MyMedR

Displaying all 4 publications

Abstract:

Sort:

Fulltext Glaucoma among the Malaysian Community

Al-Naggar RA, Alshaikhli H, Al-Rashidi RR, Saleh B

ScientificWorldJournal, 2020;2020:4859496.
PMID: 32802004 DOI: 10.1155/2020/4859496

Background: According to the WHO, glaucoma is the second leading cause of blindness worldwide. About 50% of the world's glaucoma cases come from the Asian population, and in Malaysia itself, the prevalence of glaucoma is increasing. However, glaucoma is still a foreign word to our community despite the high prevalence. Therefore, there is an urgent need to determine the awareness of glaucoma among the community and its associated factors.
Results: This study showed that only 25.2% of our respondents were aware of glaucoma and it is associated with ethnicity, religion, education, and household income. Besides, among those who were aware, they fall into the group of poor knowledge of glaucoma. On the other hand, the knowledge of glaucoma was associated with occupation and the awareness of glaucoma by definition. The validated questionnaire was distributed and the data were analyzed by SPSS software using t-test, one-way ANOVA, and chi-square test.
Conclusion: Awareness and knowledge of glaucoma in this population is low. These findings suggest that there is a need for an efficient information and education strategy to be designed and conducted to increase the awareness and knowledge of glaucoma so that early detection can be made and effective management of individuals with this condition can be delivered.
Fulltext Multi Ceramic Particles Inclusion in the Aluminium Matrix and Wear Characterization through Experimental and Response Surface-Artificial Neural Networks

Sharath BN, Venkatesh CV, Afzal A, Aslfattahi N, Aabid A, Baig M, et al.

Materials (Basel), 2021 May 28;14(11).
PMID: 34071305 DOI: 10.3390/ma14112895

Lightweight composite materials have recently been recognized as appropriate materials have been adopted in many industrial applications because of their versatility. The present research recognizes the inclusion of ceramics such as Gr and B4C in manufacturing AMMCs through stir casting. Prepared composites were tested for hardness and wear behaviour. The tests' findings revealed that the reinforced matrix was harder (60%) than the un-reinforced alloy because of the increased ceramic phase. The rising content of B4C and Gr particles led to continuous improvements in wear resistance. The microstructure and worn surface were observed through SEM (Scanning electron microscope) and revealed the formation of mechanically mixed layers of both B4C and Gr, which served as the effective insulation surface and protected the test sample surface from the steel disc. With the rise in the content of B4C and Gr, the weight loss declined, and significant wear resistance was achieved at 15 wt.% B4C and 10 wt.% Gr. A response surface analysis for the weight loss was carried out to obtain the optimal objective function. Artificial neural network methodology was adopted to identify the significance of the experimental results and the importance of the wear parameters. The error between the experimental and ANN results was found to be within 1%.
Fulltext The Potential Anticancer Activity of 5-Fluorouracil Loaded in Cellulose Fibers Isolated from Rice Straw

Yusefi M, Shameli K, Jahangirian H, Teow SY, Umakoshi H, Saleh B, et al.

Int J Nanomedicine, 2020;15:5417-5432.
PMID: 32801697 DOI: 10.2147/IJN.S250047

INTRODUCTION: Green-based materials have been increasingly studied to circumvent off-target cytotoxicity and other side-effects from conventional chemotherapy.
MATERIALS AND METHODS: Here, cellulose fibers (CF) were isolated from rice straw (RS) waste by using an eco-friendly alkali treatment. The CF network served as an anticancer drug carrier for 5-fluorouracil (5-FU). The physicochemical and thermal properties of CF, pure 5-FU drug, and the 5-FU-loaded CF (CF/5-FU) samples were evaluated. The samples were assessed for in vitro cytotoxicity assays using human colorectal cancer (HCT116) and normal (CCD112) cell lines, along with human nasopharyngeal cancer (HONE-1) and normal (NP 460) cell lines after 72-hours of treatment.
RESULTS: XRD and FTIR revealed the successful alkali treatment of RS to isolate CF with high purity and crystallinity. Compared to RS, the alkali-treated CF showed an almost fourfold increase in surface area and zeta potential of up to -33.61 mV. SEM images illustrated the CF network with a rod-shaped structure and comprised of ordered aggregated cellulose. TGA results proved that the thermal stability of 5-FU increased within the drug carrier. Based on UV-spectroscopy measurements for 5-FU loading into CF, drug loading encapsulation efficiency was estimated to be 83 ±0.8%. The release media at pH 7.4 and pH 1.2 showed a maximum drug release of 79% and 46%, respectively, over 24 hours. In cytotoxicity assays, CF showed almost no damage, while pure 5-FU killed most of the both normal and cancer cells. Impressively, the drug-loaded sample of CF/5-FU at a 250 µg/mL concentration demonstrated a 58% inhibition against colorectal cancer cells, but only a 23% inhibition against normal colorectal cells. Further, a 62.50 µg/mL concentration of CF/5FU eliminated 71% and 39% of nasopharyngeal carcinoma and normal nasopharyngeal cells, respectively.
DISCUSSION: This study, therefore, showed the strong potential anticancer activity of the novel CF/5-FU formulations, warranting their further investigation.
Fulltext Optimization of Process Parameters in CNC Turning of Aluminum 7075 Alloy Using L27 Array-Based Taguchi Method

Akhtar MN, Sathish T, Mohanavel V, Afzal A, Arul K, Ravichandran M, et al.

Materials (Basel), 2021 Aug 10;14(16).
PMID: 34442992 DOI: 10.3390/ma14164470

With the advent of the industrial revolution 4.0, the goal of the manufacturing industry is to produce a large number of products in relatively less time. This study applies the Taguchi L27 orthogonal array methodological paradigm along with response surface design. This work optimizes the process parameters in the turning of Aluminum Alloy 7075 using a Computer Numerical Control (CNC) machine. The optimal parameters influenced the rate of metal removal, the roughness of the machined surface, and the force of cutting. This experimental investigation deals with the optimization of speed (800 rpm, 1200 rpm, and 1600 rpm) and feed (0.15, 0.20, and 0.25 mm/rev) in addition to cutting depth (1.0, 1.5, and 2.0 mm) on the turning of Aluminum 7075 alloy in a CNC machine. The outcome in terms of results such as the removal rate of material (maximum), roughness on the machined surface (minimum), along with cutting force (least amount) were improved by the L27 array Taguchi method. There were 27 specimens of Al7075 alloy produced as per the array, and the corresponding responses were measured with the help of various direct contact and indirect contact sensors. Results were concluded all the way through diagrams of main effects in favor of signal-to-noise ratios and diagrams of surfaces with contour diagrams for various combinations of responses.