Plant combination and rhizobacterial bioaugmentation are the modification of constructed wetlands (CWs) to promote the detoxification of leachate. In this study, characterization of leachate was carried out to ensure the maximum concentration of leachate that did not affect the plant's growth. Herein, the identification of leachate-resistant rhizobacteria is used to determine the type of bacteria that is resistant and has the potential for leachate processing in the next step. The phytodetoxification test is carried out by comparing the addition of rhizobacteria and without the addition of rhizobacteria to detox leachate parameter Chemical Oxygen Demand (COD), Biological Oxygen Demand (BOD), Total Suspended Solid (TSS), Total Nitrogen (TN), Cadmium (Cd), and Mercury (Hg). Results showed that used plants could still live in the largest leachate concentration of 100%. The rhizobacteria that were identified and bioaugmented in the reactor were Bacillus cereus, Nitrosomonas communis, and Pseudomonas aeruginosa. Phytodetoxification test by a single plant showed the efficiency ranged between 40% and 70%. The addition of rhizobacterial bioaugmentation and plant combination can improve the percentage of COD 80.47%, BOD 84.05%, TSS 80.05%, TN 75.58%, Cd 99.96%, and Hg 90%. These modifications are very influential for leachate detoxification through plant uptake and rhizodegradation processes.
This paper elucidates the capability of isolated indigenous bacteria to remove aluminium from wastewater and soil. Two indigenous species of Brochothrix thermosphacta and Vibrio alginolyticus were isolated from an aluminium-contaminated site. These two species were used to treat aluminium-containing wastewater and contaminated soil using the bioaugmentation method. B. thermosphacta showed the highest aluminium removal of 57.87 ± 0.45% while V. alginolyticus can remove aluminium up to 59.72 ± 0.33% from wastewater. For aluminium-contaminated soil, B. thermosphacta and V. alginolyticus, showed a highest removal of only 4.58 ± 0.44% and 5.48 ± 0.58%, respectively. The bioaugmentation method is more suitable to be used to treat aluminium in wastewater compared to contaminated soil. The produced biomass separation after wastewater treatment was so much easier and applicable, compared to the produced biomass handling from contaminated soil treatment. A 48.55 ± 2.45% and 40.12 ± 4.55% of aluminium can be recovered from B. thermosphacta and V. alginolyticus biomass, respectively, with 100 mg/L initial aluminium concentration in wastewater.
The greenhouse phytotoxicity experiment was conducted to analyse and assess the capability of Scirpus mucronatus (L.) in tolerating and removing petrol in contaminated soil. This research was conducted for 72 days by using 5, 10 and 30 g/kg petrol as soil contaminants. Results showed that the system planted with S. mucronatus (L.) had high potential to treat the 10 g/kg petrol-contaminated soil and had an average Total Petroleum Hydrocarbon (TPH) removal of 82.1%. At 5 and 30 g/kg petrol, the planted system removed 74.9% and 75.8% TPH, respectively. The petrol (10 g/kg) affected the plant growth positively, which was indicated by the increase in dry and wet weights throughout the research period. The removal of the TPH in the system was performed because of the interaction of plants and rhizobacteria. SEM showed that a high concentration of petrol (30 g/kg) affected the plant tissue negatively, as indicated by the altered structures of the root and stem cells. EDX results also confirmed that petrol was absorbed by the plant, as shown by the increased carbon content in the plant's root and stem after the treatment.
Phytoremediation is an environmentally friendly technique in wastewater treatment because of its sustainability, cost-effectiveness, and simplicity. This study was conducted to examine the feasibility of use of Lepironia articulata, a potential phytoremediation plant that is native to Malaysia, in remediating coffee processing mill effluent (CPME). The aim was to determine effluent concentration or contaminant load that the plant can resist, while simultaneously results in the good removal of pollutants during phytoremediation. Four brushes of L. articulata were planted individually in a pail/reactor (mentioned as reactor afterward) containing 3 kg of sand and exposed to five different concentrations of CPME (0%, 30%, 50%, 75%, and 100%). The initial chemical oxygen demand (COD) values were 510, 3100, 4200, 7290, and 8470 mg/L, respectively, and ammoniacal nitrogen (AN) concentrations were 26, 128, 225, 376, and 509 mg/L, respectively. The height, appearance, and efficiency in removing COD and AN of each plant was observed throughout the 35-day exposure period. Results showed that plants exposed to 75% CPME demonstrated better growth than those exposed to other concentrations and exhibited the highest COD and AN removal rates (85.0% and 84.0%, respectively), providing evidence that L. articulata can be used as a phytoremediation agent of CPME with an initial COD concentration of 7290 mg/L and AN concentration of 376 mg/L. This study highlights its support to the Sustainable Development Goals adopted by the United Nations, particularly the reclamation of plant biomass used as a treatment agent and conversion into biodegradable straws. Moreover, this study adds an attractive additional point of transforming waste into resource with the proposed wastewater treatment technology.
