A method that delivers a high yield and excellent quality of essential oil, which retains most of its value-added compounds, and undergoes least change after the extraction process, is greatly sought after. Although chemical free methods are acceptable, they call for an extensive processing time, while the yield and quality from these methods are often disappointing. This work utilizes subcritical water technology to address these issues. In this undertaking, essential oil was extracted from Aquilaria malaccensis wood by way of subcritical conditions, and characterized through gas chromatography/mass spectroscopy (GC/MS). Optimization through response surface methodology revealed temperature to be the most critical factor for the extraction process, while the optimum conditions for temperature, sample-to-solvent ratio, and time for subcritical water extraction was revealed as 225 °C, 0.2 gr/mL, and 17 min, respectively. The subcritical water extraction technique involves two simultaneous processes, which are based on good fitting to the two-site kinetic and second order model. In comparison to the hydrodistillation method, GC/MS results indicated that the quality of A. malaccensis' wood oils, derived through the subcritical water technique, are of significantly better quality, while containing many constructive value-added compounds, such as furfural and guaiacol, which are useful for the production of pesticides and medicines. Pore size, functional groups, and morphology analysis revealed the occurrence of substantial damage to the samples, which facilitated an improved extraction of bio-products. In comparison to conventional methods, the use of the subcritical method not only involves a shorter processing time, but also delivers a higher oil yield and quality.
Malnutrition is prevalent among patients hospitalized in Intensive Care Units (ICUs) and causes various complications. Dietary supplementation to provide appropriate nutritional support may reduce the malnutrition and complications through improvement in nutritional status. This study was carried out to assess the association between dietary supplementation and malnutrition among patients in ICUs.
The recycling of millions of tons of glass bottle waste produced each year is far from optimal. In the present work, ground blast furnace slag (GBFS) was substituted in fly ash-based alkali-activated mortars (AAMs) for the purpose of preparing glass bottle waste nano-powder (BGWNP). The AAMs mixed with BGWNP were subsequently subjected to assessment in terms of their energy consumption, economic viability, and mechanical and chemical qualities. Besides affording AAMs better mechanical qualities and making them more durable, waste recycling was also observed to diminish the emissions of carbon dioxide. A more than 6% decrease in carbon dioxide emissions, an over 16% increase in compressive strength, better durability and lower water absorption were demonstrated by AAM consisting of 5% BGWNP as a GBFS substitute. By contrast, lower strength was exhibited by AAM comprising 10% BGWNP. The conclusion reached was that the AAMs produced with BGWNP attenuated the effects of global warming and thus were environmentally advantageous. This could mean that glass waste, inadequate for reuse in glass manufacturing, could be given a second life rather than being disposed of in landfills, which is significant as concrete remains the most commonplace synthetic material throughout the world.
The binary effect of pulverized fuel ash (PFA) and palm oil fuel ash (POFA) on heat of hydration of aerated concrete was studied. Three aerated concrete mixes were prepared, namely, concrete containing 100% ordinary Portland cement (control sample or Type I), binary concrete made from 50% POFA (Type II), and ternary concrete containing 30% POFA and 20% PFA (Type III). It is found that the temperature increases due to heat of hydration through all the concrete specimens especially in the control sample. However, the total temperature rises caused by the heat of hydration through both of the new binary and ternary concrete were significantly lower than the control sample. The obtained results reveal that the replacement of Portland cement with binary and ternary materials is beneficial, particularly for mass concrete where thermal cracking due to extreme heat rise is of great concern.
Every structure might be exposed to fire at some point in its lifecycle. The ability of geopolymer composites to withstand the effects of fire damage early before it is put out is of great importance. This study examined the effects of fire on geopolymer composite samples made with high-calcium fly ash and alkaline solution synthesised from waste banana peduncle and silica fume. A ratio of 0.30, 0.35, and 0.4 was used in the study for the alkaline solution to fly ash. Also used were ratios of 0.5, 0.75, and 1 for silica oxide (silica fume) to potassium hydroxide ratio. The strength loss, residual compressive strength, percentage strength loss, relative residual compressive strength, ultrasonic pulse velocity, and microstructural properties of the thirteen mortar mixes were measured after exposure to temperatures of 200, 400, 600, and 800 °C for 1 h, respectively. The results reveal that geopolymer samples exposed to elevated temperatures showed great dimensional stability with no visible surface cracks. There was a colour transition from dark grey to whitish brown for the green geopolymer mortar and brown to whitish brown for the control sample. As the temperature rose, weight loss became more pronounced, with 800 °C producing the most significant weight reduction. The optimum mixes had a residual compressive strength of 25.02 MPa after being exposed to 200 °C, 18.72 MPa after being exposed to 400 °C, 14.04 MPa after being exposed to 600 °C, and 7.41 MPa after being exposed to 800 °C. The control had a residual compressive strength of 8.45 MPa after being exposed to 200 °C, 6.67 MPa after being exposed to 400 °C, 3.16 MPa after being exposed to 600 °C, and 2.23 MPa after being exposed to 800 °C. The relative residual compressive strength decreases for green geopolymer mortar are most significant at 600 and 800 °C, with an average decrease of 0.47 and 0.30, respectively. The microstructure of the samples revealed various phase changes and new product formations as the temperature increased.