Since the widespread of severe acute respiratory syndrome of coronavirus 2 (SARS-CoV-2) disease, the utilization of face masks has become omnipresent all over the world. Face masks are believed to contribute to an adequate protection against respiratory infections spread through micro-droplets among the infected person to non-infected others. However, due to the very high demands of face masks, especially the N95-type mask typically worn by medical workers, the public faces a shortage of face masks. Many papers have been published recently that focus on developing new and facile techniques to reuse and reinforce commercially available face masks. For instance, the N95 mask uses a polymer-based (membrane) filter inside, and the filter membrane can be replaced if needed. Another polymer sputtering technique by using a simple cotton candy machine could provide a cheap and robust solution for face mask fabrication. This review discuss the novel approaches of face mask reuse and reinforcement specifically by using membrane-based technology. Tuning the polymeric properties of face masks to enhance filterability and virus inactivity is crucial for future investigation.
Integrated fixed-film activated sludge (IFAS) process is considered as one of the leading-edge processes that provides a sustainable solution for wastewater treatment. IFAS was introduced as an advancement of the moving bed biofilm reactor by integrating the attached and the suspended growth systems. IFAS offers advantages over the conventional activated sludge process such as reduced footprint, enhanced nutrient removal, complete nitrification, longer solids retention time and better removal of anthropogenic composites. IFAS has been recognized as an attractive option as stated from the results of many pilot and full scales studies. Generally, IFAS achieves >90% removals for combined chemical oxygen demand and ammonia, improves sludge settling properties and enhances operational stability. Recently developed IFAS reactors incorporate frameworks for either methane production, energy generation through algae, or microbial fuel cells. This review details the recent development in IFAS with the focus on the pilot and full-scale applications. The microbial community analyses of IFAS biofilm and floc are underlined along with the special emphasis on organics and nitrogen removals, as well as the future research perspectives.
Improper disposal of municipal solid waste led to the release of heavy metals into the environment through leachate accumulation, causing a range of health and environmental problems. Phycoremediation, using microalgae to remove heavy metals from contaminated water, was investigated as a promising alternative to traditional remediation methods. This study explored the potential of Scenedesmus sp. as a phycoremediation agent for heavy metal removal from landfill leachate. The study was conducted in batch, continuous, and membrane bioreactor (MBR). In the batch system, Scenedesmus sp. was added to the leachate and incubated for 15 days before the biomass was separated from the suspension. In the continuous system, Scenedesmus sp. was cultured in a flow-through system, and the leachate was continuously fed into the system with flow rates measured at 120, 150, and 180 mL/h for 27 days. The MBR system was similar to the continuous system, but it incorporated a membrane filtration step to remove suspended solids from the treated water. The peristaltic pump was calibrated to operate at five different flow rates: 0.24 L/h, 0.30 L/h, 0.36 L/h, 0.42 L/h, and 0.48 L/h for the MBR system and ran for 24 h. The results showed that Scenedesmus sp. was effective in removing heavy metals such as lead (Pb), cobalt (Co), chromium (Cr), nickel (Ni), and zinc (Zn) from landfill leachate in all three systems. The highest removal efficiency was observed for Ni, with a removal of 0.083 mg/L in the MBR and 0.068 mg/L in batch mode. The lowest removal efficiency was observed for Zn, with a removal of 0.032 mg/L in the MBR, 0.027 mg/L in continuous mode, and 0.022 mg/L in batch mode. The findings depicted that the adsorption capacity varied among the studied metal ions, with the highest capacity observed for Ni (II) and the lowest for Zn (II), reflecting differences in metal speciation, surface charge interactions, and affinity for the adsorbent material. These factors influenced the adsorption process and resulted in varying adsorption capacities for different metal ions. The study also evaluated the biomass growth of Scenedesmus sp. and found that it was significantly influenced by the initial metal concentration in the leachate. The results of this study suggest that Scenedesmus sp. can be used as an effective phycoremediation agent for removing heavy metals from landfill leachate.