A reedbed system planted with Phragmites australis was implemented to treat chlorinated hydrocarbon-contaminated groundwater in an industrial plant area. Reedbed commissioning was conducted from July 2016 to November 2016 to treat contaminated groundwater via a pump-and-treat mechanism. Combination of horizontal and vertical reedbed systems was applied to treat 1,2-dichloroethane (1,2 DCA) under four parallel installations. The 2-acre horizontal and vertical reedbed systems were designed to treat approximately 305 m3/day of pumped groundwater. Initial concentration of 1,2 DCA was observed at 0.362 mg/L to 4320 mg/L, and the reedbed system successfully reduced the concentration up to 67.9%. The average outlet concentration was measured to be 2.08 mg/L, which was lower than the site-specific target level of 156 mg/L. Natural attenuation analysis was conducted using first-order decay kinetics, showing an average natural attenuation rate of 0.00372/year. Natural attenuation of 1,2 DCA was observed in shallow monitoring wells, which was indicated by the reduction trend of 1,2 DCA concentration, thereby confirming that the reedbed system worked well to remove 1.2 DCA from contaminated groundwater at the shallow profile.
The application of plant-based coagulants in wastewater treatment has increasingly progressed in the coagulation-flocculation process toward green economy and cleaner production. Plant-based coagulants have a potential as essential substitutes for commercially used chemical coagulants because of their natural characteristics and biodegradability. Chemical coagulants leave residues in treated water and generated sludge, which cause harm to human health and the ecosystem. Thus, the exploration of plant-based coagulants in wastewater treatment could reduce and eliminate the potential damage of chemical coagulants and promote the alternative approach for sustainable environment. The general processing steps of the end-to-end plant-based coagulant production, which includes primary, secondary, and tertiary stages, are discussed. However, this review focuses more on the extraction process using different solutions and compares the performance of different coagulants in removal activities after effluent treatment. Discussion on the arising challenges is elaborated, and approaches for plant-based coagulant research in the near future are suggested.
The contamination of aquaculture products and effluents by contaminants of emerging concern (CECs) from the direct chemical use in aquaculture activities or surrounding industries is currently an issue of increasing concern as these CECs exert acute and chronic effects on living organisms. CECs have been detected in aquaculture water, sediment, and culture species, and antibiotics, antifoulants, and disinfectants are the commonly detected groups. Through accumulation, CECs can reside in the tissue of aquaculture products and eventually consumed by humans. Currently, effluents containing CECs are discharged to the surrounding environment while producing sediments that eventually contaminate rivers as receiving bodies. The rearing (grow-out) stages of aquaculture activities are issues regarding CECs-contamination in aquaculture covering water, sediment, and aquaculture products. Proper regulations should be imposed on all aquaculturists to control chemical usage and ensure compliance to guidelines for appropriate effluent treatment. Several techniques for treating aquaculture effluents contaminated by CECs have been explored, including adsorption, wetland construction, photocatalysis, filtration, sludge activation, and sedimentation. The challenges imposed by CECs on aquaculture activities are discussed for the purpose of obtaining insights into current issues and providing future approaches for resolving associated problems. Stakeholders, such as researchers focusing on environment and aquaculture, are expected to benefit from the presented results in this article. In addition, the results may be useful in establishing aquaculture-related CECs regulations, assessing toxicity to living biota, and preventing pollution.
Dye is one of the pollutants found in water bodies because of the increased growth of the textile industry. In this study, Scirpus grossus was planted inside a constructed wetland to treat mixed dye (methylene blue and methyl orange)-containing wastewater under batch and continuous modes. The plants were exposed to various concentrations (0, 50, 75, and 100 mg/L) of mixed dye for 72 days (with hydraulic retention time of 7 days for the continuous system). Biological oxygen demand, chemical oxygen demand, total organic carbon, pH, temperature, ionic content, and plant growth parameters were measured. Results showed that S. grossus can withstand all the tested dye concentrations until the end of the treatment period. Color removal efficiencies of 86, 84, and 75% were obtained in batch mode, whereas 90%, 85%, and 79% were obtained in continuous mode for 50, 75, and 100 mg/L dye concentrations, respectively. Fourier-transform infrared analysis confirmed the transformation of dye compounds after treatment and scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy analysis showed that most of the intermediate compounds were not absorbed into plants but adsorbed onto the surface of the root structure.
