CR, a temperature of 45 °C, and contact times of 12.5 min for MB and 20 min for CR dye. The adsorption data exhibited better agreement with the pseudo-second-order kinetic and Freundlich models. The Langmuir model estimated the monolayer capacity to be 291.5 mg/g for MB and 130.7 mg/g for CR at a temperature of 45 °C. This study's pivotal finding underscores the promising potential of KA/CEL as an effective adsorbent for treating wastewater contaminated with organic dyes.
    Matched MeSH terms: Congo Red*
  7. Engineered biochar via microwave CO2 and steam pyrolysis to treat carcinogenic Congo red dye
    Yek PNY, Peng W, Wong CC, Liew RK, Ho YL, Wan Mahari WA, et al.
    J Hazard Mater, 2020 08 05;395:122636.
    PMID: 32298946 DOI: 10.1016/j.jhazmat.2020.122636
    We developed an innovative single-step pyrolysis approach that combines microwave heating and activation by CO2 or steam to transform orange peel waste (OPW) into microwave activated biochar (MAB). This involves carbonization and activation simultaneously under an inert environment. Using CO2 demonstrates dual functions in this approach, acting as purging gas to provide an inert environment for pyrolysis while activating highly porous MAB. This approach demonstrates rapid heating rate (15-120 °C/min), higher temperature (> 800 °C) and shorter process time (15 min) compared to conventional method using furnace (> 1 h). The MAB shows higher mass yield (31-44 wt %), high content of fixed carbon (58.6-61.2 wt %), Brunauer Emmett Teller (BET) surface area (158.5-305.1 m2/g), low ratio of H/C (0.3) and O/C (0.2). Activation with CO2 produces more micropores than using steam that generates more mesopores. Steam-activated MAB records a higher adsorption efficiency (136 mg/g) compared to CO2 activation (91 mg/g), achieving 89-93 % removal of Congo Red dye. The microwave pyrolysis coupled with steam or CO2 activation thereby represents a promising approach to transform fruit-peel waste to microwave-activated biochar that remove hazardous dye.
    Matched MeSH terms: Congo Red
  8. Integrated adsorption-solar photocatalytic membrane reactor for degradation of hazardous Congo red using Fe-doped ZnO and Fe-doped ZnO/rGO nanocomposites
    Ong CB, Mohammad AW, Ng LY
    Environ Sci Pollut Res Int, 2019 Nov;26(33):33856-33869.
    PMID: 29943245 DOI: 10.1007/s11356-018-2557-2
    In this work, synergistic effect of solar photocatalysis integrated with adsorption process towards the degradation of Congo red (CR) was investigated via two different approaches using a photocatalytic membrane reactor. In the first approach, sequential treatments were conducted through the adsorption by graphene oxide (GO) and then followed by photocatalytic oxidation using Fe-doped ZnO nanocomposites (NCs). In the second approach, however, CR solution was treated by photocatalytic oxidation using Fe-doped ZnO/rGO NCs. These nanocomposites were synthesized by a sol-gel method. The NCs were characterized by X-ray diffraction (XRD), photoluminescence (PL), Fourier transmission infrared (FTIR), ultraviolet-visible (UV-vis) spectroscopy, and field emission scanning electron microscopy (FESEM). It was observed that Fe-doped ZnO could enhance the photoactivity of ZnO under solar light. When Fe-doped ZnO were decorated on GO sheets, however, this provided a surface enhancement for adsorption of organic pollutants. The photocatalytic performances using both approaches were evaluated based on the degradation of CR molecules in aqueous solution under solar irradiation. Nanofiltration (NF) performance in terms of CR residual removal from water and their fouling behavior during post-separation of photocatalysts was studied. Serious flux declined and thicker fouling layer on membrane were found in photocatalytic membrane reactor using Fe-doped ZnO/rGO NCs which could be attributed to the stronger π-π interaction between rGO and CR solution.
