Microbial fuel cells (MFCs) are based on the biochemical reaction of microorganisms to decompose organic wastewater for converting chemical energy into power energy. MFCs are considered an environmentally friendly technology that is gaining popularity due to their simultaneous digestion and energy production abilities. To enhance its real application in wastewater treatment, this study proposes to use a non-woven material for replacing the usage of expensive membranes in MFCs. In addition, the study aims to consider a series of different aeration areas of cathode electrodes for finding an optional design. Results have shown that the adoption of non-woven with 0.45 μm can effectively prohibit the diffusion of oxygen into the anode chamber. Moreover, the non-woven material played an important role as an interface between the anode and cathode, enhancing the MFC performance. The usage of suitable non-woven material can replace the role of the membrane when applied in real wastewater applications. The results have shown that the case study where a combination of a 50% aeration area of the cathode electrodes with 25% exposure of the cathode plate in the air yielded relatively better aeration in terms of a higher current density of 250 mA/m2, higher power density of 220 mW/m2, and higher open voltage circuit of 0.4 V, compared to other case studies considered. These results indicate the optimal aeration configuration for MFCs applied in commercial wastewater treatment in the future.
The continuous growth of population and the steady improvement of people's living standards have accelerated the generation of massive food waste. Untreated food waste has great potential to harm the environment and human health due to bad odor release, bacterial leaching, and virus transmission. However, the application of traditional disposal techniques like composting, landfilling, animal feeding, and anaerobic digestion are difficult to ease the environmental burdens because of problems such as large land occupation, virus transmission, hazardous gas emissions, and poor efficiency. Pyrolysis is a practical and promising route to reduce the environmental burden by converting food waste into bioenergy. This paper aims to analyze the characteristics of food waste, introduce the production of biofuels from conventional and advanced pyrolysis of food waste, and provide a basis for scientific disposal and sustainable management of food waste. The review shows that co-pyrolysis and catalytic pyrolysis significantly impact the pyrolysis process and product characteristics. The addition of tire waste promotes the synthesis of hydrocarbons and inhibits the formation of oxygenated compounds efficiently. The application of calcium oxide (CaO) exhibits good performance in the increment of bio-oil yield and hydrocarbon content. Based on this literature review, pyrolysis can be considered as the optimal technique for dealing with food waste and producing valuable products.
Single-chamber sediment microbial fuel cells (SSMFCs) have received considerable attention nowadays because of their unique dual-functionality of power generation and enhancement of wastewater treatment performance. Thus, scaling up or upgrading SSMFCs for enhanced and efficient performance is a highly crucial task. Therefore, in order to achieve this goal, an innovative physical technique of using interface layers with four different pore sizes embedded in the middle of SSMFCs was utilized in this study. Experimental results showed that the performance of SSMFCs employing an interface layer was improved regardless of the pore size of the interface material, compared to those without such layers. The use of an interface layer resulted in a positive and significant effect on the performance of SSMFCs because of the effective prevention of oxygen diffusion from the cathode to the anode. Nevertheless, when a smaller pore size interface was utilized, better power performance and COD degradation were observed. A maximum power density of 0.032mW/m2 and COD degradation of 47.3% were obtained in the case of an interface pore size of 0.28μm. The findings in this study are of significance to promote the future practical application of SSMFCs in wastewater treatment plants.
Recycling waste cooking vegetable oils by reclaiming and using these oils as biodiesel feedstocks is one of the promising solutions to address global energy demands. However, producing these biodiesels poses a significant challenge because of their poor physicochemical properties due the high free fatty acid content and impurities present in the feedstock, which will reduce the biodiesel yields. Hence, this study implemented the following strategy in order to address this issue: (1) 70 vol% of waste cooking vegetable oil blended with 30 vol% of Calophyllum inophyllum oil named as WC70CI30 used to alter its properties, (2) a three-stage process (degumming, esterification, and transesterification) was conducted which reduces the free fatty acid content and presence of impurities, and (3) the transesterification process parameters (methanol/oil ratio, reaction temperature, reaction time, and catalyst concentration) were optimized using response surface methodology in order to increase the biodiesel conversion yield. The results show that the WC70CI30 biodiesel has favourable physicochemical properties, good cold flow properties, and high oxidation stability (22.4 h), which fulfil the fuel specifications stated in the ASTM D6751 and EN 14214 standards. It found that the WC70CI30 biodiesel has great potential as a diesel substitute without the need for antioxidants and pour point depressants.
Photosynthetic microbial fuel cells (PMFCs) are novel bioelectrochemical transducers that employ microalgae to generate oxygen, organic metabolites and electrons. Conventional PMFCs employ non-eco-friendly membranes, catalysts and phosphate buffer solution. Eliminating the membrane, buffer and catalyst can make the MFC a practical possibility. Therefore, single chambered (SPMFC) were constructed and operated at different recirculation flow rates (0, 40 and 240 ml/min) under bufferless conditions. Furthermore, maximum power density of 4.06 mW/m2, current density of 46.34 mA/m2 and open circuit potential of 0.43 V and low internal resistance of 611.8 Ω were obtained at 40 ml/min. Based on the results it was decided that SPMFC was better for operation at 40 ml/min. Therefore, these findings provided progressive insights for future pilot and industrial scale studies of PMFCs.
The purification of human adipose-derived stem cells (hADSCs) from human adipose tissue cells (stromal vascular fraction) was investigated using membrane filtration through poly(lactide-co-glycolic acid)/silk screen hybrid membranes. Membrane filtration methods are attractive in regenerative medicine because they reduce the time required to purify hADSCs (i.e., less than 30 min) compared with conventional culture methods, which require 5-12 days. hADSCs expressing the mesenchymal stem cell markers CD44, CD73, and CD90 were concentrated in the permeation solution from the hybrid membranes. Expression of the surface markers CD44, CD73, and CD99 on the cells in the permeation solution from the hybrid membranes, which were obtained using 18 mL of feed solution containing 50 × 10⁴ cells, was statistically significantly higher than that of the primary adipose tissue cells, indicating that the hADSCs can be purified in the permeation solution by the membrane filtration method. Cells expressing the stem cell-associated marker CD34 could be successfully isolated in the permeation solution, whereas CD34⁺ cells could not be purified by the conventional culture method. The hADSCs in the permeation solution demonstrated a superior capacity for osteogenic differentiation based on their alkali phosphatase activity, their osterix gene expression, and the results of mineralization analysis by Alizarin Red S and von Kossa staining compared with the cells from the suspension of human adipose tissue. These results suggest that the hADSCs capable of osteogenic differentiation preferentially permeate through the hybrid membranes.
Human adipose-derived stem cells (hADSCs) exhibit heterogeneous characteristics, indicating various genotypes and differentiation abilities. The isolated hADSCs can possess different purity levels and divergent properties depending on the purification methods used. We developed a hybrid-membrane migration method that purifies hADSCs from a fat tissue solution with extremely high purity and pluripotency. A primary fat-tissue solution was permeated through the porous membranes with a pore size from 8 to 25 μm, and the membranes were incubated in cell culture medium for 15-18 days. The hADSCs that migrated from the membranes contained an extremely high percentage (e.g., >98%) of cells positive for mesenchymal stem cell markers and showed almost one order of magnitude higher expression of some pluripotency genes (Oct4, Sox2, Klf4 and Nanog) compared with cells isolated using the conventional culture method.