The objective of this study was to investigate the effects of different species of oil palm shell (OPS) coarse aggregates on the properties of high strength lightweight concrete (HSLWC). Original and crushed OPS coarse aggregates of different species and age categories were investigated in this study. The research focused on two OPS species (dura and tenera), in which the coarse aggregates were taken from oil palm trees of the following age categories (3-5, 6-9, and 10-15 years old). The results showed that the workability and dry density of the oil palm shell concrete (OPSC) increase with an increase in age category of OPS species. The compressive strength of specimen CD3 increases significantly compared to specimen CT3 by 21.8%. The maximum achievable 28-day and 90-day compressive strength is 54 and 56 MPa, respectively, which is within the range for 10-15-year-old crushed dura OPS. The water absorption was determined to be within the range for good concrete for the different species of OPSC. In addition, the ultrasonic pulse velocity (UPV) results showed that the OPS HSLWC attain good condition at the age of 3 days.
A soluble poly (n-vinyl carbazole)-polypyrrole (PNVC-Ppy) copolymer was prepared through oxidative chemical polymerization wherein dodecyl benzene sulfonic acid (DBSA) was used as a dopant to facilitate polymer-organic solvent interaction and ammonium persulfate (APS) was used as an oxidant. Compared with undoped PNVC-Ppy, the DBSA-doped PNVC-Ppy copolymer showed higher solubility in some selected organic solvents. The composition and structural characteristics of the DBSA-doped PNVC-Ppy were determined by Fourier transform infrared, ultraviolet-visible, and X-ray diffraction spectroscopic methods. Field emission scanning electron microscopic method was employed to observe the morphology of the DBSA-doped PNVC-Ppy copolymer. The electrical conductivity of the DBSA-doped PNVC-Ppy copolymer was measured at room temperature. The conductivity increased with increasing concentration of APS oxidant, and the highest conductivity was recorded at 0.004 mol/dm3APS at a polymerization temperature of -5 °C. The increased conductivity can be explained by the extended half-life of pyrrole free radical at a lower temperature and a gradual increase in chain length over a prolonged time due to the slow addition of APS. Furthermore, the obtained soluble copolymer exhibits unique optical and thermal properties different from those of PNVC and Ppy.
The emergence of a pandemic affecting the respiratory system has resulted in a significant demand for face masks. Masks have always been mentioned as an effective tool against environmental threats. This includes the use of double masks by large sections of the public, as can be seen during the current global spread of COVID-19. However, there is limited knowledge available on the performance of the various commonly available double face masks used. In this study, we have compared the performance of single and double face configurations. Three types of 3-ply face mask (FM), three types of fabric face mask (CM) and nine configurations of these face masks were investigated based on morphology, filtration efficiencies, breathing resistance and carbon dioxide (CO2) content. The filtration efficiencies of the double face masks are enhanced when combined with a fabric mask, and were found to improve by 500% compared to those of a fabric mask. The lowest breathing resistance among the double masking was observed in the combination of FM1 and fabric face masks. From the results, it was found that all combinations of double face mask are suitable to use since the measurements indicate that the breathing resistance and CO2 contents are still lower than the acceptable value set by the Malaysian Standard (MS 2323:2010) and European Standard (EN 149:2001 + A1:2009). The performance of double masks is comparable with that of N95 respirators. The double masking combination can be used as an alternative method to reduce inhalation exposure to airborne contaminants.
Semi-flexible pavement surfacing is a composite pavement that utilizes the porous pavement structure of the flexible bituminous pavement, which is subsequently grouted with appropriate cementitious materials. This study aims to investigate the compressive strength, flexural strength, and workability performance of cementitious grout. The grout mixtures are designed to achieve high strength and maintain flow properties in order to allow the cement slurries to infiltrate easily through unfilled compacted skeletons. A paired-sample t-test was carried out to find out whether water/cement ratio, SP percentages, and use of silica fume influence the cementitious grout performance. The findings showed that the replacement of 5% silica fume with an adequate amount of superplasticizer and water/cement ratio was beneficial in improving the properties of the cementitious grout.
Metal tungstates have attracted much attention due to their interesting structural and photoluminescence properties. Depending on the size of the bivalent cation present, the metal tungstates will adopt structures with different phases. In this work, three different phases of metal tungstates MWO4 (M= Ba, Ni and Bi) were synthesized via the sucrose templated method.