    Matched MeSH terms: Congo Red/analysis; Congo Red/chemistry*
  9. Bio-inspired ZnO NPs synthesized from Citrus sinensis peels extract for Congo red removal from textile wastewater via photocatalysis: Optimization, mechanisms, techno-economic analysis
    Yashni G, Al-Gheethi A, Radin Mohamed RMS, Dai-Viet NV, Al-Kahtani AA, Al-Sahari M, et al.
    Chemosphere, 2021 Oct;281:130661.
    PMID: 34029959 DOI: 10.1016/j.chemosphere.2021.130661
    Textile industry is one of the most environmental unfriendly industrial processes due to the massive generation of colored wastewater contaminated with dyes and other chemical auxiliaries. These contaminants are known to have undesirable consequences to ecosystem. The present study investigated the best operating parameters for the removal of congo red (CR, as the model for dye wastewater) by orange peels extract biosynthesized zinc oxide nanoparticles (ZnO NPs) via photocatalysis in an aqueous solution. The response surface methodology (RSM) with ZnO NPs loadings (0.05-0.20 g), pH (3.00-11.00), and initial CR concentration (5-20 ppm) were used for the optimization process. The applicability of ZnO NPs in the dye wastewater treatment was evaluated based on the techno-economic analysis (TEA). ZnO NPs exhibited hexagonal wurtzite structure with = C-H, C-O, -C-O-C, CC, O-H as the main functional groups. The maximum degradation of CR was more than 96% with 0.171 g of ZnO NPs, at pH 6.43 and 5 ppm of CR and 90% of the R2 coefficient. The specific cost of ZnO NPs production is USD 20.25 per kg. These findings indicated that the biosynthesized ZnO NPs with orange peels extract provides alternative method for treating dye wastewater.
    Matched MeSH terms: Congo Red
  10. Fulltext Cellulolytic, Nitrogen-fixing and Phosphate-solubilizing Micro-organisms as biological indicators of forest soil rehabilitation
    A. Tang, S.K. Wong, O.H. Ahmed, N.M. Majid
    ASM Science Journal, 2013;7(1):23-26.
    MyJurnal
    Widespread deforestation has resulted in soil degradation that is often linked to environmental and ecological changes. Rehabilitation of degraded forest is essential to prevent further degradation of the soil. Abundance of soil microbiota could serve as an essential biological indicator of soil health for rehabilitation success. An investigation was conducted to study the relationship between cellulolytic, nitrogen-fixing and phosphate-solubilizing microbial counts and age of rehabilitated forest. A random sampling design was used to obtain four replicates of five composite soil of 0–10 cm depth soil samples of 4, 9, 14 and 19-year-old rehabilitated forest. Three selective media: Congo red cellulose, nitrogen-free malate and calcium phosphate media were used for the enumerations of cellulolytic, nitrogen-fixing and phosphate-solubilizing microbes, respectively. Cellulolytic and phosphate-solubilizing microbes were counted based on the formation of clearing zones, while nitrogen-fixing microbes were based on the formation of blue halo on the respective media. There was positive linear relationship between age of the rehabilitated forest and microbial count. These findings revealed that the potentials of cellulolytic, nitrogen-fixing and phosphate-solubilizing microbial populations could be used as biological indicators of forest soil rehabilitation.
    Matched MeSH terms: Congo Red
  11. Fulltext Degradation of congo red dye in aqueous solution by using advanced oxidation processes
    Alya Nadhira Nasron, Ninna Sakina Azman, Nor Syaidatul Syafiqah Mohd Rashid, Nur Rahimah Said
    Journal of Academia Universiti Teknologi MARA Negeri Sembilan, 2018;6(2):1-11.
