Poor performance of wet scrubbers in rubber processing plants due to breakthrough of specific volatile organic compounds (VOCs) causes odour impact events. The performance of wet scrubbers in the rubber drying process to remove VOCs was investigated in order to determine the responsible odorants. VOC emissions originating at the inlet and outlet of wet scrubbers were quantified using gas chromatography-mass spectrometry/olfactometry (GC-MS/O). Critical VOCs were identified alongside seasonal and daily variations of those VOCs. Altogether, 80 VOCs were detected in rubber emissions with 16 classified as critical VOCs based on their chemical concentration, high odour activity value (OAV) and unpleasant odour. Volatile fatty acids (VFAs) were the dominant VOCs with seasonal variations affecting emission composition. Results demonstrated the ineffectiveness of the wet scrubbers to mitigate odorous VOCs whereas the removal of some VOCs could be improved based on their polarity and solubility. It was found that there is a correlation between the wet scrubber performance and VFAs concentration in the emissions. The findings demonstrated that combining quantitative and sensory analyses improved accuracy in identifying odorous VOCs, which can cause odour annoyance from rubber processing. A VOC identification framework was proposed using both analyses approaches.
Matched MeSH terms: Gas Chromatography-Mass Spectrometry
Durian shell (DS) was pyrolyzed in a drop-type fixed-bed reactor to study the physicochemical properties of the products. The experiment was carried out with different particle sizes (up to 5mm) and reaction temperatures (250-650°C). The highest bio-oil yield was obtained at 650°C (57.45wt%) with DS size of 1-2mm. The elemental composition and higher heating value of the feedstock, bio-oil (650°C), and bio-char (650°C) were determined and compared. The compositions of product gases were determined via gas chromatography with thermal conductivity detector. The chemical composition of bio-oil was analyzed by gas chromatography-mass spectrometry. The bio-oil produced at lower temperature yields more alcohols, whereas the bio-oil produced at higher temperature contains more aromatics and carbonyls. Bio-oil has potential to be used as liquid fuel or fine chemical precursor after further upgrading. The results further showed the potential of bio-char as a solid fuel.
Matched MeSH terms: Gas Chromatography-Mass Spectrometry
Tongkat ali commonly known as Malaysian Ginseng (Eurycoma longifolia) is a herbal root worldwide available in nutraceuticals, either as a crude powder or capsules blended with other herbal products. Herein, a multiplexed metabolomics approach based on nuclear magnetic resonance (NMR) and solid-phase microextraction combined with gas chromatography-mass spectrometry (SPME-GC-MS) was applied for authentic tongkat ali extract vs some commercial products quality control analysis. NMR metabolite fingerprinting identified 15 major metabolites mostly ascribed to sugars, organic and fatty acids in addition to quassinoids and cinnamates. Following that, multivariate analysis as the non-supervised principal component analysis (PCA) and supervised orthogonal partial least squares-discriminant analysis (OPLS-DA) were applied revealing that differences were related to fatty acids and 13,21-dihydroeurycomanone being more enriched in authentic root. SPME-GC-MS aroma profiling led to the identification of 59 volatiles belonging mainly to alcohols, aldehydes/furans and sesquiterpene hydrocarbons. Results revealed that aroma of commercial products showed relatively different profiles being rich in vanillin, maltol, and methyl octanoate. Whereas E-cinnamaldehyde, endo-borneol, terpinen-4-ol, and benzaldehyde were more associated to the authentic product. The present study shed the light for the potential of metabolomics in authentication and standardization of tongkat ali and identification of its true flavor composition.
Matched MeSH terms: Gas Chromatography-Mass Spectrometry
Degradation of amines is a significant issue allied to amine-based carbon dioxide (CO2) absorption in post-combustion CO2 capture. It becomes essential to have a detailed understanding of degradation products for advanced post-combustion CO2 capture technology. Identification and quantification of degradation products of amines help in practicability and environmental assessment of amine-based technology. Gas, liquid, and ion chromatographic techniques are the benchmark tools for qualitative and quantitative analyses of the amines and their derivatives. Among others, gas chromatography has been more in use for this specific application, especially for the identification of degradation products of amines. This review focuses on the critical elucidation of gas chromatographic analysis and development of methods to determine the amine degradation products, highlighting preparation methods for samples and selecting columns and detectors. The choice of detector, column, sample preparation, and method development are reviewed in this manuscript, keeping in view the industry and research applications. Furthermore, obtained results on the quantitative and qualitative analyses using gas chromatography are summarized with future perspectives.
