A digit 8-shaped resonator inspired metamaterial is proposed herein for sensor applications. The resonator is surrounded by a ground frame and excited by a microstrip feedline. The measurement of the sensor can be performed using common laboratory facilities in lieu of using the waveguide, as the resonator, ground frame, and feedline are all on the same microstrip. To achieve metamaterial properties, more than one unit cell is usually utilized, whereas, in this work, a single cell was used to achieve the metamaterial characteristics. The properties of the metamaterial were investigated to find the relationship between the simulation and measurements. The proposed metamaterial sensor shows considerable sensitivity in sensor application. For the sensor application, FR4 and Rogers RO4350 materials were used as the over-layer. The sensor can measure dielectric thickness with a sensitivity of 625 MHz/mm, 468 MHz/mm, and 354 MHz/mm for the single over-layer, double over-layers, and multiple over-layers, respectively. The proposed prototype can be utilized in several applications where metamaterial characteristics are required.
Interferences and accuracy problem are one of the most talked issues in today's world for sensor technology. To deal with this contention, a microstrip framework consisting of a dual mode double negative (DNG) metamaterial based bandpass filter is presented in this article. To obtain the ultimate noise reduction bandpass filter, the proposed structure has to go through a series of development process, where the characteristics of the structure are tested to the limit. This filter is built on Rogers RT-5880 substrate with a 50Ω microstrip line. To pursue the elementary mode of resonant frequency, the ground layer of the structure is kept partially filled and a gradual analysis is executed on the prospective metamaterial (resonator) unit cell. Depending on the developed unit cell, the filter is constructed and fabricated to verify the concept, concentrating on GPS (1.55GHz), Earth Exploration-Satellite (2.70GHz) and WiMAX (3.60GHz) bands of frequencies. Moreover, the structure is investigated using Nicolson-Ross-Weir (NRW) approach to justify the metamaterial characteristics, and also tested on S-parameters, current distribution, electric and magnetic fields and quality factor. Having a propitious architecture and DNG characteristics, the proposed structure is suitable for bandpass filter for GPS, Earth Exploration-Satellite and WiMAX frequency sensing applications.
An Ultrawideband (UWB) octagonal ring-shaped parasitic resonator-based patch antenna for microwave imaging applications is presented in this study, which is constructed with a diamond-shaped radiating patch, three octagonal, rectangular slotted ring-shaped parasitic resonator elements, and partial slotting ground plane. The main goals of uses of parasitic ring-shaped elements are improving antenna performance. In the prototype, various kinds of slots on the ground plane were investigated, and especially rectangular slots and irregular zigzag slots are applied to enhance bandwidth, gain, efficiency, and radiation directivity. The optimized size of the antenna is 29 × 24 × 1.5 mm3 by using the FR-4 substrate. The overall results illustrate that the antenna has a bandwidth of 8.7 GHz (2.80 ̶ 11.50 GHz) for the reflection coefficient S11 < -10 dB with directional radiation pattern. The maximum gain of the proposed prototype is more than 5.7 dBi, and the average efficiency over the radiating bandwidth is 75%. Different design modifications are performed to attain the most favorable outcome of the proposed antenna. However, the prototype of the proposed antenna is designed and simulated in the 3D simulator CST Microwave Studio 2018 and then effectively fabricated and measured. The investigation throughout the study of the numerical as well as experimental data explicit that the proposed antenna is appropriate for the Ultrawideband-based microwave-imaging fields.
The investigation into new sources of energy with the highest efficiency which are derived from existing energy sources is a significant research area and is attracting a great deal of interest. Radio frequency (RF) energy harvesting is a promising alternative for obtaining energy for wireless devices directly from RF energy sources in the environment. An overview of the energy harvesting concept will be discussed in detail in this paper. Energy harvesting is a very promising method for the development of self-powered electronics. Many applications, such as the Internet of Things (IoT), smart environments, the military or agricultural monitoring depend on the use of sensor networks which require a large variety of small and scattered devices. The low-power operation of such distributed devices requires wireless energy to be obtained from their surroundings in order to achieve safe, self-sufficient and maintenance-free systems. The energy harvesting circuit is known to be an interface between piezoelectric and electro-strictive loads. A modern view of circuitry for energy harvesting is based on power conditioning principles that also involve AC-to-DC conversion and voltage regulation. Throughout the field of energy conversion, energy harvesting circuits often impose electric boundaries for devices, which are important for maximizing the energy that is harvested. The power conversion efficiency (PCE) is described as the ratio between the rectifier's output DC power and the antenna-based RF-input power (before its passage through the corresponding network).
