Polyimide/SiO(2) composite films were prepared from tetraethoxysilane (TEOS) and poly(amic acid) (PAA) based on aromatic diamine (4-aminophenyl sulfone) (4-APS) and aromatic dianhydride (3,3,4,4-benzophenonetetracarboxylic dianhydride) (BTDA) via a sol-gel process in N-methyl-2-pyrrolidinone (NMP). The prepared polyimide/SiO(2) composite films were characterized using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscope (SEM) and thermogravimetric analysis (TGA). The FTIR results confirmed the synthesis of polyimide (4-APS/BTDA) and the formation of SiO(2) particles in the polyimide matrix. Meanwhile, the SEM images showed that the SiO(2) particles were well dispersed in the polyimide matrix. Thermal stability and kinetic parameters of the degradation processes for the prepared polyimide/SiO(2) composite films were investigated using TGA in N(2) atmosphere. The activation energy of the solid-state process was calculated using Flynn-Wall-Ozawa's method without the knowledge of the reaction mechanism. The results indicated that thermal stability and the values of the calculated activation energies increased with the increase of the TEOS loading and the activation energy also varied with the percentage of weight loss for all compositions.
In this paper, Polyimide/Montmorillonite Nanocomposites (PI/MMT NCs), based on aromatic diamine (4-Aminophenyl sulfone) (APS) and aromatic dianhydride (3,3',4,4'-benzophenonetetracarboxylic dianhydride) (BTDA) were prepared using in situ polymerization and solution-dispersion techniques. The prepared PI/MMT NCs films were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), transmission electron microscopy (TEM) and thermogravimetric analysis (TGA). The XRD results showed that at the content of 1.0 wt % Organo Montmorillonite (OMMT) for two techniques and 3.0 wt % OMMT for the in situ polymerization technique, the OMMT was well-intercalated, exfoliated and dispersed into polyimide matrix. The OMMT agglomerated when its amount exceeded 10 wt % and 3.0 wt % for solution-dispersion and in situ polymerization techniques respectively. These results were confirmed by the TEM images of the prepared PI/MMT NCs. The TGA thermograms indicated that thermal stability of prepared PI/MMT NCs were increased with the increase of loading that, the effect is higher for the samples prepared by in situ polymerization technique.
Thermoplastic cassava starch (TPCS) is a promising alternative material to replace the non-biodegradable petroleum based polymer due to its good environmental-friendly aspect i.e. abundant, sustainable, recyclable and biodegradable in nature. However, TPCS have some limitation such as poor mechanical properties. Therefore, in the present study, cogon grass fibre (CGF) were incorporated into TPCS using compression molding. Then the fundamental properties of CFG/TPCS biopolymer composites were carried out in order to evaluate their potential as a biodegradable reinforcement. From the study it was found that, the incorporation of CFG has improved the tensile and flexural properties of the TPCS composites, while the impact strength and elongation were reduced. The thermal properties of the biocomposite were reduced as the cogon grass fibres increase from 0 to 5%. In term of morphological, SEM shows good fibre adhesion between CGF and TPCS. Soil burial test shows that incorporation of CGF into TPCS has slow down the biodegradation process of the composites. Thus, CGF/TPCS biopolymer composites can be classified as composites with great potential as environmental-friendly material that biodegradable and renewable.
The primary aim of this study is to examine the effects of a backrest: using a prototype of a lumbar support presented in author's earlier study on the discomfort rating of the body parts of motorcyclist.
This paper presents the results of an anthropometric data collected from polytechnic students in Malaysia. A total of 1032 (595 males and 437 females) students participated in the study. Their ages ranged from 18 to 24 years. A total of 34 anthropometric dimensions were measured. Descriptive statistics such as mean, standard deviation, standard error of mean, coefficient of variation, minimum, maximum and percentile for each parameter were estimated. In addition, the comparison between Malaysia anthropometric data and Thailand (South) anthropometric data were also presented. The results show that there is a total of 12 and 11 (of dimensions parameters) significant differences (p < 0.05) between the male and female adults respectively.
This research examines the impact of self-polymerized polydopamine (PDA) coating on the mechanical properties and microstructural behavior of polylactic acid (PLA)/kenaf fiber (KF) composites in fused deposition modeling (FDM). A biodegradable FDM model of natural fiber-reinforced composite (NFRC) filaments, coated with dopamine and reinforced with 5 to 20 wt.% bast kenaf fibers, was developed for 3D printing applications. Tensile, compression, and flexural test specimens were 3D printed, and the influence of kenaf fiber content on their mechanical properties was assessed. A comprehensive characterization of the blended pellets and printed composite materials was performed, encompassing chemical, physical, and microscopic analyses. The results demonstrate that the self-polymerized polydopamine coating acted as a coupling agent, enhancing the interfacial adhesion between kenaf fibers and the PLA matrix and leading to improved mechanical properties. An increase in density and porosity was observed in the FDM specimens of the PLA-PDA-KF composites, proportional to their kenaf fiber content. The enhanced bonding between kenaf fiber particles and the PLA matrix contributed to an increase of up to 13.4% for tensile and 15.3% for flexural in the Young's modulus of PLA-PDA-KF composites and an increase of up to 30% in compressive stress. The incorporation of polydopamine as a coupling agent in the FDM filament composite led to an improvement in tensile, compressive, and flexural stresses and strain at break, surpassing that of pure PLA, while the reinforcement provided by kenaf fibers was enhanced more by delayed crack growth, resulting in a higher strain at break. The self-polymerized polydopamine coatings exhibit remarkable mechanical properties, suggesting their potential as a sustainable material for diverse applications in FDM.