In recent years, extracellular vesicles (EVs) have gained attention for their potential as biomarkers for the early diagnosis and treatment of various diseases. Traditionally, EV isolation has relied exclusively on ultracentrifugation. However, alternative enrichment methods such as size-exclusion chromatography (SEC) and polyethylene glycol-based precipitation have been introduced. This study utilized SEC as a characterization tool to assess the efficiency of EV isolation. Urinary EVs isolated from human urine using centrifugation (40,000 × g) were analyzed using an SEC column with a pore size of 1000 Å, an inner diameter of 7.8 mm, and a length of 300 mm. The EVs were detected sequentially using UV (280 nm) and fluorescence (λex/em = 550 nm/565 nm); the EVs were observed at approximately 6 min, while the proteins were observed at approximately 12 min. The repeated centrifugation enrichment steps resulted in an increase in EV peaks and a decrease in protein peaks. SEC analysis of the enriched EV samples confirmed that a four-cycle repetition of centrifugation is necessary for successful EV enrichment and removal of non-EV proteins from 40 mL of human urine.
A confirmatory and quantitative HPLC-tandem mass spectrometry (MS-MS) method for human chorionic gonadotropin hormone (hCG) at concentrations as low as 5 IU/l following immunoaffinity extraction of the glycoprotein from urine was developed. The extraction method involved retention of urinary hCG in the immunoaffinity column via specific antigen-antibody interaction. A variety of eluents were then used to quantitatively elute hCG from the immunoaffinity column. Qualitative and quantitative analysis of hCG were undertaken using MS-MS by identifying the amino acid sequence of the marker peptide betaT5 obtained from hCG by tryptic digestion and the peak areas of three product ions b(6)(+), b(9)(+) and y(11)(+), respectively.
Matched MeSH terms: Chromatography, Affinity/methods*; Chromatography, High Pressure Liquid/methods*
Nowadays, microplastic pollution is one of the globally urgent concerns as a result of discharging plastic products into the atmosphere, aquatic and soil environments. Microplastics have average size of less than 5 mm, are non-biodegradable, accumulative, and highly persistent substances. Thousands of tons of microplastics are still accumulated in various environments, posing an enormous threat to human health and living creatures. Here, we review the occurrence and analytical methods, and impact of microplastics in the environments including soil, aquatic media, and atmosphere. Analytical methods including visual observation, Fourier-transform infrared spectroscopy, Raman spectroscopy, scanning electron microscopy, and pyrolysis-gas chromatography-mass spectrometry were evaluated. We elucidated the environmental and human health impacts of microplastics with emphasis on life malfunction, immune disruption, neurotoxicity, diseases and other tangible health risks. This review also found some shortages of analytical equivalence and/or standardization, inconsistence in sampling collection and limited knowledge of microplastic toxicity. It is hopeful that the present work not only affords a more insight into the potential dangers of microplastics on human health but also urges future researches to establish new standardizations in analytical methods.
Matched MeSH terms: Gas Chromatography-Mass Spectrometry
Polycystic ovarian syndrome (PCOS) is a complicated endocrinopathy with an unclear etiology that afflicts fertility status in women. Although the underlying causes and pathophysiology of PCOS are not completely understood, it is suspected to be driven by environmental factors as well as genetic and epigenetic factors. Bisphenol A (BPA) is a weak estrogenic endocrine disruptor known to cause adverse reproductive outcomes in women. A growing relevance supports the notion that BPA may contribute to PCOS pathogenesis. Due to the indeterminate molecular mechanisms of BPA in PCOS endocrinopathy, we sought liquid chromatography with tandem mass spectrometry (LC-MS/MS), a metabolomics strategy that could generate a metabolic signature based on urinary BPA levels of PCOS and healthy individuals. Towards this, we examined urinary BPA levels in PCOS and healthy women by ELISA and performed univariate and chemometric analysis to distinguish metabolic patterns among high and low BPA in PCOS and healthy females, followed by pathway and biomarker analysis employing MetaboAnalyst 5.0. Our findings indicated aberrant levels of certain steroids, sphingolipids, and others, implying considerable disturbances in steroid hormone biosynthesis, linoleic, linolenic, sphingolipid metabolism, and various other pathways across target groups in comparison to healthy women with low BPA levels. Collectively, our findings provide insight into metabolic signatures of BPA-exposed PCOS women, which can potentially improve management strategies and precision medicine.
