Displaying publications 101 - 120 of 503 in total

Abstract:
Sort:
  1. Preparation and characterization of low-cost activated carbon from Moringa oleifera chemically activated using ZnCl2 for the adsorption of bisphenol A
    Hussain NB, Akgül ET, Yılmaz M, Parlayıcı Ş, Hadibarata T
    Int J Phytoremediation, 2023;25(9):1199-1214.
    PMID: 36437736 DOI: 10.1080/15226514.2022.2144796
    The use of agricultural by-products such as Moringa oleifera plants is one effort to support the reduction of environmental pollution. Activated carbon produces from agricultural wastes is relatively less expensive and can replace traditional methods such as renewable as well as nonrenewable materials such as petroleum residue and coal. In this study, the removal of bisphenol A from aqueous media was studied using activated carbon produced from M. oleifera pods and peels. A batch adsorption study was carried out by varying the parameters of the adsorption process. A maximum removal percentage of 95.46% was achieved at optimum conditions of 2.5 g L-1 adsorbent dose, pH 7, 60 min contact time and 20 mg L-1 initial concentration of BPA. The BET surface areas of MOP, MOP-AC and MOP-ACZ were found to be 12.60, 4.10 and 45.96 m2/g, respectively. The experimental data were analyzed by Langmuir, Freundlich and Temkin adsorption isotherm models. Equilibrium data fitted well with the Langmuir isotherm with a maximum monolayer adsorption capacity of 20.14 mg g-1. The rates of adsorption were found to conform to the pseudo-second-order kinetics with a good correlation. The results indicate that the M. oleifera activated carbon could be employed as a low-cost alternative to commercial activated carbon in the removal of BPA from water.
    Matched MeSH terms: Biodegradation, Environmental
  2. The degradation of single-use plastics and commercially viable bioplastics in the environment: A review
    Idris SN, Amelia TSM, Bhubalan K, Lazim AMM, Zakwan NAMA, Jamaluddin MI, et al.
    Environ Res, 2023 Aug 15;231(Pt 1):115988.
    PMID: 37105296 DOI: 10.1016/j.envres.2023.115988
    Plastics have become an integral part of human life. Single-use plastics (SUPs) are disposable plastics designed to be used once then promptly discarded or recycled. This SUPs range from packaging and takeaway containers to disposable razors and hotel toiletries. Synthetic plastics, which are made of non-renewable petroleum and natural gas resources, require decades to perpetually disintegrate in nature thus contribute to plastic pollution worldwide, especially in marine environments. In response to these problems, bioplastics or bio-based and biodegradable polymers from renewable sources has been considered as an alternative. Understanding the mechanisms behind the degradation of conventional SUPs and biodegradability of their greener counterpart, bioplastics, is crucial for appropriate material selection in the future. This review aims to provide insights into the degradation or disintegration of conventional single-use plastics and the biodegradability of the different types of greener-counterparts, bioplastics, their mechanisms, and conditions. This review highlights on the biodegradation in the environments including composting systems. Here, the various types of alternative biodegradable polymers, such as bacterially biosynthesised bioplastics, natural fibre-reinforced plastics, starch-, cellulose-, lignin-, and soy-based polymers were explored. Review of past literature revealed that although bioplastics are relatively eco-friendly, their natural compositions and properties are inconsistent. Furthermore, the global plastic market for biodegradable plastics remains relatively small and require further research and commercialization efforts, especially considering the urgency of plastic and microplastic pollution as currently critical global issue. Biodegradable plastics have potential to replace conventional plastics as they show biodegradation ability under real environments, and thus intensive research on the various biodegradable plastics is needed to inform stakeholders and policy makers on the appropriate response to the gradually emerging biodegradable plastics.
    Matched MeSH terms: Biodegradation, Environmental
  3. Environmental impact and human health effects of polycyclic aromatic hydrocarbons and remedial strategies: A detailed review
    Venkatraman G, Giribabu N, Mohan PS, Muttiah B, Govindarajan VK, Alagiri M, et al.
    Chemosphere, 2024 Mar;351:141227.