    MyJurnal
    Degradation of azo dyes by using advanced oxidation processes (AOPs) was conducted. In this approach, different AOPs, which are Fenton process and titanium dioxide (TiO2) catalyst, were examined and compared for the degradation of an azo dye (i.e., Congo red dye). The sample was tested under UV light and the experiment was conducted for 90 min with 15 min interval. The degradation rate of dye was determined using UV-Vis spectrophotometry. The effect of several parameters on the degradation process such as the concentration of metal ions (Fe2+, Cu2+, and Mn2+) as the catalyst in Fenton process, the concentration of hydrogen peroxide (H2O2), the mass of TiO2, and pH value of the dye solution were investigated. The initial Congo red concentration used for both techniques was 5 ppm. The results showed that the percentage degradation followed the sequence of H2O2/Fe2+/UV, H2O2/Cu2+/UV, H2O2/Mn2+/UV, and TiO2/UV. The best operating conditions for H2O2/Fe2+/UV were pH 3, 0.2 M concentration of H2O2, and 0.02 M concentration of metal ion in 15 min, which achieved 99.92% degradation of dye. The Fourier transform infrared (FTIR) spectrum showed the absence of azo bond (N=N) peak after degradation process, which indicates the successful cleavage of azo bond in the chemical structure of Congo red.
    Matched MeSH terms: Congo Red
  12. Biosynthesized Fe- and Ag-doped ZnO nanoparticles using aqueous extract of Clitoria ternatea Linn for enhancement of sonocatalytic degradation of Congo red
    Chan YY, Pang YL, Lim S, Lai CW, Abdullah AZ, Chong WC
    Environ Sci Pollut Res Int, 2020 Oct;27(28):34675-34691.
    PMID: 31628641 DOI: 10.1007/s11356-019-06583-z
    Nowadays, the current synthesis techniques used in industrial production of nanoparticles have been generally regarded as nonenvironmentally friendly. Consequently, the biosynthesis approach has been proposed as an alternative to reduce the usage of hazardous chemical compounds and harsh reaction conditions in the production of nanoparticles. In this work, pure, iron (Fe)-doped and silver (Ag)-doped zinc oxide (ZnO) nanoparticles were successfully synthesized through the green route using Clitoria ternatea Linn. The optical, chemical, and physical properties of the biosynthesized ZnO nanoparticles were then analyzed by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectroscopy (EDX), UV-Vis diffuse reflectance spectroscopy (DRS), zeta potential measurement, Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and surface analysis. The biosynthesized ZnO nanoparticles were crystallized with a hexagonal wurtzite structure and possessed smaller particle sizes than those of commercially or chemically produced samples. The existence of biomolecules to act as reducing and stabilizing agents from C. ternatea Linn aqueous extract was confirmed using FTIR analysis. The biosynthesized ZnO nanoparticles mainly comprised of negatively charged groups and responsible for moderately stable dispersion of the nanoparticles. All these properties were favorable for the sonocatalytic degradation of Congo red. Sonocatalytic activity of ZnO nanoparticles was studied through the degradation of 10 mg/L Congo red using ultrasonic irradiation at 45 kHz and 80 W. The results showed that the sonocatalytic degradation efficiency of Congo red in the presence of biosynthesized ZnO nanoparticles prepared at 50 °C for 1 h could achieve 88.76% after 1 h. The sonocatalytic degradation efficiency of Congo red in the presence of Ag-doped ZnO was accelerated to 94.42% after 10 min which might be related to the smallest band gap energy (3.02 eV) and the highest specific surface area (10.31 m2/g) as well as pore volume (0.0781 cm3/g). Lastly, the biosynthesized ZnO nanoparticles especially Ag-doped ZnO offered significant antibacterial potential against Escherichia coli which indicated its ability to inhibit the normal growth and replication of bacterial cells. These results affirmed that the biosynthesized ZnO nanoparticles could be used as an alternative to the current chemical compounds and showed a superior sonocatalytic activity toward degradation of Congo red.