Heavy metal wastes, particularly hexavalent chromium [Cr(VI)], are generated from anthropogenic activities, and their increasing abundance has been a research concern due to their toxicity, genotoxicity, carcinogenicity and mutagenicity. Exposure to these dangerous pollutants could lead to chronic infections and even mortality in humans and animals. Bioremediation using microorganisms, particularly bacteria, has gained considerable interest because it can remove contaminants naturally and is safe to the surrounding environment. Bacteria, such as Pseudomonas putida and Bacillus subtilis, can reduce the toxic Cr(VI) to the less toxic trivalent chromium Cr(III) through mechanisms including biotransformation, biosorption and bioaccumulation. These mechanisms are mostly linked to chromium reductase and nitroreductase enzymes, which are involved in the Cr(VI) reduction pathway. However, relevant data on the nitroreductase route remain insufficient. Thus, this work proposes an alternative metabolic pathway of nitroreductase, wherein nitrate activates the reaction and indirectly reduces toxic chromium. This nitroreductase pathway occurs concurrently with the chromium reduction pathway.
Chromium (Cr) is used as a mixture to improve strength and corrosion resistance. Milling and welding processes can expose workers to Cr through dermal exposure and inhalation. Cr exposure can be determined by urine testing. The purpose of this study was to analyze the concentration of Cr in urine (UCr) of workers. This study was carried out using a cross-sectional method. Sampling was conducted in the village of Mekarmaju, Bandung, Indonesia. The number of respondents included 30 blacksmiths, and the control group comprised 10 people who were not blacksmiths. Cr6+ exposure was measured using a personal sampling pump placed on the collar of the worker's shirt as a breathing zone and then analyzed using a UV-visible spectrophotometer. UCr was measured with a graphite furnace atomic absorption spectrophotometer. The measured Cr6+ concentration in the exposed working area ranged from 0.03 to 0.63 mg/m3, whereas that in non-exposed area ranged from 0.02 to 0.04 mg/m3. Results showed that 16 out of 30 blacksmiths had a UCr concentration above the biological exposure index (BEI) value, 21 had a higher value than the threshold limit value (TLV), and 22 had hazard index (HI) values > 1, which indicated that Cr has a hazardous potential in the body. The analysis of the exposed and control groups showed a significant difference with a p value of 0.000 for TLV, chronic daily intake, and UCr. These results clearly showed that Cr6+ exposure may harm the health of these workers in the future. The results obtained in this study can be used to promote workers' awareness on the potential health risk caused by Cr6+ exposure in the working environment.
This study aims to determine the distribution of organochlorine pesticide pollution in water, sediments, mollusks, and fish at Saguling Dam as baseline data of organochlorine pollution. Samples were obtained from 12 locations, with 9 and 3 sampling points inside and outside the dam, respectively. Measurement of organochlorine residues was carried out using methods of extraction, purification, evaporation, and gas chromatography. Results showed the presence of several types of organochlorine compounds, namely, lindane, aldrin, dieldrin, heptachlor, dichlorodiphenyltrichloroethane (DDT), and endosulfan. Aldrin was dominant in water (2-37 μg/L) and sediments (2-1438 μg/L), while DDT and heptachlor were dominant organochlorine compounds in mollusks (13-2758 µg/L) and fish (11-104 μg/L), respectively. Sediments demonstrated higher organochlorine concentrations than water, mollusk, and fish. The distribution of organochlorine was affected by land use around the Citarum watershed and pollutant input from tributaries.
The present study investigated the utilization of blood clam shells as a potential substitute for conventional media, as well as the influence of the acclimation time on the efficacy of an intermittent slow sand filter (ISSF) in the treatment of real domestic wastewater. ISSF was operated with 16 h on and 8 h off, focusing on the parameters of turbidity, ammonia, and phosphate. Two media combinations (only blood clam shells [CC] and sand + blood clam shells [SC]) were operated under two different acclimatization periods (14 and 28 d). Results showed that SC medium exhibited significantly higher removal of turbidity (p 0.05) removal of ammonia (23.12 ± 20.2 % vs. 16.77 ± 16.8 %) and phosphate (18.03 ± 11.96 % vs 13.48 ± 12 %). Comparing the acclimatization periods, the 28 d of acclimatization period showed higher overall performances than the 14 d. Further optimizations need to be conducted to obtain an effluent value below the national permissible limit, since the ammonia and phosphate parameters are still slightly higher. SEM analysis confirmed the formation of biofilm on both mediums after 28 d of acclimatization; with further analysis of schmutzdecke formation need to be carried out to enrich the results.