    PMID: 38253087 DOI: 10.1016/j.chemosphere.2024.141227
    Polycyclic Aromatic Hydrocarbons (PAHs) profoundly impact public and environmental health. Gaining a comprehensive understanding of their intricate functions, exposure pathways, and potential health implications is imperative to implement remedial strategies and legislation effectively. This review seeks to explore PAH mobility, direct exposure pathways, and cutting-edge bioremediation technologies essential for combating the pervasive contamination of environments by PAHs, thereby expanding our foundational knowledge. PAHs, characterised by their toxicity and possession of two or more aromatic rings, exhibit diverse configurations. Their lipophilicity and remarkable persistence contribute to their widespread prevalence as hazardous environmental contaminants and byproducts. Primary sources of PAHs include contaminated food, water, and soil, which enter the human body through inhalation, ingestion, and dermal exposure. While short-term consequences encompass eye irritation, nausea, and vomiting, long-term exposure poses risks of kidney and liver damage, difficulty breathing, and asthma-like symptoms. Notably, cities with elevated PAH levels may witness exacerbation of bronchial asthma and chronic obstructive pulmonary disease (COPD). Bioremediation techniques utilising microorganisms emerge as a promising avenue to mitigate PAH-related health risks by facilitating the breakdown of these compounds in polluted environments. Furthermore, this review delves into the global concern of antimicrobial resistance associated with PAHs, highlighting its implications. The environmental effects and applications of genetically altered microbes in addressing this challenge warrant further exploration, emphasising the dynamic nature of ongoing research in this field.
    Matched MeSH terms: Biodegradation, Environmental
  4. Fulltext Advancement in Benthic Microbial Fuel Cells toward Sustainable Bioremediation and Renewable Energy Production
    Umar MF, Rafatullah M, Abbas SZ, Mohamad Ibrahim MN, Ismail N
    Int J Environ Res Public Health, 2021 Apr 06;18(7).
    PMID: 33917378 DOI: 10.3390/ijerph18073811
    Anthropogenic activities are largely responsible for the vast amounts of pollutants such as polycyclic aromatic hydrocarbons, cyanides, phenols, metal derivatives, sulphides, and other chemicals in wastewater. The excess benzene, toluene and xylene (BTX) can cause severe toxicity to living organisms in wastewater. A novel approach to mitigate this problem is the benthic microbial fuel cell (BMFC) setup to produce renewable energy and bio-remediate wastewater aromatic hydrocarbons. Several mechanisms of electrogens have been utilized for the bioremediation of BTX through BMFCs. In the future, BMFCs may be significant for chemical and petrochemical industry wastewater treatment. The distinct factors are considered to evaluate the performance of BMFCs, such as pollutant removal efficiency, power density, and current density, which are discussed by using operating parameters such as, pH, temperature and internal resistance. To further upgrade the BMFC technology, this review summarizes prototype electrode materials, the bioremediation of BTX, and their applications.
    Matched MeSH terms: Biodegradation, Environmental
  5. How plants respond to heavy metal contamination: a narrative review of proteomic studies and phytoremediation applications
    Al-Obaidi JR, Jamaludin AA, Rahman NA, Ahmad-Kamil EI
    Planta, 2024 Mar 29;259(5):103.
    PMID: 38551683 DOI: 10.1007/s00425-024-04378-2
    Heavy metal pollution caused by human activities is a serious threat to the environment and human health. Plants have evolved sophisticated defence systems to deal with heavy metal stress, with proteins and enzymes serving as critical intercepting agents for heavy metal toxicity reduction. Proteomics continues to be effective in identifying markers associated with stress response and metabolic processes. This review explores the complex interactions between heavy metal pollution and plant physiology, with an emphasis on proteomic and biotechnological perspectives. Over the last century, accelerated industrialization, agriculture activities, energy production, and urbanization have established a constant need for natural resources, resulting in environmental degradation. The widespread buildup of heavy metals in ecosystems as a result of human activity is especially concerning. Although some heavy metals are required by organisms in trace amounts, high concentrations pose serious risks to the ecosystem and human health. As immobile organisms, plants are directly exposed to heavy metal contamination, prompting the development of robust defence mechanisms. Proteomics has been used to understand how plants react to heavy metal stress. The development of proteomic techniques offers promising opportunities to improve plant tolerance to toxicity from heavy metals. Additionally, there is substantial scope for phytoremediation, a sustainable method that uses plants to extract, sequester, or eliminate contaminants in the context of changes in protein expression and total protein behaviour. Changes in proteins and enzymatic activities have been highlighted to illuminate the complex effects of heavy metal pollution on plant metabolism, and how proteomic research has revealed the plant's ability to mitigate heavy metal toxicity by intercepting vital nutrients, organic substances, and/or microorganisms.