    Matched MeSH terms: Congo Red
  13. Development of sustainable dye adsorption system using nutraceutical industrial fennel seed spent-studies using Congo red dye
    Taqui SN, Yahya R, Hassan A, Nayak N, Syed AA
    Int J Phytoremediation, 2017 Jul 03;19(7):686-694.
    PMID: 28121459 DOI: 10.1080/15226514.2017.1284746
    Fennel seed spent (FSS)-an inexpensive nutraceutical industrial spent has been used as an efficient biosorbent for the removal of Congo red (CR) from aqueous media. Results show that the conditions for maximum adsorption would be pH 2-4 and 30°C were ideal for maximum adsorption. Based on regression fitting of the data, it was determined that the Sips isotherm (R2 = 0.994, χ2 = 0.5) adequately described the mechanism of adsorption, suggesting that the adsorption occurs homogeneously with favorable interaction between layers with favorable interaction between layers. Thermodynamic analysis showed that the adsorption is favorable (negative values for ΔG°) and endothermic (ΔH° = 12-20 kJ mol-1) for initial dye concentrations of 25, 50, and 100 ppm. The low ΔH° value indicates that the adsorption is a physical process involving weak chemical interactions like hydrogen bonds and van der Waals interactions. The kinetics revealed that the adsorption process showed pseudo-second-order tendencies with the equal influence of intraparticle as well as film diffusion. The scanning electron microscopy images of FSS show a highly fibrous matrix with a hierarchical porous structure. The Fourier transform infrared spectroscopy analysis of the spent confirmed the presence of cellulosic and lignocellulosic matter, giving it both hydrophilic and hydrophobic properties. The investigations indicate that FSS is a cost-effective and efficient biosorbent for the remediation of toxic CR dye.
    Matched MeSH terms: Congo Red/chemistry*
  14. Degradation of methyl orange and congo red by using chitosan/polyvinyl alcohol/TiO2 electrospun nanofibrous membrane
    Habiba U, Lee JJL, Joo TC, Ang BC, Afifi AM
    Int J Biol Macromol, 2019 Jun 15;131:821-827.
    PMID: 30904531 DOI: 10.1016/j.ijbiomac.2019.03.132
    In this study, chitosan/polyvinyl alcohol/TiO2 nanofiber was fabricated via electrospinning at a pump rate of 1.5 mL/h and voltage 6 kV. Field-emission scanning electron microscopic images showed bead free finer nanofiber. Fourier transform infrared spectra proved the formation of strong bond among chitosan, polyvinyl alcohol and TiO2. X-ray powder diffraction showed that TiO2 became amorphous in the composite nanofiber. Toughness and thermal stability of the chitosan/PVA nanofibrous membrane was increased with addition TiO2. The chitosan/PVA/TiO2 nanofibrous membrane was stable at basic medium. But degraded in acidic and water medium after 93 and 162 h, respectively. The adsorption mechanism of congo red obeyed the Langmuir isotherm model. On the other hand, adsorption characteristic of methyl orange fitted well with both Langmuir and Freundlich isotherm models. The maximum adsorption capacity of the resulting membrane for congo red and methyl orange is 131 and 314 mg/g, respectively. However, a high dose of adsorbent was required for congo red.
    Matched MeSH terms: Congo Red/chemistry*
  15. Fulltext Detection of Biofilm Production and Its Impact on Antibiotic Resistance Profile of Bacterial Isolates from Chronic Wound Infections
    Harika K, Shenoy VP, Narasimhaswamy N, Chawla K
    J Glob Infect Dis, 2020 08 29;12(3):129-134.
    PMID: 33343163 DOI: 10.4103/jgid.jgid_150_19
    Background: Microorganisms are known to be involved in the formation of biofilm. These biofilms are often seen in chronic wound infections, surgical site infections, implants etc., These are capable of causing recalcitrant infections and most of them are also known to possess high antibiotic resistance.

    Objectives: This study was conducted to detect the biofilm formation in bacterial isolates from chronic wound infections.