This paper presents an ultra-wideband metamaterial absorber for solar harvesting in the infrared regime (220-360 THz) of the solar spectrum. The proposed absorber consists of square-shaped copper patches of different sizes imposed on a GaAs (Gallium arsenide) substrate. The design and simulation of the unit cell are performed with finite integration technique (FIT)-based simulation software. Scattering parameters are retrieved during the simulation process. The constructed design offers absorbance above 90% within a 37.89% relative bandwidth and 99.99% absorption over a vast portion of the investigated frequency range. An equivalent circuit model is presented to endorse the validity of the proposed structure. The calculated result strongly agrees with the simulated result. Symmetrical construction of the proposed unit cell reports an angular insensitivity up to a 35° oblique incidence. Post-processed simulation data confirm that the design is polarization-insensitive.
This study aimed to investigate the compact 1-bit coding metamaterial design with various conventional and cuboid shapes by analysing the bistatic scattering patterns as well as the monostatic radar cross-section for microwave applications. The construction of this metamaterial design depends on binary elements. For example, 1-bit coding metamaterial comprises two kinds of unit cell to mimic both coding particles such as '0' and '1' with 0° and 180° phase responses. This study adopted a 1 mm × 1 mm of epoxy resin fibre (FR-4) substrate material, which possesses a dielectric constant of 4.3 and tangent loss of 0.025, to construct both elements for the 1-bit coding metamaterial. All simulations were performed using the well-known Computer Simulation Technology (CST) software. The elements were selected via a trial-and-error method based on the phase response properties of the designs. On the other hand, the phase response properties from CST software were validated through the comparison of the phase response properties of both elements with the analytical data from HFSS software. Clear closure was obtained from these findings, and it was concluded that the proposed conventional coding metamaterial manifested the lowest RCS values with an increasing number of lattices. However, the cuboid-shaped design with 20 lattices demonstrated an optimised bistatic scattering pattern of -8.49 dBm2. Additionally, the monostatic RCS values were successfully reduced within the 12 to 18 GHz frequency range with -30 to -10 dBm2 values. In short, the introduced designs were suitable for the proposed application field, and this unique phenomenon is described as the novelty of this study.
In this article, we present the use of a metamaterial-incorporated microwave-based sensor with a single port network for material characterization. The proposed sensor consists of a microstrip patch layer enclosed with a dual-square-shaped metamaterial split-ring. This structure has the dimensions of 20 × 20 × 1.524 mm3 and a copper metallic layer is placed on a Rogers RT 6002 with a partial back layer as a ground. Two resonant frequencies are exhibited for applied electromagnetic interaction using a transmission line. The dual split rings increase the compactness and accumulation of the electromagnetic field on the surface of the conducting layer to improve the sensitivity of the sensor. The numerical studies are carried out using a CST high-frequency microwave simulator. The validation of the proposed sensor is performed with an equivalent circuit model in ADS and numerical high-frequency simulator HFSS. The material under test placed on the proposed sensor shows good agreement with the frequency deviation for different permittivity variations. Different substrates are analyzed as a host medium of the sensor for parametric analysis.
Metamaterial absorber (MMA) is now attracting significant interest due to its attractive applications, such as thermal detection, sound absorption, detection for explosive, military radar, wavelength detector, underwater sound absorption, and various sensor applications that are the vital part of the internet of things. This article proposes a modified square split ring resonator MMA for Ku-band sensing application, where the metamaterial structure is designed on FR-4 substrate material with a dielectric constant of 4.3 and loss tangent of 0.025. Perfect absorption is realized at 14.62 GHz and 16.30 GHz frequency bands, where peak absorption is about 99.99% for both frequency bands. The proposed structure shows 70% of the average absorption bandwidth of 420 MHz (14.42-14.84 GHz) and 480 MHz (16.06-16.54 GHz). The metamaterial property of the proposed structure is investigated for transverse electromagnetic mode (TEM) and achieved negative permittivity, permeability, and refractive index property for each absorption frequency band at 0°, 45°, and 90° polarization angles. Interference theory is also investigated to verify the absorption properties. Moreover, the permittivity sensor application is investigated to verify the sensor performance of the proposed structure. Finally, a comparison with recent works is performed, which shows that the proposed MMA can be a good candidate for Ku-band perfect absorber and sensing applications.