    Matched MeSH terms: Biodegradation, Environmental
  6. Synergistic effect of Hylocereus polyrhizus (dragon fruit) peel on physicomechanical, thermal, and biodegradation properties of thermoplastic sago starch/agar composites
    Taharuddin NH, Jumaidin R, Mansor MR, Hazrati KZ, Hafila KZ, Md Yusof FA
    Int J Biol Macromol, 2024 Oct;277(Pt 1):133852.
    PMID: 39025171 DOI: 10.1016/j.ijbiomac.2024.133852
    The potential of Hylocereus polyrhizus peel (HPP) as a new eco-friendly reinforcement for thermoplastic sago starch/agar composite (TPSS/agar) was investigated. The integration of HPP into TPSS/agar composite aimed to enhance its mechanical and thermal characteristics. The study employed Fourier transform-infrared spectroscopy (FT-IR), Scanning electron microscopy (SEM), Thermogravimetric analysis (TGA), and Differential Scanning Calorimetry (DSC), as well as mechanical, physical properties and soil burial testing to analyse the composites. The results showed a favourable miscibility between the matrix and filler, while at higher concentrations of HPP, the starch granules became more visible. The tensile and impact properties of the composites improved significantly after incorporating HPP at 20 wt%, with values of 12.73 MPa and 1.87 kJ/m2, respectively. The glass transition temperature (Tg) and initial decomposition temperature (Ton) decreased with the addition of HPP. The density of the composites reduced from 1.51 ± 0.01 to 1.26 ± 0.01 g/cm3 as the HPP amount increased. The environmental properties indicated that the composites can be composted, with weight loss accelerating from 35 to 60 % and 61 to 91 % by the addition of HPP in 2- and 4-weeks' time, respectively. The study demonstrates the potential of TPSS/agar/HPP composites as eco-friendly materials for various applications.
    Matched MeSH terms: Biodegradation, Environmental
  7. Study of environmental biodegradation of LDPE films in soil using optical and scanning electron microscopy
    Mumtaz T, Khan MR, Hassan MA
    Micron, 2010 Jul;41(5):430-8.
    PMID: 20207547 DOI: 10.1016/j.micron.2010.02.008
    An outdoor soil burial test was carried out to evaluate the degradation of commercially available LDPE carrier bags in natural soil for up to 2 years. Biodegradability of low density polyethylene films in soil was monitored using both optical and scanning electron microscopy (SEM). After 7-9 months of soil exposure, microbial colonization was evident on the film surface. Exposed LDPE samples exhibit progressive changes towards degradation after 17-22 months. SEM images reveal signs of degradation such as exfoliation and formation of cracks on film leading to disintegration. The possible degradation mode and consequences on the use and disposal of LDPE films is discussed.
    Matched MeSH terms: Biodegradation, Environmental
  8. Bioregeneration of activated carbon and activated rice husk loaded with phenolic compounds: Kinetic modeling
    Ng SL, Seng CE, Lim PE
    Chemosphere, 2010 Jan;78(5):510-6.