    Materials and Methods: In the present study, ninety two isolates from chronic wound infections were identified by MALDI-TOF-MS (bioMerieux) and VITEK-2-MS (bioMerieux). These isolates were further screened for biofilm formation by three methods i. e., Tissue Culture Plate method (TCP), Tube Method (TM) and Congo Red Agar (CRA) method. Impact of biofilm production was correlated with the antibiotic resistant pattern.

    Statistical Analysis: Statistical analysis was done for all three methods considering TCP as Gold Standard and parameters like senitivity and specificity of TM i.e. 47.2 and 100% respectively.

    Results: Out of 92 isolates, biofilm formation was seen in 72 isolates (78.2%) by TCP method. 64 isolates were strong biofilm producers, 8 isolates were moderate biofilm producers and 20 isolates were nonbiofilm producing. High prevalence of biofilm formation was seen in nonhealing ulcers infected with Staphylococcus aureus followed by Klebsiella pneumoniae.

    Conclusion: Among three screening methods used for detection of biofilm production, TCP method is considered to be a standard and most reliable for screening of biofilm formation in comparison to TM and CRA.

    Matched MeSH terms: Congo Red
  16. Constructed wetland-microbial fuel cell for azo dyes degradation and energy recovery: Influence of molecular structure, kinetics, mechanisms and degradation pathways
    Oon YL, Ong SA, Ho LN, Wong YS, Dahalan FA, Oon YS, et al.
    Sci Total Environ, 2020 Jun 10;720:137370.
    PMID: 32325554 DOI: 10.1016/j.scitotenv.2020.137370
    Complete degradation of azo dye has always been a challenge due to the refractory nature of azo dye. An innovative hybrid system, constructed wetland-microbial fuel cell (CW-MFC) was developed for simultaneous azo dye remediation and energy recovery. This study investigated the effect of circuit connection and the influence of azo dye molecular structures on the degradation rate of azo dye and bioelectricity generation. The closed circuit system exhibited higher chemical oxygen demand (COD) removal and decolourisation efficiencies compared to the open circuit system. The wastewater treatment performances of different operating systems were ranked in the decreasing order of CW-MFC (R1 planted-closed circuit) > MFC (R2 plant-free-closed circuit) > CW (R1 planted-open circuit) > bioreactor (R2 plant-free-open circuit). The highest decolourisation rate was achieved by Acid Red 18 (AR18), 96%, followed by Acid Orange 7 (AO7), 67% and Congo Red (CR), 60%. The voltage outputs of the three azo dyes were ranked in the decreasing order of AR18 > AO7 > CR. The results disclosed that the decolourisation performance was significantly influenced by the azo dye structure and the moieties at the proximity of azo bond; the naphthol type azo dye with a lower number of azo bond and more electron-withdrawing groups could cause azo bond to be more electrophilic and more reductive for decolourisation. Moreover, the degradation pathway of AR18, AO7 and CR were elucidated based on the respective dye intermediate products identified through UV-Vis spectrophotometry, high-performance liquid chromatography (HPLC), and gas chromatograph-mass spectrometer (GC-MS) analyses. The CW-MFC system demonstrated high capability of decolouring azo dyes at the anaerobic anodic region and further mineralising dye intermediates at the aerobic cathodic region to less harmful or non-toxic products.
    Matched MeSH terms: Congo Red
  17. Heat treatment effects on the characteristics and sonocatalytic performance of TiO2 in the degradation of organic dyes in aqueous solution
    Abdullah AZ, Ling PY
    J Hazard Mater, 2010 Jan 15;173(1-3):159-67.