In previous studies of Lactococcus lactis, the levels of proteins secreted using heterologous signal peptides were observed to be lower than those obtained using the signal peptide from Usp45, the major secreted lactococcal protein. In this study, G1 (the native signal peptide of CGTase) and the signal peptide M5 (mutant of the G1 signal peptide) were introduced into L. lactis to investigate the effect of signal peptides on lactococcal protein secretion to improve secretion efficiency. The effectiveness of these signal peptides were compared to the Usp45 signal peptide. The highest secretion levels were obtained using the G1 signal peptide. Sequence analysis of signal peptide amino acids revealed that a basic N-terminal signal peptide is not absolutely required for efficient protein export in L. lactis. Moreover, the introduction of a helix-breaking residue in the H-region of the M5 signal peptide caused a reduction in the signal peptide hydrophobicity and decreased protein secretion. In addition, the optimization of cultivation conditions for recombinant G1-CGTase production via response surface methodology (RSM) showed that CGTase activity increased approximately 2.92-fold from 5.01 to 16.89 U/ml compared to the unoptimized conditions.
The oxidation of ethylbenzene (EB) using tert-butyl hydroperoxide as the oxidizing agent was carried out in presence of gold nanoparticles (3 nm) supported on zinc oxide in acetonitrile solution. A higher selectivity towards acetophenone (ACP) as the major product, and a moderate selectivity towards other products such as 1-phenylethanol (PE), benzaldehyde (BZL), and benzoic acid (BzA) were observed using the prepared Au/ZnO nanocatalysts at 100 °C for 24 h. It is suggested the reaction produces an intermediate product, which is dimethylethyl-1-phenylethyl peroxide through a radical mechanism. A small amount of benzaldehyde was observed because benzaldehyde went autoxidation to form benzoic acid with the presence of oxidation agent of TBHP during reaction. The factors affecting the catalytic activity such as gold loading, calcination treatment at 300°C, type of solvent, reaction time, reaction temperature, oxidant to substrate molar ratio, catalyst weight, and solvent volume were studied. The gold nanoparticle catalyst synthesized by deposition precipitation method using urea was characterized by XRD, HRTEM, ATR-IR, XRF, and BET and offers a very selective reaction pathway for the oxidation of ethylbenzene.
Bacterial pigments are potential substitute of chemical photosensitizer for dye-sensitized solar cell (DSSC) due to its non-toxic property and cost-effective production from microbial fermentation. Serratia nematodiphila YO1 was isolated from waterfall in Malaysia and identified using 16S ribosomal RNA. Characterization of the red pigment produced by the bacteria has confirmed the pigment as prodigiosin. Prodigiosin was produced from the fermentation of the bacteria in the presence of different oil substrates. Palm oil exhibited the best performance of cell growth and equivalent prodigiosin yield compared to olive oil and peanut oil. Prodigiosin produced with palm oil supplementation was 93 mg/l compared to 7.8 mg/l produced without supplementation, which recorded 11.9 times improvement. Specific growth rate of the cells improved 1.4 times when palm oil was supplemented in the medium. The prodigiosin pigment produced showed comparable performance as a DSSC sensitizer by displaying an open circuit voltage of 336.1 mV and a maximum short circuit current of 0.098 mV/cm2. This study stands a novelty in proving that the production of prodigiosin is favorable in the presence of palm oil substrate with high saturated fat content, which has not been studied before. This is also among the first bacterial prodigiosin tested as photosensitizer for DSSC application.
This study examined the association of various brands of NIOSH-certified N95 filtering face-piece respirators (FFR) fit with facial dimensions and gender. One hundred and thirty-five participants (77 females and 58 males) were recruited from the previous facial anthropometry study among Malaysians in 2020. Quantitative respirator fit testing of six FFR were performed using the TSI Portacount Pro+ 8038 which comprised of four exercises (bending over, talking, up-down head movement, and side to side head movement). An overall fit factor (FF) of ≥ 100 was considered a pass for each FFR. Analysis was done using T-test, Pearson's correlations, and generalised linear regression. The passing rates for the six FFR were 36.3% (Cup B), 50.4% (Trifold A), 54.1% (Duckbill A), 57.0% (Cup A), 74.1% (Trifold B), and 83.7% (Duckbill B). Both Duckbill B and Trifold B had the highest passing rates for both genders. However, certain FFR models (Cup B, Trifold A, Trifold B, and Duckbill A) fit better for participants with large facial size who were mostly males, while others (Cup A and Duckbill B) specifically fit better for those with small facial size, who were mostly females. This study showed significant positive effect of nose protrusion, nasal root and subnasale-sellion and the negative effect of menton-sellion, bigonial breadth and nose breadth on fit factors of various FFR. The results of this study emphasized the importance of choosing and designing FFR based on local anthropometry data, with careful consideration on the dimensions that affect the respirator fit. Since N95 are commonly used in the healthcare settings to prevent airborne transmission, the practice of respirator fit testing and selecting N95 with high passing rates for healthcare workers need to be emphasized.