Displaying publications 61 - 80 of 85 in total

Abstract:
Sort:
  1. Fulltext Response Surface Methodology for the Synthesis and Characterization of Bio-Oil Extracted from Biomass Waste and Upgradation Using the Rice Husk Ash Catalyst
    Irfan M, Ghalib SA, Waqas S, Khan JA, Rahman S, Faraj Mursal SN, et al.
    ACS Omega, 2023 May 23;8(20):17869-17879.
    PMID: 37251131 DOI: 10.1021/acsomega.3c00868
    Rice husk ash (RHA), a low-cost biomaterial, was utilized to form bio-oil from pyrolysis in a batch-stirred reactor, followed by its upgradation using the RHA catalyst. In the present study, the effect of temperature (ranging from 400 to 480 °C) on bio-oil production produced from RHA was studied to obtain the maximum bio-oil yield. Response surface methodology (RSM) was applied to investigate the effect of operational parameters (temperature, heating rate, and particle size) on the bio-oil yield. The results showed that a maximum bio-oil output of 20.33% was obtained at 480 °C temperature, 80 °C/min heating rate, and 200 μm particle size. Temperature and heating rate positively impact the bio-oil yield, while particle size has little effect. The overall R2 value of 0.9614 for the proposed model proved in good agreement with the experimental data. The physical properties of raw bio-oil were determined, and 1030 kg/m3 density, 12 MJ/kg calorific value, 1.40 cSt viscosity, 3 pH, and 72 mg KOH/g acid value were obtained, respectively. To enhance the characteristics of the bio-oil, upgradation was performed using the RHA catalyst through the esterification process. The upgraded bio-oil stemmed from a density of 0.98 g/cm3, an acid value of 58 mg of KOH/g, a calorific value of 16 MJ/kg, and a viscosity 10.5 cSt, respectively. The physical properties, GC-MS and FTIR, showed an improvement in the bio-oil characterization. The findings of this study indicate that RHA can be used as an alternative source for bio-oil production to create a more sustainable and cleaner environment.
  2. Fulltext Maternal Vitamin D Supplementation for the Prevention of Respiratory Tract Infections in Offspring: A Meta-Analysis
    Sulaiman Z, Noor NM, Ismail SB, Mohd Lukman ASF, Irfan M, Hussain NHN
    Korean J Fam Med, 2022 May;43(3):174-182.
    PMID: 35610964 DOI: 10.4082/kjfm.21.0029
    BACKGROUND: Vitamin D may enhance immune system function and provide a protective effect against infections. Feto-maternal circulation plays an important role in supplying the developing fetus with nutrients and antibodies for its development and health during pregnancy and for its early years of life after birth. This meta-analysis aimed to determine the effectiveness of maternal vitamin D supplementation in preventing respiratory tract infections (RTIs) in children.

    METHODS: We searched the Central and MEDLINE databases and went through all the reference lists in the related articles. We also searched for ongoing trials at http://www.who.int/ictrp/en/ and www.clinicaltrials.gov. Randomized controlled trials comparing vitamin D supplementation with a placebo or no treatment in pregnant women published in the English language up to March 2019 were included. Two reviewers extracted data independently using a predefined protocol and assessed the risk of bias using the Cochrane risk of bias tool, with differences agreed upon by consensus. The predefined primary outcome was the number of offspring who had RTIs. The secondary outcome was the presence of measurable serum immunoglobulin E levels.

    RESULTS: Three trials involving 3,224 participants (mother-child pairs) met the inclusion criteria and were included in this review. The present analysis reported that maternal supplementation with vitamin D had no effect on RTIs among children (n=1,486 offspring; risk ratio, 0.95; 95% confidence interval, 0.82-1.11; random effects; I2 statistics, 0%).

    CONCLUSION: Maternal vitamin D supplementation had no effect on RTIs in children. Therefore, consideration of other prevention methods in this regard is recommended.

