Displaying all 3 publications

Abstract:
Sort:
  1. Mohd Yusoff MZ, Hashiguchi Y, Maeda T, Wood TK
    Biochem Biophys Res Commun, 2013 Oct 4;439(4):576-9.
    PMID: 24025676 DOI: 10.1016/j.bbrc.2013.09.016
    Pseudogenes are considered to be nonfunctional genes that lack a physiological role. By screening 3985 Escherichia coli mutants using chemochromic membranes, we found four pseudogenes involved in hydrogen metabolism. Knockouts of pseudogenes ydfW and ypdJ had a defective hydrogen phenotype on glucose and formate, respectively. Also, the knockout of pseudogene yqiG formed hydrogen from formate but not from glucose. For the yqiG mutant, 100% hydrogen recovery was obtained by the complementation of YqiG via a plasmid. The knockout of pseudogene ylcE showed hydrogen deficiency in minimal media which suggested that the role of YlcE is associated with cell growth. Hence, the products of these four pseudogenes play an important physiological role in hydrogen production in E. coli.
  2. Hashiguchi Y, Zakaria MR, Toshinari M, Mohd Yusoff MZ, Shirai Y, Hassan MA
    Environ Pollut, 2021 May 15;277:116780.
    PMID: 33640825 DOI: 10.1016/j.envpol.2021.116780
    Most palm oil mills adopted conventional ponding system, including anaerobic, aerobic, facultative and algae ponds, for the treatment of palm oil mill effluent (POME). Only a few mills installed a bio-polishing plant to treat POME further before its final discharge. The present study aims to determine the quality and toxicity levels of POME final discharge from three different mills by using conventional chemical analyses and fish (Danio rerio) embryo toxicity (FET) test. The effluent derived from mill A which installed with a bio-polishing plant had lower values of BOD, COD and TSS at 45 mg/L, 104 mg/L, and 27 mg/L, respectively. Only mill A nearly met the industrial effluent discharge standard for BOD. In FET test, effluent from mill A recorded low lethality and most of the embryos were malformed after hatching (half-maximal effective concentration (EC50) = 20%). The highest toxicity was observed from the effluent of mill B and all embryos were coagulated after 24 h in samples greater than 75% of effluent (38% of half-maximal lethal concentration (LC50) at 96 h). The embryos in the effluent from mill C recorded high mortality after hatching, and the survivors were malformed after 96 h exposure (LC50 = 26%). Elemental analysis of POME final discharge samples showed Cu, Zn, and Fe concentrations were in the range of 0.10-0.32 mg/L, 0.01-0.99 mg/L, and 0.94-4.54 mg/L, respectively and all values were below the effluent permissible discharge limits. However, the present study found these metals inhibited D. rerio embryonic development at 0.12 mg/L of Cu, and 4.9 mg/L of Fe for 96 h-EC50. The present study found that bio-polishing plant installed in mill A effectively removing pollutants especially BOD and the FET test was a useful method to monitor quality and toxicity of the POME final discharge samples.
  3. Hashiguchi Y, Zakaria MR, Maeda T, Yusoff MZM, Hassan MA, Shirai Y
    Sci Total Environ, 2020 Mar 25;710:136277.
    PMID: 31923663 DOI: 10.1016/j.scitotenv.2019.136277
    Palm oil mill effluent (POME) contains complex and highly biodegradable organic matters so discharging it without appropriate treatment may lead to environmental problems. POME final discharge quality is normally determined based on conventional chemical detection such as by biological oxygen demand (BOD) and chemical oxygen demand (COD). The novelty of the present study is that the toxicity effects of the POME final discharge samples were evaluated based on whole effluent toxicity (WET) and toxicity identification evaluation (TIE) tests using Daphnia magna. The toxicity unit (TU) values were recorded to be in the range from TU = 1.1-11 obtained from WET, and the TIE manipulation tests suggested that a substantial amount of toxic compounds was contained in the POME final discharge. Phenol, 2,6-bis (1,1-dimethylethyl)- and heavy metals such as Cu and Zn were detected in all the effluents and were recognized as being the main toxicants in the POME final discharge. GC/MS analyses also successfully identified cyclic volatile methyl siloxanes; cyclotetrasiloxane, octamethyl- (D4), cyclopentasiloxane, decamethyl- (D5), cyclohexasiloxane, dodecamethyl- (D6). D4 was detected at 0.0148-0.0357 mg/L, which could be potentially toxic. The palm oil industry used only water in the form of steam to process the fruits, and the presence of these compounds might be derived from the detergents and grease used in palm oil mill cleaning and maintenance operations. An appropriate treatment process is thus required to eliminate these toxicants from the POME final discharge. It is recommended that two approaches, chemical-based monitoring as well as biological toxicity-based monitoring, should be utilized for achieving an acceptable quality of POME final discharge in the future.
Related Terms
Filters
Contact Us

Please provide feedback to Administrator ([email protected])

External Links