This study examined the influence of pH and salt concentration on the protein solubility of slaughtered and non-slaughtered broiler chicken meat. Three types of salt (NaCl, Na2SO4, and (NH4)2SO4), five different pH levels (5.0, 6.0, 7.0, 8.0 and 9.0) and five salt concentrations (0.4, 0.8, 1.2, 1.6, and 2.0 M) were examined. Each type of salt showed distinctive activities for slaughtered and non-slaughtered meat protein solubility. Soluble protein concentration increased as pH increased (p<0.05) from pH5.0 to 8.0 and decreased from pH8.0 to 9.0. It was also observed that protein solubility increased as the salt concentration increased. Protein solubility significantly increased (p<0.05) in the non-slaughtered meat compared to the slaughtered meat at pH8.0 for Na2SO4 at 1.2 M.
This paper involves the planarization of borophosphosilicate glass (BPSG) film using a new recipe for annealing process to improve the borophosphosilicate glass (BPSG) film flatness after reflow. This improvement is for 0.35µm technology using steam annealing method at different temperatures. This process allows the planarization of wafers with thin layer at its surface. In this paper we present the comparison between the effect of hydrofluoric acid (HF) staining on the cross sectional topography with the samples without hydrofluoric acid (HF) staining analyzed by field emission scanning electron microscopy (FESEM). We found that staining with HF produced clearer images.
Normalisation is a process of removing systematic variation that affects measured gene expression levels
in microarray experiment. The purpose is to get a more accurate DNA microarray result by deleting
the systematic errors that may have occurred when making the DNA microarray slid. In this paper,
four normalisation methods of Global, Lowess, Quantile and Print-tip are discussed, tested and their
final results compared in the form of Matrixes and graphs. Ideal and real microarray slides have been
used for this project. It was found that the Print-tip normalisation method showed the closest results to
the real result for an ideal microarray slide and it has a straight median line final graph. The Print-tip
normalisation method uses more than one normalization factor that is divided among intervals which
are dependent on the values of the addition of red and green logarithm.
This paper compares and discusses the wearout reliability and analysis of Gold (Au), Palladium (Pd) coated Cu and Pd-doped Cu wires used in fineline Ball Grid Array (BGA) package. Intermetallic compound (IMC) thickness measurement has been carried out to estimate the coefficient of diffusion (Do) under various aging conditions of different bonding wires. Wire pull and ball bond shear strengths have been analyzed and we found smaller variation in Pd-doped Cu wire compared to Au and Pd-doped Cu wire. Au bonds were identified to have faster IMC formation, compared to slower IMC growth of Cu. The obtained weibull slope, β of three bonding wires are greater than 1.0 and belong to wearout reliability data point. Pd-doped Cu wire exhibits larger time-to-failure and cycles-to-failure in both wearout reliability tests in Highly Accelerated Temperature and Humidity (HAST) and Temperature Cycling (TC) tests. This proves Pd-doped Cu wire has a greater potential and higher reliability margin compared to Au and Pd-coated Cu wires.
In this article, the effect of heating duration on the synthesis of silicon carbide nanotubes (SiCNTs) was reported. SiCNTs were synthesized from blend of silicon dioxide (SiO2) and multi-walled carbon nanotubes (MWCNTs) in the ratio of 1:3 by using the microwave heating at 1400°C and maintained at duration of 20, 40 and 60 min, respectively. SiCNTs synthesized at heating duration of 40 and 60 min showed the presence of single phase β-SiC in X-ray diffraction patterns. Meanwhile, field emission scanning electron microscope images showed that SiCNTs were formed and no residual of SiO2 and MWCNTs was observed for SiCNTs formed at heating duration of 40 and 60 min. Transmission electron microscopy images showed the SiCNTs have inter-planar spacing of 0.263 nm and tubular structure of nanotube were retained. The peak corresponded to β-SiC was observed at wavelength of 465 nm from the photoluminescence spectroscopy and associated with energy band gap of 2.67 eV. Absorption bands of Si-C bond were detected at 806.23 cm-1 from the fourier transform infrared spectra. High purity SiCNTs was obtained at 40 and 60 min as indicated by low weight loss by thermo-gravimetric analysis. 40 min is the most suitable heating duration for the synthesis of single phase β-SiCNTs.