  3. Fulltext Thermodynamic and spectroscopic investigation of interactions between reactive red 223 and reactive orange 122 anionic dyes and cetyltrimethyl ammonium bromide (CTAB) cationic surfactant in aqueous solution
    Irfan M, Usman M, Mansha A, Rasool N, Ibrahim M, Rana UA, et al.
    ScientificWorldJournal, 2014;2014:540975.
    PMID: 25243216 DOI: 10.1155/2014/540975
    The present study describes the conductometric and spectroscopic study of the interaction of reactive anionic dyes, namely, reactive red 223 and reactive orange 122 with the cationic surfactant cetyltrimethyl ammonium bromide (CTAB). In a systematic investigation, the electrical conductivity data was used to calculate various thermodynamic parameters such as free energy (ΔG), enthalpy (ΔH), and the entropy (ΔS) of solubilization. The trend of change in these thermodynamic quantities indicates toward the entropy driven solubilization process. Moreover, the results from spectroscopic data reveal high degree of solubilization, with strong interactions observed in the cases of both dyes and the CTAB. The spontaneous nature of solubilization and binding was evident from the observed negative values of free energies (ΔG p and ΔG b).
  4. Hemodialysis performance and anticoagulant activities of PVP-k25 and carboxylic-multiwall nanotube composite blended Polyethersulfone membrane
    Irfan M, Irfan M, Shah SM, Baig N, Saleh TA, Ahmed M, et al.
    Mater Sci Eng C Mater Biol Appl, 2019 Oct;103:109769.
    PMID: 31349444 DOI: 10.1016/j.msec.2019.109769
    Non-covalent electrostatic interaction between amide nitrogen and carbonyl carbon of shorter chain length of polyvinylpyrrolidone (PVP-k25) was developed with in-house carboxylic oxidized multiwall carbon nanotubes (O-MWCNT) and then blended with Polyethersulfone (PES) polymer. FTIR analysis was utilized to confirm bonding nature of nano-composites (NCs) of O-MWCNT/PVP-k25 and casting membranes. Non-solvent induces phase separation process developed regular finger-like channels in composite membranes whereas pristine PES exhibited spongy entities as studied by cross sectional analysis report of FESEM. Further, FESEM instrument was also utilized to observe the dispersion of O-MWCNT/PVP based nanocomposite (NCs) with PES and membranes leaching phenomena analysis. Contact angle experiments described 24% improvement of hydrophilic behaviour, leaching ratio of additives was reduced to 1.89%, whereas water flux enhanced up to 6 times. Bovine serum albumin (BSA) and lysozyme based antifouling analysis shown up to 25% improvement, whereas 84% of water flux was regained after protein fouling than pristine PES. Anticoagulant activity was reported by estimating prothrombin, thrombin, plasma re-calcification times and production of fibrinogen cluster with platelets-adhesions photographs and hemolysis experiments. Composite membranes exhibited 3.4 and 3 times better dialysis clearance ratios of urea and creatinine solutes as compared to the raw PES membrane.
  5. The anti-inflammatory and anti-nociceptive effects of Korean black ginseng
    Lee YY, Saba E, Irfan M, Kim M, Chan JY, Jeon BS, et al.
    Phytomedicine, 2019 Feb 15;54:169-181.
    PMID: 30668366 DOI: 10.1016/j.phymed.2018.09.186
    BACKGROUND: Different processing conditions alter the ginseng bioactive compounds, promoting or reducing its anti-inflammatory effects. We compared black ginseng (BG) - that have been steamed 5 times - with red ginseng (RG).

    HYPOTHESIS/ PURPOSE: To compare the anti-inflammatory activities and the anti-nociceptive properties of RG and BG.

    METHODS: Nitric Oxide (NO) and 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazoliumbromide (MTT) assay, quantitative Reverse Transcriptase-Polymerase Chain Reaction (qRT-PCR), western blot, xylene-induced ear edema, carrageenan-induced paw edema RESULTS: The ginsenoside contents were confirmed using high-performance liquid chromatography (HPLC) and has been altered through increased processing. The highest concentration of these extracts inhibited NO production to near-basal levels in lipopolysaccharide (LPS)-stimulated RAW 264.7 without exhibiting cytotoxicity. Pro-inflammatory cytokine expression at the mRNA level was investigated using qRT-PCR. Comparatively, BG exhibited better inhibition of pro-inflammatory mediators, iNOS and COX-2 and pro-inflammatory cytokines, IL-1β, IL-6 and TNF-α. Protein expression was determined using western blot analysis and BG exhibited stronger inhibition. Xylene-induced ear edema model in mice and carrageenan-induced paw edema in rats were carried out and tested with the effects of ginseng as well as dexamethasone and indomethacin - commonly used drugs. BG is a more potent anti-inflammatory agent, possesses anti-nociceptive properties, and has a strong potency comparable to the NSAIDs.