A miniaturized antenna employing a negative index metamaterial with modified split-ring resonator (SRR) and capacitance-loaded strip (CLS) unit cells is presented for Ultra wideband (UWB) microwave imaging applications. Four left-handed (LH) metamaterial (MTM) unit cells are located along one axis of the antenna as the radiating element. Each left-handed metamaterial unit cell combines a modified split-ring resonator (SRR) with a capacitance-loaded strip (CLS) to obtain a design architecture that simultaneously exhibits both negative permittivity and negative permeability, which ensures a stable negative refractive index to improve the antenna performance for microwave imaging. The antenna structure, with dimension of 16 × 21 × 1.6 mm³, is printed on a low dielectric FR4 material with a slotted ground plane and a microstrip feed. The measured reflection coefficient demonstrates that this antenna attains 114.5% bandwidth covering the frequency band of 3.4-12.5 GHz for a voltage standing wave ratio of less than 2 with a maximum gain of 5.16 dBi at 10.15 GHz. There is a stable harmony between the simulated and measured results that indicate improved nearly omni-directional radiation characteristics within the operational frequency band. The stable surface current distribution, negative refractive index characteristic, considerable gain and radiation properties make this proposed negative index metamaterial antenna optimal for UWB microwave imaging applications.
The design of a compact metamaterial ultra-wideband (UWB) antenna with a goal towards application in microwave imaging systems for detecting unwanted cells in human tissue, such as in cases of breast cancer, heart failure and brain stroke detection is proposed. This proposed UWB antenna is made of four metamaterial unit cells, where each cell is an integration of a modified split ring resonator (SRR), capacitive loaded strip (CLS) and wire, to attain a design layout that simultaneously exhibits both a negative magnetic permeability and a negative electrical permittivity. This design results in an astonishing negative refractive index that enables amplification of the radiated power of this reported antenna, and therefore, high antenna performance. A low-cost FR4 substrate material is used to design and print this reported antenna, and has the following characteristics: thickness of 1.6 mm, relative permeability of one, relative permittivity of 4.60 and loss tangent of 0.02. The overall antenna size is 19.36 mm × 27.72 mm × 1.6 mm where the electrical dimension is 0.20 λ × 0.28 λ × 0.016 λ at the 3.05 GHz lower frequency band. Voltage Standing Wave Ratio (VSWR) measurements have illustrated that this antenna exhibits an impedance bandwidth from 3.05 GHz to more than 15 GHz for VSWR < 2 with an average gain of 4.38 dBi throughout the operating frequency band. The simulations (both HFSS and computer simulation technology (CST)) and the measurements are in high agreement. A high correlation factor and the capability of detecting tumour simulants confirm that this reported UWB antenna can be used as an imaging sensor.
A semi-circle looped vertically omnidirectional radiation (VOR) patterned tag antenna for UHF (919-923 MHz for Malaysia) frequency is designed to overcome the impedance mismatch issue in this paper. Two impedance matching feeding strips are used in the antenna structure to tune the input impedance of the antenna. Two dipole shaped meandered lines are used to achieve a VOR pattern. The proposed antenna is designed for 23-j224 Ω chip impedance. The antenna is suitable for 'place and tag' application. A small size of 77.68×35.5 mm2 is achieved for a read range performance of 8.3 meters using Malaysia regulated maximum power transfer of 2.0 W effective radiated power (ERP).