    PMID: 19740600 DOI: 10.1016/j.jhazmat.2009.08.060
    The ambient sonocatalytic degradation of congo red, methyl orange, and methylene blue by titanium dioxide (TiO(2)) catalyst at initial concentrations between 10 and 50mg/L, catalyst loadings between 1.0 and 3.0mg/L and hydrogen peroxide (H(2)O(2)) concentrations up to 600 mg/L is reported. A 20 kHz ultrasonic processor at 50 W was used to accelerate the reaction. The catalysts were exposed to heat treatments between 400 and 1000 degrees C for up to 4h to induce phase change. Sonocatalysts with small amount of rutile phase showed better sonocatalytic activity but excessive rutile phase should be avoided. TiO(2) heated to 800 degrees C for 2h showed the highest sonocatalytic activity and the degradation of dyes was influenced by their chemical structures, chemical phases and characteristics of the catalysts. Congo red exhibited the highest degradation rate, attributed to multiple labile azo bonds to cause highest reactivity with the free radicals generated. An initial concentration of 10mg/L, 1.5 g/L of catalyst loading and 450 ppm of H(2)O(2) gave the best congo red removal efficiency of above 80% in 180 min. Rate coefficients for the sonocatalytic process was successfully established and the reused catalyst showed an activity drop by merely 10%.
    Matched MeSH terms: Congo Red/chemistry
  18. Clear cell variant of calcifying epithelial odontogenic tumor without calcification: a rarity
    Mutalik VS, Nichat P, Carnelio S, Solomon M, Radhakrishnan R
    J Contemp Dent Pract, 2014 Jan 1;15(1):119-21.
    PMID: 24939279
    Calcifying epithelial odontogenic tumor (CEOT) is a rare, benign, locally aggressive odontogenic epithelial tumor that affects the jaws. Although there are numerous reports on the variants of CEOT, occurrence of clear cells with complete absence of calcification has been a rarity. Histochemical analysis of tumor cells revealed glycogen granules with PAS staining, with absence of CD 1a staining in clear cells, while the amyloid-like deposit associated with clear cells showed green birefringence with Congo red. We report an unusual variant of CEOT occurring in a 27 years old male patient.
    Matched MeSH terms: Congo Red
  19. Primary localised deep cutaneous amyloidosis of the eyelid
    Mun KS, Pailoor J, Reddy SC
    Malays J Pathol, 2005 Dec;27(2):113-5.
    PMID: 17191394
    A 62-year-old lady presented with a six-month history of swelling of the left upper eyelid, resulting in mild mechanical ptosis. Clinical assessment suggested a provisional diagnosis of dermoid cyst. The lesion was excised and histology revealed nodular deposits of amorphous eosinophilic material surrounded by lymphocytes and plasma cells. Special histochemistry and immunoperoxidase stain results showed deposition of amyloid, non-AA type. The lesion recurred 6 months later.
    Matched MeSH terms: Congo Red
  20. Morphologic differences in the pattern of liver infiltration between systemic AL and AA amyloidosis
    Looi LM, Sumithran E
    Hum Pathol, 1988 Jun;19(6):732-5.
    PMID: 2454214
    Biopsy and necropsy tissue from 31 unselected patients with systemic amyloidosis, in which there was histologic evidence of liver involvement, were reviewed with reference to the location and pattern of amyloid deposition in the liver. Amyloidosis was classified into AA and AL types on the basis of immunohistochemistry and permanganate reaction of the amyloid deposits. Nineteen were categorized as AA (secondary) and 12 as AL (primary) amyloidosis. Deposition of AA amyloid was limited to the walls of vessels in the portal tract, constituting a "vascular" pattern. In AL amyloidosis, the deposits exhibited a "sinusoidal" pattern in that they were seen along hepatic sinusoids as well as in vessel walls. This difference was statistically significant (P less than .001). The histologic pattern of liver infiltration offers a valuable clue in the classification of systemic amyloidosis and provides information that may be useful in the selection of patients for therapy.
    Matched MeSH terms: Congo Red
Related Terms
Filters
Contact Us

Please provide feedback to Administrator ([email protected])

External Links