    PMID: 20035966 DOI: 10.1016/j.chemosphere.2009.11.041
    A kinetic model consisting of first-order desorption and biodegradation processes was developed to describe the bioregeneration of phenol- and p-nitrophenol-loaded powdered activated carbon (PAC) and pyrolyzed rice husk (PRH), respectively. Different dosages of PAC and PRH were loaded with phenol or p-nitrophenol by contacting with the respective phenolic compound at various concentrations. The kinetic model was used to fit the phenol or p-nitrophenol concentration data in the bulk solution during the bioregeneration process to determine the rate constants of desorption, k(d), and biodegradation, k. The results showed that the kinetic model fitted relatively well (R(2)>0.9) to the experimental data for the phenol- and p-nitrophenol-loaded PAC as well as p-nitrophenol-loaded PRH. Comparison of the values of k(d) and k shows that k is much greater than k(d). This indicates clearly that the desorption process is the rate-determining step in bioregeneration and k(d) can be used to characterize the rate of bioregeneration. The trend of the variation of the k(d) values with the dosages of PAC or PRH used suggests that higher rate of bioregeneration can be achieved under non-excess adsorbent dosage condition.
    Matched MeSH terms: Biodegradation, Environmental
  9. Performance of combined sodium persulfate/H2O2 based advanced oxidation process in stabilized landfill leachate treatment
    Hilles AH, Abu Amr SS, Hussein RA, El-Sebaie OD, Arafa AI
    J Environ Manage, 2016 Jan 15;166:493-8.
    PMID: 26580899 DOI: 10.1016/j.jenvman.2015.10.051
    A combination of persulfate and hydrogen peroxide (S2O8(2-)/H2O2) was used to oxidizelandfill leachate. The reaction was performed under varying S2O8(2-)/H2O2 ratio (g/g), S2O8(2-)/H2O2 dosages (g/g), pH, and reaction time (minutes), so as to determine the optimum operational conditions. Results indicated that under optimum operational conditions (i.e. 120 min of oxidation using a S2O8(2-)/H2O2 ratio of 1 g/1.47 g at a persulfate and hydrogen peroxide dosage of 5.88 g/50 ml and8.63 g/50 ml respectively, at pH 11) removal of 81% COD and 83% NH3-N was achieved. In addition, the biodegradability (BOD5/COD ratio) of the leachate was improved from 0.09 to 0.17. The results obtained from the combined use of (S2O8(2-)/H2O2) were compared with those obtained with sodium persulfate only, hydrogen peroxide only and sodium persulfate followed by hydrogen peroxide. The combined method (S2O8(2-)/H2O2) achieved higher removal efficiencies for COD and NH3-N compared with the other methods using a single oxidizing agent. Additionally, the study has proved that the combination of S2O8(2-)/H2O2 is more efficient than the sequential use of sodium persulfate followed by hydrogen peroxide in advanced oxidation processes aiming at treatingstabilizedlandfill leachate.
    Matched MeSH terms: Biodegradation, Environmental
  10. A comprehensive guide of remediation technologies for oil contaminated soil - Present works and future directions
    Lim MW, Lau EV, Poh PE
    Mar Pollut Bull, 2016 Aug 15;109(1):14-45.
    PMID: 27267117 DOI: 10.1016/j.marpolbul.2016.04.023
    Oil spills result in negative impacts on the environment, economy and society. Due to tidal and waves actions, the oil spillage affects the shorelines by adhering to the soil, making it difficult for immediate cleaning of the soil. As shoreline clean-up is the most costly component of a response operation, there is a need for effective oil remediation technologies. This paper provides a review on the remediation technologies for soil contaminated with various types of oil, including diesel, crude oil, petroleum, lubricating oil, bitumen and bunker oil. The methods discussed include solvent extraction, bioremediation, phytoremediation, chemical oxidation, electrokinetic remediation, thermal technologies, ultrasonication, flotation and integrated remediation technologies. Each of these technologies was discussed, and associated with their advantages, disadvantages, advancements and future work in detail. Nonetheless, it is important to note that no single remediation technology is considered the best solution for the remediation of oil contaminated soil.

    CAPSULE: This review provides a comprehensive literature on the various remediation technologies studied in the removal of different oil types from soil.