Treatment of petroleum-contaminated soil to a less toxic medium via physical and chemical treatment is too costly and requires posttreatment. This review focuses on the employment of phytoremediation and mycoremediation technologies in cleaning hydrocarbon-contaminated soil which is currently rare. It is considered environmentally beneficial and possibly cost-effective as it implements the synergistic interaction between plants and biosurfactant producing mycorrhiza to degrade hydrocarbon contaminants. This review also covers possible sources of hydrocarbon pollution in water and soil, toxicity effects, and current technologies for hydrocarbon removal and degradation. In addition to these problems, this review also discusses the challenges and opportunities of transforming the resultant treated sludge and treating plants into potential by-products for a higher quality of life for future generations.
This research analyses the performance of bacteria-assisted phytoremediation of aluminium (Al)-contaminated soil using native Indonesian plants namely, Scirpus grossus and Thypa angustifolia. A range finding test (RFT) was carried out for 14 days to obtain the tolerable Al concentration for both plants. A total of 2% and 5% (v/v) of Vibrio alginolyticus were bioaugmented during the 28-day phytoremediation test to enhance the overall Al removal. Result of the RFT showed that both plants can tolerate up to 500 mg/kg Al concentration. The addition of V. alginolyticus to the reactors resulted in a significant increment of Al removal from the contaminated soil (p < 0.05). Such addition of V. alginolyticus increased the Al removal by up to 14.0% compared with that without-bacteria addition. The highest Al removal was obtained for S. grossus with 5% V. alginolyticus with an efficiency of 35.1% from 500 mg/kg initial concertation. T. angustifolia with 500 mg/kg initial concentration showed the highest removal of 26.2% by the addition of 5% V. alginolyticus. The increase of Al removal by the bioaugmentation of V. alginolyticus was due to the interaction in the plant's rhizosphere. Exudates of both plants provided a good environment for bacteria to live in the root area. Meanwhile, the bacteria increased the bioavailability of Al to be further extracted by plants. Certain mechanisms, such as rhizostabilisation, phytostimulation and phytoextraction, were considered to be the main processes that occurred during the treatment. S. grossus and T. angustifolia displayed promising ability to act as Al hyperaccumulators with bioaccumulation factor values up to 5.308 and 3.068, respectively. Development of the design of the ex-situ soil phytoremediation reactors is suggested as a future research direction because it can significantly enhance the current obtained finding.
Bisphenol A (BPA) raises concerns among the scientific community as it is one of the most widely used compounds in industrial processes and a component of polycarbonate plastics and epoxy resins. In this review, we discuss the mechanism of BPA toxicity in food-grade plastics. Owing to its proliferation in the aqueous environment, we delved into the performance of various biological, physical, and chemical techniques for its remediation. Detailed mechanistic insights into these removal processes are provided. The toxic effects of BPA unravel as changes at the cellular level in the brain, which can result in learning difficulties, increased aggressiveness, hyperactivity, endocrine disorders, reduced fertility, and increased risk of dependence on illicit substances. Bacterial decomposition of BPA leads to new intermediates and products with lower toxicity. Processes such as membrane filtration, adsorption, coagulation, ozonation, and photocatalysis have also been shown to be efficient in aqueous-phase degradation. The breakdown mechanism of these processes is also discussed. The review demonstrates that high removal efficiency is usually achieved at the expense of high throughput. For the scalable application of BPA degradation technologies, removal efficiency needs to remain high at high throughput. We propose the need for process intensification using an integrated combination of these processes, which can solve multiple associated performance challenges.
In a slow sand filter, a biological layer consisting of alluvial mud and various types of microorganisms grows and attaches to the sand media and forms a matrix called schmutzdecke. Changes to several factors, including the quality of raw water, filtration speed, and the addition of media, affect the performance of the slow sand filter unit in producing treated water. Geotextiles can be equipped to improve the performance of a slow sand filter in removing pollutants. The selection of several factors that affect slow sand filter performance can be used as a starting point for the engineering system to determine the best pattern of performance behavior. This approach was carried out by looking at the dynamic behavior patterns of slow sand filter system performance in treating raw water. This research has not yet been conducted extensively. The dynamic behavior pattern approach to the performance of the slow sand filter unit was used to obtain the behavior model for the schmutzdecke layer on the filter. The system dynamic approach focused on treatment scenarios that can determine the behavior of the slow sand filter system. Several factors were assessed, including temperature, turbidity, nutrient concentration, algal concentration, bacteria and dissolved oxygen. Model simulation results show that the comparison of C: N: P values affected the performance of the schmutzdecke layer in removing total coli. The slow sand filter unit was capable of producing treated water with a total amount of coli equal to 0 on the C: N: P values of 85: 5.59: 1.25, respectively, and a 9 cm geotextile thickness.