Knema is one of the genera in the Myristicaceae family. The genus includes 60 species in Southeast Asia and is traditionally used for treating skin disorders. Here, for the first time, the essential oil, anti-tyrosinase, and molecular docking studies of Knema intermedia were evaluated. The essential oil was obtained by hydrodistillation and fully characterized by gas chromatography (GC-FID) and gas chromatography-mass spectrometry (GC-MS). Anti-tyrosinase activity was evaluated against mushroom tyrosinase, whereas molecular docking studies were performed using Autodock vina embedded in PyRx to evaluate the binding interactions of major components. A total of 37 components (97.3%) were successfully identified in the essential oil, which was characterized by high amounts of t-muurolol (20.1%), α-copaene (14.4%), δ-cadinene (13.9%), germacrene B (9.5%), and δ-selinene (7.0%). The essential oil displayed moderate inhibitory activity towards tyrosinase with an IC50 value of 70.2 μg/mL. The best docking energy was observed with δ-selinene (-7.8 kcal/mol), and it also forms interactions with His85, His263, and His244 which are important amino acid residues of the tyrosinase receptor. Hence, this study provides valuable scientific data on K. intermedia as potential candidate for the development of natural antiaging formulations.
Matched MeSH terms: Gas Chromatography-Mass Spectrometry
In order to evaluate the frying performance of palm-based solid frying shortening against standard olein, the fresh potato chips were fried in both frying media using an open fryer. After frying the chips for 40 h in an open batch fryer, it was found that the frying quality of palm-based solid frying shortening was better than standard palm olein in terms of Free Fatty Acid (FFA) values, Total Polar Content (TPC) and Total Polymeric Material (TPM). Solid shortening gave FFA, TPC and TPM values of 0.7, 15.3 and 2.67%, respectively, whilst standard palm olein gave values for FFA, TPC and TPM of 1.2, 19.6 and 3.10%, respectively. In terms of sensory mean scores, sensory panelists preferred the color of potato chips fried in solid shortening on the first day of frying, while on the third and fifth day of frying there were no significant differences (p < 0.05) in the sensory scores of fried products in both frying mediums. However, on the fifth day of frying, panelists gave higher scores in terms of taste, flavor and crispness for potato chips fried in solid shortening. These findings show that the palm-based solid shortening is better than palm olein when used for deep fat frying in terms of FFA values, total polar content and total polymeric material, especially for starch-based products such as potato chips. The result also shows that, in terms of sensory mean scores, after frying for 40 h, the sensory panelists gave higher scores in terms of taste, flavor and crispiness for potato chips fried in palm-based solid shortening.
Matched MeSH terms: Chromatography, High Pressure Liquid
Chronic rhinosinusitis with nasal polyps (CRSwNP) is a persistent inflammation of the sinonasal mucosa. CRSwNP treatments are associated with inconsistent efficacy and recurrence of symptoms. Dynorphin 1-17 (DYN 1-17) and its fragments have been shown to modulate the immune response in various inflammatory conditions. This study aimed to investigate the effect of different pH and degrees of inflammation on DYN 1-17 metabolism in human CRSwNP tissues. DYN 1-17 was incubated with grade 3 and grade 4 inflamed tissues of CRSwNP patients at pH 5.5 and pH 7.4 over a range of incubation periods. The resulting fragments were identified using an ultra-performance liquid chromatography (UPLC) system coupled to quadrupole-time of flight (QTOF) mass spectrometry based on their accurate mass. The rate of DYN 1-17 fragmentation was slower at pH 5.5 in comparison to pH 7.4. The extent and rate of metabolism of DYN 1-17 were much lower in grade 3 inflamed tissue (31-32 fragments) than in grade 4 (34-41 fragments). N-Terminal fragments (DYN 1-15, 1-11, 1-10, and 1-6) were metabolized slower at pH 5.5 as compared to pH 7.4. DYN 1-12, 1-8, 2-10, 4-10, 5-10, and 8-14 were only observed under the inflammatory pH while DYN 5-17 and 6-17 were only identified upon incubation with grade 4 CRSwNP tissues. DYN 1-17 metabolism was significantly affected by the pH level and the severity of the inflammation of CRSwNP tissues, indicating the potential roles of DYN 1-17 and its fragments in modulating the inflammatory response and their avenue as therapeutics in future studies.