    Matched MeSH terms: Biodegradation, Environmental
  11. Interactions of non-natural halogenated substrates with D-specific dehalogenase (DehD) mutants using in silico studies
    Sudi IY, Shamsir MS, Jamaluddin H, Wahab RA, Huyop F
    Biotechnology, biotechnological equipment, 2014 Sep 03;28(5):949-957.
    PMID: 26019583
    The D-2-haloacid dehalogenase of D-specific dehalogenase (DehD) from Rhizobium sp. RC1 catalyses the hydrolytic dehalogenation of D-haloalkanoic acids, inverting the substrate-product configuration and thereby forming the corresponding L-hydroxyalkanoic acids. Our investigations were focused on DehD mutants: R134A and Y135A. We examined the possible interactions between these mutants with haloalkanoic acids and characterized the key catalytic residues in the wild-type dehalogenase, to design dehalogenase enzyme(s) with improved potential for dehalogenation of a wider range of substrates. Three natural substrates of wild-type DehD, specifically, monochloroacetate, monobromoacetate and D,L-2,3-dichloropropionate, and eight other non-natural haloalkanoic acids substrates of DehD, namely, L-2-chloropropionate; L-2-bromopropionate; 2,2-dichloropropionate; dichloroacetate; dibromoacetate; trichloroacetate; tribromoacetate; and 3-chloropropionate, were docked into the active site of the DehD mutants R134A and Y135A, which produced altered catalytic functions. The mutants interacted strongly with substrates that wild-type DehD does not interact with or degrade. The interaction was particularly enhanced with 3-chloropropionate, in addition to monobromoacetate, monochloroacetate and D,L-2,3-dichloropropionate. In summary, DehD variants R134A and Y135A demonstrated increased propensity for binding haloalkanoic acid and were non-stereospecific towards halogenated substrates. The improved characteristics in these mutants suggest that their functionality could be further exploited and harnessed in bioremediations and biotechnological applications.
    Matched MeSH terms: Biodegradation, Environmental
  12. Filamentous fungi in Indah Water Konsortium (IWK) sewage treatment plant for biological treatment of domestic wastewater sludge
    Fakhrul-Razi A, Alam MZ, Idris A, Abd-Aziz S, Molla AH
    J Environ Sci Health A Tox Hazard Subst Environ Eng, 2002 Mar;37(3):309-20.
    PMID: 11929070
    A study was carried out to isolate and identify filamentous fungi for the treatment of domestic wastewater sludge by enhancing biodegradability, settleability and dewaterability of treated sludge using liquid state bioconversion process. A total of 70 strains of filamentous fungi were isolated from three different sources (wastewater, sewage sludge and leachate) of IWK's (Indah Water Konsortium) sewage treatment plant, Malaysia. The isolated strains were purified by conventional techniques and identified by microscopic examination. The strains isolated belonged to the genera of Penicillium, Aspergillus, Trichoderma, Spicaria and Hyaloflorae The distribution of observed isolated fungi were 41% in sewage sludge followed by 39% in wastewater and 20% in leachate. The predominant fungus was Penicillium (39 strains). The second and third most common isolates were Aspergillus (14 strains) and Trichoderma (12 strains). The other isolates were Spicaria (3 strains) and Hyaloflorae (2 strains). Three strains (WWZP1003, LZP3001, LZP3005) of Penicillium (P. corylophilum, P. waksmanii, and P. citrinum respectively), 2 strains (WWZA1006 and SS2017) of Aspergillus (A. terrues and A. flavus respectively) and one strain (SSZT2008) of Trichoderma (T. harzianum) were tentatively identified up to species level and finally verified by CABI Bioscience Identification Services, UK.
    Matched MeSH terms: Biodegradation, Environmental
  13. Fulltext Comprehensive genome analysis of a pangolin-associated Paraburkholderia fungorum provides new insights into its secretion systems and virulence
    Tan KY, Dutta A, Tan TK, Hari R, Othman RY, Choo SW
    PeerJ, 2020;8:e9733.