The emergence of the aluminium recycling industry has led to an increase in aluminium-containing wastewater discharge to the environment. Biological treatment of metal is one of the solutions that can be provided as green technology. Screening tests showed that Brochothrix thermosphacta and Vibrio alginolyticus have the potential to remove aluminium from wastewater. Brochothrix thermosphacta removed up to 49.60%, while Vibrio alginolyticus was capable of removing up to 59.72% of 100 mg/L aluminium in acidic conditions. The removal of aluminium by V. alginolyticus was well fitted with pseudo-first-order kinetics (k1 = 0.01796/min), while B. thermosphacta showed pseudo-second-order kinetics (k2 = 0.125612 mg substrate/g adsorbent. hr) in the process of aluminium removal. V. alginolyticus had a higher rate constant under acidic conditions, while B. thermosphacta had a higher rate constant under neutral pH conditions.
In this study, two native duckweeds (Lemna minor and Azolla pinnata) were cultivated in Palm Oil Mill Effluent (POME) to extract nutrients from the effluent. Five grams of A. pinnata and 2 g of L. minor were transferred to 2 L POME (Initial concentrations: 198 mg/L COD, 4.3 mg/L nitrates, pH 9.53, 4 mg/L phosphate, 2.98 mg/L ammonia) with four different dilutions (2.5%, 5%, 10%, 15%) under greenhouse conditions. Samples of POME were taken every two days up to 10 days. Growth parameter, phosphate, ammonia, nitrates, pH, and COD were monitored within 10 days to select the most suitable growth medium for both plants. Results showed that 2.5% POME dilution had positive effect on L. minor growth and A. pinnata (wet weight increased by 8.7 g and 9.8 g, respectively), with all plants able to survive until the final day of exposure. The highest removal of ammonia was accomplished in 5% POME dilution by A. pinnata (98%) and L. minor (95.5%). The maximum phosphate removal was obtained in 10% POME dilution with 93.3% removal by A. pinnata and 86.7% by L. minor. Significant COD removal in 15% POME was obtained by L. minor (78%) and A. pinnata (66%). Both plants responded positively to the phytoremediation process, especially for A. pinnata which showed significant decreases in all parameters. The nutrient extraction by both plants from POME showed a positive effect on growth parameter, which has further promising potential to be used as animal feedstock.
Macrophytes have been widely used as agents in wastewater treatment. The involvement of plants in wastewater treatment cannot be separated from wetland utilization. As one of the green technologies in wastewater treatment plants, wetland exhibits a great performance, especially in removing nutrients from wastewater before the final discharge. It involves the use of plants and consequently produces plant biomasses as treatment byproducts. The produced plant biomasses can be utilized or converted into several valuable compounds, but related information is still limited and scattered. This review summarizes wastewater's nutrient content (macro and micronutrient) that can support plant growth and the performance of constructed wetland (CW) in performing nutrient uptake by using macrophytes as treatment agents. This paper further discusses the potential of the utilization of the produced plant biomasses as bioenergy production materials, including bioethanol, biohydrogen, biogas, and biodiesel. This paper also highlights the conversion of plant biomasses into animal feed, biochar, adsorbent, and fertilizer, which may support clean production and circular economy efforts. The presented review aims to emphasize and explore the utilization of plant biomasses and their conversion into valuable products, which may solve problems related to plant biomass handling during the adoption of CW in wastewater treatment plants.
Pilot-scale constructed wetlands planted with Scirpus grossus, were used to investigate the effects of applying a three-rhizobacterial consortium (Bacillus cereus strain NII, Bacillus subtilis strain NII and Brevibacterium sp. strain NII) on the growth of S. grossus and also on the accumulation of iron (Fe) and aluminium (Al) in S. grossus. The experiment includes constructed wetlands with the addition of 2% of the consortium rhizobacteria and without the consortium rhizobacteria addition (acting as control). During each sampling day (0, 5, 10, 15, 20, 25, 30, 42, 72 and 102), plant height, concentration of Fe and Al and sand microbial community were investigated. The results for the constructed wetland with the addition of consortium rhizobacteria showed the growth of S. grossus increased significantly at 26% and 29% for plant height and dry weight, respectively. While the accumulation of Fe and Al in S. grossus were enhanced about 48% and 19% respectively. To conclude, the addition of the rhizobacteria consortium has enhanced both the growth of S. grossus and the metal accumulation. These results suggesting that rhizobacteria has good potential to restore Fe and Al contaminated water in general and particularly for mining wastewater.