Solar cells are considered one of the most important and widespread solar applications in the world. However, the performance of the PV modules is significantly affected by the dust in the air. This paper, therefore, presents a comparison of an outdoor experimental study of dust effect on monocrystalline, and polycrystalline photovoltaic (PV) modules. For analysis, four 100 W PVs were installed horizontally in Sohar, Oman. For each pair of PV modules, one was left dusty due to environmental impact, and the second was cleaned daily. PV performance and environmental parameter measurements were conducted every 30 min for 35 days. The effects of dust on current, voltage, power, and energy were discussed in terms of time and normalized values. Also, cleaning methods were tested to determine the optimum one. It is found that power degradation of monocrystalline (20%) is higher compared with polycrystalline (12%) due to dust accumulation. For monocrystalline, the current, voltage, and power losses ranged between 10.0-24.0%, 2.0-3.5%, and 14.0-31.0%, respectively. However, for polycrystalline, the degradation rates were 16.88-27.92%, 0.455-0.455%, and 17.14-28.1% for current, voltage, and power losses after exposure to outdoor conditions for the same period, respectively. The dust accumulation on the PV surface found after 5 weeks is 0.493 mg/cm2, which can be considered the lowest accumulation rate compared to other Gulf countries, but which, however, leads to less energy degradation as well. It is found that water is sufficient to clean PV in the study area. However, sodium detergent as a cleaner introduced better results compared to water, especially when there is high pollution in the location.
The bi-fluid photovoltaic thermal (PVT) collector was introduced to provide more heating options along with improved cooling capabilities for the PV module. Since its introduction, this type of PVT system has been investigated thoroughly in various original works. In this review paper, we intend to put the concept and applications of this technology into question and revise the main achievements and discoveries through research and development with a focus on climatic and operational parameters. The paper encompasses a critical review of the discussed research and future directions for PVT collectors. The main utilized operational modes are discussed in detail, which are (i) water used in both channels, (ii) water in one channel and air in the other, and (iii) air in both channels. The modes were found to lead to different enhancement and performance effects for the utilized photovoltaic modules. The impact of mass flow rate was also taken by keeping one working fluid constant while varying the other to obtain its impact on the energy and exergy efficiency of the collector. In some cases, the fluids were run simultaneously and, in other cases, independently.
This paper evaluated a 1.4 kW grid-connected photovoltaic system (GCPV) using two neural network models based on experimental data for one year. The novelty of this study is to propose and compare full recurrent neural network (FRNN), and principal component analysis (PCA) models based on entire year experimental data, considering limited research conducted to predict GCPV behaviour using the two methods. The system data was collected for 12 months secondly and hourly data with 50400 samples daily. The GCPV evaluates using specific yield, energy cost, capacity factor, payback period, current, voltage, power, and efficiency. The predicted GCPV current and power using FRNN and PCA were evaluated and compared with measured values to validate results. However, the results indicated that FRNN is better in simulating the experimental results curve compared with PCA. The measured and predicted data are compared and evaluated. It is found that the GCPV is suitable and promising for the study area in terms of technical and economic evaluation with a 3.24-4.82 kWh/kWp-day yield, 21.7% capacity factor, 0.045 USD/kWh cost of energy, and 11.17 years payback period.
In the recent decades, the researchers have been focused on the use of photovoltaic thermal (PVT) systems that provide the best performance and cooling for the photovoltaic panels. In this study, a PVT system consisting of a monocrystalline PV panel and a spiral heat exchanger was connected to an underground heat exchanger that is buried at a depth of 4 m below the surface of the earth. The procedure of the current study can be considered the first of its kind in the Middle East and North Africa region (based on the researchers' knowledge). The study was carried out on agricultural land in Baghdad-Iraq during months of July and August-2022, which are considered the harshest weather conditions for this city. The heat exchanger consists of a copper tube with a length of 21 m and formed in the shape of 3U, and it was buried in the earth and connected with a PVT system. The results of the study showed that the site chosen to bury the heat exchanger (4 m deep) has a stable soil temperature at 22.5 °C. From various volumetric flow rates, a flow rate of 0.18 l/s was selected which is considered the highest flow rate that can show vibration in the PVT system which may harm the system. The practical measurements showed that the largest difference in the surface temperatures of standalone PV and PVT was around 20 °C in favor of the latter. The electrical efficiency of the studied PVT system also increased to outperform the standalone PV system by 127.3%. By comparing the results of the current study with studies of water-cooled PVT systems from the literature, it is clear that the proposed system is feasible and has an acceptable efficiency in such harsh weather conditions tested during the experiment.
Multiwalled carbon nanotubes (MWCNTs) were employed as added particles for nanofluids in this practical investigation. To identify the most appropriate nanofluid for cooling PVT systems that are functional in the extreme summer environment of Baghdad, the parameters of base fluid, surfactant, and sonication time used for mixing were examined. Water was chosen as the base fluid instead of other potential candidates such as ethylene glycol (EG), propylene glycol (PG), and heat transfer oil (HTO). Thermal conductivity and stability were important thermophysical qualities that were impacted by the chosen parameters. The nanofluid tested in Baghdad city (consisting of 0.5% MWCNTs, water, and CTAB with a sonication period of three and a quarter hours) resulted in a 119.5, 308, and 210% enhancement of thermal conductivity (TC) for water compared with EG, PG, and oil, respectively. In addition, the nanofluid-cooled PVT system had an electrical efficiency that was 88.85% higher than standalone PV technology and 44% higher than water-cooled PVT systems. Moreover, the thermal efficiency of the nanofluid-cooled PVT system was 20% higher than the water-cooled PVT system. Finally, the nanofluid-cooled PVT system displayed the least decrease in electrical efficiency and a greater thermal efficiency even when the PV panel was at its hottest at noon.