    CONCLUSION: BG has more potent anti-inflammatory and anti-nociceptive effects due to the change in ginsenoside component with increased processing.

  6. Fabrication and performance evaluation of blood compatible hemodialysis membrane using carboxylic multiwall carbon nanotubes and low molecular weight polyvinylpyrrolidone based nanocomposites
    Irfan M, Irfan M, Idris A, Baig N, Saleh TA, Nasiri R, et al.
    J Biomed Mater Res A, 2019 03;107(3):513-525.
    PMID: 30484939 DOI: 10.1002/jbm.a.36566
    This study focused to optimize the performance of polyethersulfone (PES) hemodialysis (HD) membrane using carboxylic functionalized multiwall carbon nanotubes (c-MWCNT) and lower molecular weight grade of polyvinylpyrrolidone (PVP-k30). Initially, MWCNT were chemically functionalized by acid treatment and nanocomposites (NCs) of PVP-k30 and c-MWCNT were formed and subsequently blended with PES polymer. The spectra of FTIR of the HD membranes revealed that NCs has strong hydrogen bonding and their addition to PES polymer improved the capillary system of membranes as confirmed by Field Emission Scanning Electron Microscope (FESEM) and leaching of the additive decreased to 2% and hydrophilicity improved to 22%. The pore size and porosity of NCs were also enhanced and rejection rate was achieved in the establish dialysis range (<60 kDa). The antifouling studies had shown that NCs membrane exhibited 30% less adhesion of protein with 80% flux recovery ratio. The blood compatibility assessment disclosed that NCs based membranes showed prolonged thrombin and prothrombin clotting times, lessened production of fibrinogen cluster, and greatly suppressed adhesion of blood plasma than a pristine PES membrane. The results also unveiled that PVP-k30/NCs improved the surface properties of the membrane and the urea and creatinine removal increased to 72% and 75% than pure PES membranes. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 107A: 513-525, 2019.
  7. In vitro evaluation of actively targetable superparamagnetic nanoparticles to the folate receptor positive cancer cells
    Nasiri R, Hamzehalipour Almaki J, Idris AB, Abdul Majid FA, Nasiri M, Salouti M, et al.
    Mater Sci Eng C Mater Biol Appl, 2016 Dec 01;69:1147-58.
    PMID: 27612812 DOI: 10.1016/j.msec.2016.07.076
    Engineering of a physiologically compatible, stable and targetable SPIONs-CA-FA formulation was reported. Initially fabricated superparamagnetic iron oxide nanoparticles (SPIONs) were coated with citric acid (CA) to hamper agglomeration as well as to ameliorate biocompatibility. Folic acid (FA) as a targeting agent was then conjugated to the citric acid coated SPIONs (SPIONs-CA) for targeting the specific receptors expressed on the FAR+ cancer cells. Physiochemical characterizations were then performed to assure required properties like stability, size, phase purity, surface morphology, chemical integrity and magnetic properties. In vitro evaluations (MTT assay) were performed on HeLa, HSF 1184, MDA-MB-468 and MDA-MB-231cell lines to ensure the biocompatibility of SPIONs-CA-FA. There were no morphological changes and lysis in contact with erythrocytes recorded for SPIONs-CA-FA and SPIONs-CA. High level of SPIONs-CA-FA binding to FAR+ cell lines was assured via qualitative and quantitative in vitro binding studies. Hence, SPIONs-CA-FA was introduced as a promising tool for biomedical applications like magnetic hyperthermia and drug delivery. The in vitro findings presented in this study need to be compared with those of in vivo studies.
  8. Prevalence and prediction of pressure ulcers in admitted stroke patients in a tertiary care hospital
    Farid J, Amin R, Sheikh MA, Irfan M, AlRuwaili R, Alruwaili M, et al.
    J Tissue Viability, 2022 Nov;31(4):768-775.
    PMID: 35941057 DOI: 10.1016/j.jtv.2022.07.010