In this paper, proposes a microwave brain imaging system to detect brain tumors using a metamaterial (MTM) loaded three-dimensional (3D) stacked wideband antenna array. The antenna is comprised of metamaterial-loaded with three substrate layers, including two air gaps. One 1 × 4 MTM array element is used in the top layer and middle layer, and one 3 × 2 MTM array element is used in the bottom layer. The MTM array elements in layers are utilized to enhance the performance concerning antenna's efficiency, bandwidth, realized gain, radiation directionality in free space and near the head model. The antenna is fabricated on cost-effective Rogers RT5880 and RO4350B substrate, and the optimized dimension of the antenna is 50 × 40 × 8.66 mm3. The measured results show that the antenna has a fractional bandwidth of 79.20% (1.37-3.16 GHz), 93% radiation efficiency, 98% high fidelity factor, 6.67 dBi gain, and adequate field penetration in the head tissue with a maximum of 0.0018 W/kg specific absorption rate. In addition, a 3D realistic tissue-mimicking head phantom is fabricated and measured to verify the performance of the antenna. Later, a nine-antenna array-based microwave brain imaging (MBI) system is implemented and investigated by using phantom model. After that, the scattering parameters are collected, analyzed, and then processed by the Iteratively Corrected delay-multiply-and-sum algorithm to detect and reconstruct the brain tumor images. The imaging results demonstrated that the implemented MBI system can successfully detect the target benign and malignant tumors with their locations inside the brain.
An inductively tuned modified split-ring resonator-based metamaterial (MTM) is presented in this article that provides multiple resonances covering S, C, X, and Ku-bands. The MTM is designed on an FR-4 substrate with a thickness of 1.5 mm and an electrical dimension of 0.063λ × 0.063λ where wavelength, λ is calculated at 2.38 GHz. The resonator part is a combination of three squared copper rings and one circular ring in which all the square rings are modified shaped, and the inner two rings are interconnected. The resonance frequency is tuned by adding inductive metal strips in parallel two vertical splits of the outer ring that causes a significant shift of resonances towards the lower frequencies and a highly effective medium ratio (EMR) of 15.75. Numerical simulation software CST microwave studio is used for the simulation and performance analysis of the proposed unit cell. The MTM unit cell exhibits six resonances of transmission coefficient (S21) at 2.38, 4.24, 5.98, 9.55, 12.1, and 14.34 GHz covering S, C, X, and Ku-bands with epsilon negative (ENG), near-zero permeability, and near-zero refractive index (NZI). The simulated result is validated by experiment with good agreement between them. The performance of the array of the unit cells is also investigated in both simulation and measurement. The equivalent circuit modeling has been accomplished using Advanced Design Software (ADS) that shows a similar S21 response compared to CST simulation. Noteworthy to mention that with the copper backplane, the same unit cell provides multiband absorption properties with four major absorption peaks of 99.6%, 95.7%, 99.9%, 92.7% with quality factors(Q-factor) of 28.4, 34.4, 23, and 32 at 3.98, 5.5, 11.73 and 13.47 GHz, respectively which can be applied for sensing and detecting purposes. The application of an array of the unit cells is investigated using it as a superstrate of an antenna that provides a 73% (average) increase of antenna gain. Due to its simple design, compact dimension with high EMR, ENG property with near-zero permeability, this multiband NZI metamaterial can be used for microwave applications, especially for multiband antenna gain enhancement.
In this article, we propose SNG (single negative) metamaterial fabricated on Mg-Zn ferrite-based flexible microwave composites. Firstly, the flexible composites are synthesized by the sol-gel method having four different molecular compositions of MgxZn(1-x)Fe2O4, which are denoted as Mg20, Mg40, Mg60, and Mg80. The structural, morphological, and microwave properties of the synthesized flexible composites are analyzed using X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and conventional dielectric assessment kit (DAK) to justify their possible application as dielectric substrate at microwave frequency regime. Thus the average grain size is found from 20 to 24 nm, and the dielectric constants are 6.01, 5.10, 4.19, and 3.28, as well as loss tangents, are 0.002, 0.004, 0.006, and 0.008 for the prepared Mg-Zn ferrites, i.e., Mg20, Mg40, Mg60, and Mg80 respectively. Besides, the prepared low-cost Mg-Zn ferrite composites exhibit high flexibility and lightweight, which makes them a potential candidate as a metamaterial substrate. Furthermore, a single negative (SNG) metamaterial unit cell is fabricated on the prepared, flexible microwave composites, and their essential electromagnetic behaviors are observed. Very good effective medium ratios (EMR) vales are obtained from 14.65 to 18.47, which ensure the compactness of the fabricated prototypes with a physical dimension of 8 × 6.5 mm2. Also, the proposed materials have shown better performances comparing with conventional FR4 and RO4533 materials, and they have covered S-, C-, X-, Ku-, and K-band of microwave frequency region. Thus, the prepared, flexible SNG metamaterials on MgxZn(1-x)Fe2O4 composites are suitable for microwave and flexible technologies.