Matched MeSH terms: Chromatography, High Pressure Liquid
Metabolomics and proteomics offer significant advantages in understanding biological mechanisms at two hierarchical levels. However, conventional single omics analysis faces challenges due to the high demand for specimens and the complexity of intrinsic associations. To obtain comprehensive and accurate system biological information, we developed a multiomics analytical method called Windows Scanning Multiomics (WSM). In this method, we performed simultaneous extraction of metabolites and proteins from the same sample, resulting in a 10% increase in the coverage of the identified biomolecules. Both metabolomics and proteomics analyses were conducted by using ultrahigh-performance liquid chromatography mass spectrometry (UPLC-MS), eliminating the need for instrument conversions. Additionally, we designed an R-based program (WSM.R) to integrate mathematical and biological correlations between metabolites and proteins into a correlation network. The network created from simultaneously extracted biomolecules was more focused and comprehensive compared to those from separate extractions. Notably, we excluded six pairs of false-positive relationships between metabolites and proteins in the network established using simultaneously extracted biomolecules. In conclusion, this study introduces a novel approach for multiomics analysis and data processing that greatly aids in bioinformation mining from multiomics results. This method is poised to play an indispensable role in systems biology research.
A stability-indicating HPLC-UV method for the determination of curcumin in Curcuma longa extract and emulsion was developed. The system suitability parameters, theoretical plates (N), tailing factor (T), capacity factor (K'), height equivalent of a theoretical plate (H) and resolution (Rs) were calculated. Stress degradation studies (acid, base, oxidation, heat and UV light) of curcumin were performed in emulsion. It was found that N>6500, T<1.1, K' was 2.68-3.75, HETP about 37 and Rs was 1.8. The method was linear from 2 to 200 μg/mL with a correlation coefficient of 0.9998. The intra-day precision and accuracy for curcumin were ⩽0.87% and ⩽2.0%, while the inter-day precision and accuracy values were ⩽2.1% and ⩽-1.92. Curcumin degraded in emulsion under acid, alkali and UV light. In conclusion, the stability-indicating method could be employed to determine curcumin in bulk and emulsions.
Matched MeSH terms: Chromatography, High Pressure Liquid/methods*
The effect of deprotenizing agents on recovery of donepezil hydrochloride in the development of a simple, rapid, selective and sensitive high performance liquid chromatography method for quantification of donepezil hydrochloride in human plasma was described. The deprotenizing agents were comprised of, perchloric acid, methanol, acetonitrile, chloroform and their mixtures. The chromatographic separation was carried out using reversed phase C18 column (Agilent Eclipse Plus C18) with UV detection at 268 nm. The mobile phase was comprised of 0.01 M potassium dihydrogen phosphate buffer, methanol and acetronitrile (50:30:20, v/v) adjusted to pH 2.7 with phosphoric acid (80%). A combination of perchloric acid and methanol gave a cleaner sample with a good recovery of donepezil hydrochloride of above 96%. The method showed intraday precision and accuracy in the range of 6.82% to 1.5% and 3.13% to 1.12% respectively, while interday precision and accuracy ranged between 1.06% to 4.71% and 13.01% to 6.43% respectively. The standard calibration curve was linear from 30ng/mL to 4000ng/mL, with a correlation coefficient of 0.9965±0.0034. The retention time of donepezil was 5.9 min with a run time of 7.0 min. The method can be applied to analyze large batch plasma samples in pharmacokinetic studies.
Matched MeSH terms: Chromatography, High Pressure Liquid/methods*
Glycyrrhiza glabra L. (Fabaceae), commonly known as 'liquorice', is one of the most popular ingredients in several traditional herbal medicinal preparations, and glycyrrhizin is the major glycoside present in this plant. The content of glycyrrhizin may vary among G. glabra samples collected from various geographical origins, which may affect the therapeutic efficacy. Thus, quantification of glycyrrhizin in G. glabra samples is important.