    PMID: 32953261 DOI: 10.7717/peerj.9733
    Background: Paraburkholderia fungorum (P. fungorum) is a Gram-negative environmental species that has been commonly used as a beneficial microorganism in agriculture as an agent for biocontrol and bioremediation. Its use in agriculture is controversial as many people believe that it could harm human health; however, there is no clear evidence to support.

    Methodology: The pangolin P. fungorum (pangolin Pf) genome has a genomic size of approximately 7.7 Mbps with N50 of 69,666 bps. Our study showed that pangolin Pf is a Paraburkholderia fungorum supported by evidence from the core genome SNP-based phylogenetic analysis and the ANI analysis. Functional analysis has shown that the presence of a considerably large number of genes related to stress response, virulence, disease, and defence. Interestingly, we identified different types of secretion systems in the genome of pangolin Pf, which are highly specialized and responsible for a bacterium's response to its environment and in physiological processes such as survival, adhesion, and adaptation. The pangolin Pf also shared some common virulence genes with the known pathogenic member of the Burkholderiales. These genes play important roles in adhesion, motility, and invasion.

    Conclusion: This study may provide better insights into the functions, secretion systems and virulence of this pangolin-associated bacterial strain. The addition of this genome sequence is also important for future comparative analysis and functional work of P. fungorum.

    Matched MeSH terms: Biodegradation, Environmental
  14. Phytoaccumulation of Zn, Pb, and Cd in Conocarpus lancifolius irrigated with wastewater: does physiological response influence heavy metal uptake?
    Rasheed F, Zafar Z, Waseem ZA, Rafay M, Abdullah M, Salam MMA, et al.
    Int J Phytoremediation, 2020;22(3):287-294.
    PMID: 31468990 DOI: 10.1080/15226514.2019.1658711
    Conocarpus lancifolius is a fast-growing and drought tolerant tree species with phytoremediation potential in arid environments. The present study was conducted to evaluate the phytoaccumulation potential under wastewater treatment. The experiment was performed in a greenhouse where 3-month-old seedlings were irrigated with industrial wastewater and growth, biomass and physiological parameters were measured. Concentrations of zinc (Zn), lead (Pb), and cadmium (Cd) in leaves, shoots, and roots along with translocation and tolerance index were also determined. The results showed that under wastewater treatment total biomass increased from 24.2 to 31.5 g, net CO2 assimilation rate increased from 9.93 to 13.3 μmol m-2 s-1, and water use efficiency increased from 1.7 to 2.42. Similarly, heavy metals (Zn, Pb, and Cd) accumulation in stem, leaves, and roots increased significantly under wastewater treatment where the highest concentration of Zn, Pb and Cd was found in roots followed by leaves and stem, respectively. Tolerance index was found >1, and translocation factor of all heavy metals was found >1. The study revealed that phytoaccumulation potential of C. lancifolius was mainly driven by improved net CO2 assimilation rate and water use efficiency.
    Matched MeSH terms: Biodegradation, Environmental
  15. Biodegradation of various homologues of palm-based methyl ester sulphonates (MES)
    Siti Afida I., Razmah G., Zulina A. M.
    Sains Malaysiana, 2016;45:949-954.
    The concern on the widespread use of surfactants is increasing worldwide as they can be potential toxicants by polluting
    the environment, with the damage formed depending on their exposure and persistence in the ecosystem. This paper
    was intended to evaluate the biodegradability of palm-based surfactant, MES, in order to establish their environmental
    friendliness. The respirometric method was used to monitor the biodegradation of various homologues of MES over 28
    days as described in the OECD 301F Manometric respirometry test method. The results showed all the MES homologues
    tested were readily biodegradable with percentage of biodegradation achieved for C12, C14 and C16 MES was 73%
    within 6 days, 66% within 8 days and 63% within 16 days, respectively, while linear alkylbenzene sulphonates (LAS)
    sample 60% biodegraded within 8 days. From the results, it can be concluded that the longer the carbon chain length, the
    lower is the biodegradability of MES as the microorganisms took longer time to degrade a longer chain surfactant. Other
    than that, the presence of aromatic structure in LAS may also extend the biodegradation process. The use of palm-based
    surfactant, i.e. MES, is more environmental friendly and can be used as an alternative to petroleum-based surfactant to
    reduce adverse environmental effects of surfactant on ecosystem.