In this research paper, an inverse double V loaded complementary square split ring resonator based double negative (DNG) metamaterial has been developed and examined numerically and experimentally. The electromagnetic (EM) properties of the proposed inverse double V-structure were calculated using computer simulation technology (CST-2019) and the finite integration technique (FIT). The designed metamaterial provides three resonance frequencies are 2.86, 5, and 8.30 GHz, covering S-, C-, and X-bands. The total size of the recommended unit cell is 8 [Formula: see text] 8 [Formula: see text] 1.524 mm3, and a high effective medium ratio (EMR) value of 13.11 was found from it. The - 10 dB bandwidths of this structure are 2.80 to 2.91, 4.76 to 5.17, and 8.05 to 8.42 GHz. The proposed structure's novelty is its small size, simple resonator structure, which provides double negative characteristics, high EMR, maximum coverage band, and required resonance frequencies. Wi-Fi network speeds are generally faster when frequencies in the 5 GHz band are used. Since the proposed structure provides a 5 GHz frequency band, hence the suggested metamaterial can be used in Wi-Fi for high bandwidth and high-speed applications. The marine radars operate in X-band, and weather radar works in S-band. Since the designed cell provides two more resonance frequencies, i.e., 2.86 GHz (S-band) and 8.30 GHz (X-band), the proposed metamaterial could be used in weather radar and marine radar. The design process and various parametric studies have been analyzed in this article. The equivalent circuit is authenticated using the advanced design system (ADS) software compared with CST simulated result. The surface current, E-field, and H-field distributions have also been analyzed. Different types of array structure, i.e., 1 [Formula: see text] 2, 2 [Formula: see text] 2, 3 [Formula: see text] 3, 4 [Formula: see text] 4, and 20 [Formula: see text] 25 is examined and validated by the measured result. The simulated and measured outcome is an excellent agreement for the inverse double V loaded CSSRR unit cell and array. We showed the overall performance of the suggested structure is better than the other structures mentioned in the paper. Since the recommended metamaterial unit cell size is small, provides desired resonance frequency, gives a large frequency band and high EMR value; hence the suggested metamaterial can be highly applicable for Radar and Wi-Fi.
A split-ring resonator (SRR)-based power tiller wheel-shaped quad-band ℇ-negative metamaterial is presented in this research article. This is a new compact metamaterial with a high effective medium ratio (EMR) designed with three modified octagonal split-ring resonators (OSRRs). The electrical dimension of the proposed metamaterial (MM) unit cell is 0.086λ × 0.086λ, where λ is the wavelength calculated at the lowest resonance frequency of 2.35 GHz. Dielectric RT6002 materials of standard thickness (1.524 mm) were used as a substrate. Computer simulation technology (CST) Microwave Studio simulator shows four resonance peaks at 2.35, 7.72, 9.23 and 10.68 GHz with magnitudes of -43.23 dB -31.05 dB, -44.58 dB and -31.71 dB, respectively. Moreover, negative permittivity (ℇ) is observed in the frequency ranges of 2.35-3.01 GHz, 7.72-8.03 GHz, 9.23-10.02 GHz and 10.69-11.81 GHz. Additionally, a negative refractive index is observed in the frequency ranges of 2.36-3.19 GHz, 7.74-7.87 GHz, 9.26-10.33 GHz and 10.70-11.81 GHz, with near-zero permeability noted in the environments of these frequency ranges. The medium effectiveness indicator effective medium ratio (EMR) of the proposed MM is an estimated 11.61 at the lowest frequency of 2.35 GHz. The simulated results of the anticipated structure are validated by authentication processes such as array orientation, HFSS and ADS for an equivalent electrical circuit model. Given its high EMR and compactness in dimensions, the presented metamaterial can be used in S-, C- and X-band wireless communication applications.