Matched MeSH terms: Chromatography, High Pressure Liquid*
The proteome of Naja sumatrana (Equatorial spitting cobra) venom was investigated by shotgun analysis and a combination of ion-exchange chromatography and reverse phase HPLC. Shotgun analysis revealed the presence of 39 proteins in the venom while the chromatographic approach identified 37 venom proteins. The results indicated that, like other Asiatic cobra venoms, N. sumatrana contains large number of three finger toxins and phospholipases A2, which together constitute 92.1% by weight of venom protein. However, only eight of the toxins can be considered as major venom toxins. These include two phospholipases A2, three neurotoxins (two long neurotoxins and a short neurotoxin) and three cardiotoxins. The eight major toxins have relative abundance of 1.6-27.2% venom proteins and together account for 89.8% (by weight) of total venom protein. Other venom proteins identified include Zn-metalloproteinase-disintegrin, Thaicobrin, CRISP, natriuretic peptide, complement depleting factors, cobra venom factors, venom nerve growth factor and cobra serum albumin. The proteome of N. sumatrana venom is similar to proteome of other Asiatic cobra venoms but differs from that of African spitting cobra venom. Our results confirm that the main toxic action of N. sumatrana venom is neurotoxic but the large amount of cardiotoxins and phospholipases A2 are likely to contribute significantly to the overall pathophysiological action of the venom. The differences in toxin distribution between N. sumatrana venom and African spitting cobra venoms suggest possible differences in the pathophysiological actions of N. sumatrana venom and the African spitting cobra venoms, and explain why antivenom raised against Asiatic cobra venom is not effective against African spitting cobra venoms.
Matched MeSH terms: Chromatography, High Pressure Liquid; Chromatography, Ion Exchange
For the first time 5-hydroxymethyl-2-furaldehyde (HMF) was separated from crude palm oil (CPO), and its authenticity was determined using an RP-HPLC method. Separation was accomplished with isocratic elution of a mobile phase comprising water and methanol (92:8 v/v) on a Purospher Star RP-18e column (250mm×4.6mm, 5.0μm). The flow rate was adjusted to 1ml/min and detection was performed at 284nm. The method was validated, and results obtained exhibit a good recovery (95.58% to 98.39%). Assessment of precision showed that the relative standard deviations (RSD%) of retention times and peak areas of spiked samples were less than 0.59% and 2.66%, respectively. Further, the limit of detection (LOD) and LOQ were 0.02, 0.05mg/kg, respectively, and the response was linear across the applied ranges. The crude palm oil samples analysed exhibited HMF content less than 2.27mg/kg.
Matched MeSH terms: Chromatography, High Pressure Liquid/methods*
Cyclodextrin-modified micellar electrokinetic chromatography (CD-MEKC) method was developed for simultaneous enantioseparation of three imidazole drugs namely tioconazole, isoconazole and fenticonazole. Three easily available and inexpensive cyclodextrins namely 2-hydroxypropyl-β-cyclodextrin (HP-β-CD), 2-hydroxypropyl-γ-cyclodextrin (HP-γ-CD) and heptakis(2,6-di-O-methyl)-β-cyclodextrin (DM-β-CD) were evaluated to discriminate the six stereoisomers of the drugs. However, none of the three CDs gave a complete enantioseparation of the drugs. Effective enantioseparation of tioconazole, isoconazole and fenticonazole was achieved using a combination of 35 mM HP-γ-CD and 10 mM DM-β-CD as chiral selectors. The best separation using both HP-γ-CD and DM-β-CD (35 mM:10 mM) as chiral selectors were accomplished in background electrolyte (BGE) containing 35 mM phosphate buffer (pH 7.0), 50 mM sodium dodecyl sulfate (SDS) and 15% (v/v) acetonitrile at 27 kV and 30 °C with all peaks resolved in less than 15 min with resolutions, Rs 1.90-27.22 and peak efficiencies, N > 180 000. The developed method was linear over the concentration range of 25-200 mg l(-1) (r(2) > 0.998) and the detection limits (S/N = 3) of the three imidazole drugs were found to be 2.7-7.7 mg l(-1). The CD-MEKC method was successfully applied to the determination of the three imidazole drugs in spiked human urine sample and commercial cream formulation of tioconazole and isoconazole with good recovery (93.6-106.2%) and good RSDs ranging from 2.30-6.8%.
In this study, optimization of supercritical reactive extraction directly from Jatropha seeds in a high pressure batch reactor using Response Surface Methodology (RSM) coupled with Central Composite Rotatable Design (CCRD) was performed. Four primary variables (methanol to solid ratio (SSR), reaction temperature, time and CO2 initial pressure) were investigated under the proposed constraints. It was found that all variables had significant effects towards fatty acid methyl esters (FAME) yield. Moreover, three interaction effects between the variables also played a major role in influencing the final FAME yield. Optimum FAME yield at 92.0 wt.% was achieved under the following conditions: 5.9 SSR, 300°C, 12.3 min and 20 bar CO2. Final FAME product was discovered to fulfil existing international standard. Preliminary characterization analysis proved that the solid residue can be burnt as solid fuel in the form of biochar while the liquid product can be separated as specialty chemicals or burned as bio-oil for energy production.