    Matched MeSH terms: Biodegradation, Environmental
  16. Efficiency of pollutants removal in treated palm oil mill effluent (TPOME) using different concentrations of sodium alginate-immobilized Nannochloropsis sp. cells
    Emparan Q, Harun R, Sing Jye Y
    Int J Phytoremediation, 2021;23(5):454-461.
    PMID: 32976718 DOI: 10.1080/15226514.2020.1825327
    Palm oil mill effluent (POME) has high chemical oxygen demand (COD), thus requires effective treatments to environmentally benign levels before discharge. In this study, immobilized microalgae cells are used for removing pollutants in treated palm oil mill effluent (TPOME). Different ratios of microalgae beads to TPOME concentration were examined at 1:2.5, 1:5, and 1:10. The biomass concentration and COD removal were measured through a standard method. The color of the cultivated microalgae beads changed from light green to darker green after the POME treatment for 9 days, hence demonstrating that microalgae cells were successfully grown inside the beads with pH up to 9.84. The immobilized cells cultivated in the POME at 1:10 achieved a higher biomass concentration of 1.268 g/L and a COD removal percentage of 72% than other treatment ratios. The increment of the ratio of microalgae cells beads to POME concentration did not cause any improvement in COD removal efficiency. This was due to the inhibitory effect of self-shading resulting in the slow growth rate of microalgae cells which responsible for low COD removal. Therefore, this system could be a viable technology for simultaneous biomass production and POME treatment. This will contribute to research efforts toward the development of new and improved technologies in treating POME.
    Matched MeSH terms: Biodegradation, Environmental
  17. Fulltext Chitosan Epoxidized Natural Rubber Biocomposites for Sorption and Biodegradability Studies
    Raju G, Mas Haris MRH, Azura AR, Ahmed Mohamed Eid AM
    ACS Omega, 2020 Nov 10;5(44):28760-28766.
    PMID: 33195929 DOI: 10.1021/acsomega.0c04081
    The slow-release mechanism of copper into soil followed by soil biodegradation was studied using the chitosan (CTS)/epoxidized natural rubber (ENR) biocomposite. The biocomposite was prepared by homogenizing CTS in ENR50 (ENR with about 50% epoxy content) latex in the presence of curing agents and acetic acid. It was found that the adsorption property of the biocomposite was very much influenced by chitosan loading, where 20phrCTS-t-ENR biocomposite can absorb 76.31% of Cu(II) ions. The desorption study indicates that the copper (II) ion can be released at a very slow and control phase as proven by the kinetic study using zero-order, first-order, Higuchi, and Korsmeyer Peppas equations. The slow-release studies comply with the Higuchi square-root equation, indicating that the release process is diffusion-controlled. Results of desorption and biodegradation process suggest that this biocomposite has the potential use of being a slow-release matrix in the field of agriculture.
    Matched MeSH terms: Biodegradation, Environmental
  18. Fulltext Modelling of hydrogen sulfide fate and emissions in extended aeration sewage treatment plant using TOXCHEM simulations
    Zwain HM, Nile BK, Faris AM, Vakili M, Dahlan I
    Sci Rep, 2020 12 17;10(1):22209.
    PMID: 33335267 DOI: 10.1038/s41598-020-79395-8
    Odors due to the emission of hydrogen sulfide (H2S) have been a concern in the sewage treatment plants over the last decades. H2S fate and emissions from extended aeration activated sludge (EAAS) system in Muharram Aisha-sewage treatment plant (MA-STP) were studied using TOXCHEM model. Sensitivity analysis at different aeration flowrate, H2S loading rate, wastewater pH, wastewater temperature and wind speed were studied. The predicted data were validated against actual results, where all the data were validated within the limits, and the statistical evaluation of normalized mean square error (NMSE), geometric variance (VG), and correlation coefficient (R) were close to the ideal fit. The results showed that the major processes occurring in the system were degradation and emission. During summer (27 °C) and winter (12 °C), about 25 and 23%, 1 and 2%, 2 and 2%, and 72 and 73% were fated as emitted to air, discharged with effluent, sorbed to sludge, and biodegraded, respectively. At summer and winter, the total emitted concentrations of H2S were 6.403 and 5.614 ppm, respectively. The sensitivity results indicated that aeration flowrate, H2S loading rate and wastewater pH highly influenced the emission and degradation of H2S processes compared to wastewater temperature and wind speed. To conclude, TOXCHEM model successfully predicted the H2S fate and emissions in EAAS system.