A hepta-band terahertz metamaterial absorber (MMA) with modified dual T-shaped resonators deposited on polyimide is presented for sensing applications. The proposed polarization sensitive MMA is ultra-thin (0.061 λ) and compact (0.21 λ) at its lowest operational frequency, with multiple absorption peaks at 1.89, 4.15, 5.32, 5.84, 7.04, 8.02, and 8.13 THz. The impedance matching theory and electric field distribution are investigated to understand the physical mechanism of hepta-band absorption. The sensing functionality is evaluated using a surrounding medium with a refractive index between 1 and 1.1, resulting in good Quality factor (Q) value of 117. The proposed sensor has the highest sensitivity of 4.72 THz/RIU for glucose detection. Extreme randomized tree (ERT) model is utilized to predict absorptivities for intermediate frequencies with unit cell dimensions, substrate thickness, angle variation, and refractive index values to reduce simulation time. The effectiveness of the ERT model in predicting absorption values is evaluated using the Adjusted R2 score, which is close to 1.0 for nmin = 2, demonstrating the prediction efficiency in various test cases. The experimental results show that 60% of simulation time and resources can be saved by simulating absorber design using the ERT model. The proposed MMA sensor with an ERT model has potential applications in biomedical fields such as bacterial infections, malaria, and other diseases.
Metamaterials have gained much attention due to their exciting characteristics and potential uses in constructing valuable technologies. This paper presents a double negative square resonator shape metamaterial sensor to detect the material and its thickness. An innovative double-negative metamaterial sensor for microwave sensing applications is described in this paper. It has a highly sensitive Q-factor and has good absorption characteristics approximately equal to one. For the metamaterial sensor, the recommended measurement is 20 by 20 mm. Computer simulation technology (C.S.T.) microwave studios are used to design the metamaterial structure and figure out its reflection coefficient. Various parametric analyses have been performed to optimize the design and size of the structure. The experimental and theoretical results are shown for a metamaterial sensor that is attached to five different materials such as, Polyimide, Rogers RO3010, Rogers RO4350, Rogers RT5880, and FR-4. A sensor's performance is evaluated using three different thicknesses of FR-4. There is a remarkable similarity between the measured and simulated outcomes. The sensitivity values for 2.88 GHz and 3.5 GHz are 0.66% and 0.19%, respectively, the absorption values for both frequencies are 99.9% and 98.9%, respectively, and the q-factor values are 1413.29 and 1140.16, respectively. In addition, the figure of merit (FOM) is analyzed, and its value is 934.18. Furthermore, the proposed structure has been tested against absorption sensor applications for the purpose of verifying the sensor's performance. With a high sense of sensitivity, absorption, and Q-factor, the recommended sensor can distinguish between thicknesses and materials in various applications.
In this paper, a tuned metamaterial (MTM) consisting of a symmetric split ring resonator is presented that exhibits epsilon negative (ENG), near zero permeability and refractive index properties for multiband microwave applications. The proposed metamaterial is constituted on a Rogers (RT-5880) substrate with 1.57 mm thickness and the electrical dimension of 0.14λ × 0.14λ, where wavelength, λ is calculated at 4.2 GHz. The symmetric resonating patch is subdivided into four equal and similar quartiles with two interconnecting split rings in each quartile. The quartiles are connected at the center of the substrate with a square metal strip with which four tuning metal strips are attached. These tuning metal strips are acted as spacers between four quartiles of the resonator patch. Numerical simulation of the proposed design is executed in CST microwave studio. The proposed MTM provides four resonances of transmission coefficient (S21) at 4.20 GHz, 10.14 GHz, 13.15 GHz, and 17.1 GHz covering C, X and Ku bands with negative permittivity, near zero permeability and refractive index. The calculated effective medium ratio (EMR) is 7.14 at 4.2 GHz indicates its compactness. The resonance frequencies are selective in nature which can be easily tuned by varying the length of the tuning metal stubs. The equivalent circuit of the proposed MTM is modelled in Advanced Design Software (ADS) that exhibits a similar S21 compared with CST simulation. Surface current, electric and magnetic fields are analyzed to explain the frequency tuning property and other performances of the MTM. Compact size, ENG with near zero permeability and refractive index along with frequency selectivity through tuning provides flexibility for frequency selective applications of this MTM in wireless communications.