    Matched MeSH terms: Biodegradation, Environmental
  19. Fulltext Statistical Design of Experimental and Bootstrap Neural Network Modelling Approach for Thermoseparating Aqueous Two-Phase Extraction of Polyhydroxyalkanoates
    Leong YK, Chang CK, Arumugasamy SK, Lan JC, Loh HS, Muhammad D, et al.
    Polymers (Basel), 2018 Jan 30;10(2).
    PMID: 30966168 DOI: 10.3390/polym10020132
    At present, polyhydroxyalkanoates (PHAs) have been considered as a promising alternative to conventional plastics due to their diverse variability in structure and rapid biodegradation. To ensure cost competitiveness in the market, thermoseparating aqueous two-phase extraction (ATPE) with the advantages of being mild and environmental-friendly was suggested as the primary isolation and purification tool for PHAs. Utilizing two-level full factorial design, this work studied the influence and interaction between four independent variables on the partitioning behavior of PHAs. Based on the experimental results, feed forward neural network (FFNN) was used to develop an empirical model of PHAs based on the ATPE thermoseparating input-output parameter. In this case, bootstrap resampling technique was used to generate more data. At the conditions of 15 wt % phosphate salt, 18 wt % ethylene oxide⁻propylene oxide (EOPO), and pH 10 without the addition of NaCl, the purification and recovery of PHAs achieved a highest yield of 93.9%. Overall, the statistical analysis demonstrated that the phosphate concentration and thermoseparating polymer concentration were the most significant parameters due to their individual influence and synergistic interaction between them on all the response variables. The final results of the FFNN model showed the ability of the model to seamlessly generalize the relationship between the input⁻output of the process.
    Matched MeSH terms: Biodegradation, Environmental
  20. Fulltext Biodegradation of Halloysite Nanotubes-Polyester Nanocomposites Exposed to Short Term Seawater Immersion
    Saharudin MS, Wei J, Shyha I, Inam F
    Polymers (Basel), 2017 Jul 28;9(8).
    PMID: 30970992 DOI: 10.3390/polym9080314
    Halloysite nanotubes (HNTs)-polyester nanocomposites with four different concentrations were produced using solution casting technique and the biodegradation effect of short-term seawater exposure (120 h) was studied. Monolithic polyester was observed to have the highest seawater absorption with 1.37%. At 0.3 wt % HNTs reinforcement, the seawater absorption dropped significantly to the lowest value of 0.77% due to increase of liquid diffusion path. For samples tested in dry conditions, the Tg, storage modulus, tensile properties and flexural properties were improved. The highest improvement of Tg was from 79.3 to 82.4 °C (increase 3.1 °C) in the case of 0.3 wt % HNTs. This can be associated with the exfoliated HNTs particles, which restrict the mobility of polymer chains and thus raised the Tg. After seawater exposure, the Tg, storage modulus, tensile properties and flexural properties of polyester and its nanocomposites were decreased. The Young's modulus of 0.3 wt % HNTs-polyester dropped 20% while monolithic polyester dropped up to 24% compared to their values in dry condition. Apart from that, 29% flexural modulus reduction was observed, which was 18% higher than monolithic polyester. In contrast, fracture toughness and surface roughness increased due to plasticization effect. The presence of various microbial communities caused gradual biodegradation on the microstructure of the polyester matrix as also evidently shown by SEM images.
    Matched MeSH terms: Biodegradation, Environmental
Related Terms
Filters
Contact Us

Please provide feedback to Administrator ([email protected])

External Links