    Pressure ulcer (PU) is a localized injury to the skin or underlying tissues usually over a bony prominence, which results due to pressure or pressure in combination with shear. It is an expensive health care problem that have deterring impact on the length of hospitalization and cause extra nursing care time. Moreover, PUs negatively impacts patients' health related quality of life. High PUs prevalence figures were found in specialized hospital units such as intensive care unit (ICU), orthopedics, surgery, and also in stroke patients in medical units. The major purpose of this study is to assess the frequency of pressure ulcers in stroke patients at Ayub teaching hospital. The methodology used for carrying out the research was cross-sectional study conducted during months of September, October, and November 2020. Questionnaire was used to collect the data and well-informed written consent was taken from the patients. A total of 120 stroke patients were initially included with the intention to study the frequency of PUs among them. Different age groups were taken but majority (48.3%) belonged to the age group 31-60 years. Maximum patients were hypertensive (65%), while few of them were diabetic (35%). From the results of proposed work, it is found that out of 120 stroke patients, 75.8% presented with ischemic stroke while 24.2% presented with hemorrhagic stroke. 8.3% that is 10 out of 120 stroke patients developed pressure ulcers of grade 1 (1.7%), grade 2 (1.7%), grade 3 (2.5%), and grade 4 (2.5%) mostly in the sacral region (6.7%) and also on ankle (0.8%), and shoulder (0.8%) respectively. Patients in the study group had unsatisfactory hygiene (6.7%) were malnourished (11.7%) and were not using preventive mattresses (79.2%). Those at the risk of developing pressure ulcers were not being repositioned (6.7%) and did not had awareness (10%). Prevention and treatment used in ward is 100%. Conclusively, the frequency of pressure ulcers in stroke patients was determined to be 8.3% and the most frequent localization was sacrum. The PU care in this hospital is appropriate but still could be improved further by improving risk assessment, prevention specially use of air mattress and patient education regarding PUs. The main objective of the study is to identify the frequency of PUs in stroke patients and to highlight various factors that would avoid PUs development.
  9. Fulltext A Novel Design and Development of a Strip-Fed Circularly Polarized Rectangular Dielectric Resonator Antenna for 5G NR Sub-6 GHz Band Applications
    Illahi U, Iqbal J, Irfan M, Ismail Sulaiman M, Khan MA, Rauf A, et al.
    Sensors (Basel), 2022 Jul 25;22(15).
    PMID: 35898037 DOI: 10.3390/s22155531
    In this article, a rectangular dielectric resonator antenna (RDRA) with circularly polarized (CP) response is presented for 5G NR (New Radio) Sub-6 GHz band applications. A uniquely shaped conformal metal feeding strip is proposed to excite the RDRA in higher-order mode for high gain utilization. By using the proposed feeding mechanism, the degenerate mode pair of the first higher-order, i.e., TEδ13x at 4.13 GHz and TE1δ3y, at 4.52 GHz is excited to achieve a circularly polarized response. A circular polarization over a bandwidth of ~10%, in conjunction with a wide impedance matching over a bandwidth of ~17%, were attained by the antenna. The CP antenna proposed offers a useful gain of ~6.2 dBic. The achieved CP bandwidth of the RDRA is good enough to cover the targeted 5G NR bands around 4.4−4.8 GHz, such as n79. The proposed antenna configuration is modelled and optimized using computer simulation technology (CST). A prototype was built to confirm (validate) the performance estimated through simulation. A good agreement was observed between simulated and measured results.
  10. Fulltext Green Synthesis of ZnO and Black TiO2 Materials and Their Application in Photodegradation of Organic Pollutants
    Nawaz R, Ullah H, Ghanim AAJ, Irfan M, Anjum M, Rahman S, et al.
    ACS Omega, 2023 Oct 03;8(39):36076-36087.
    PMID: 37810725 DOI: 10.1021/acsomega.3c04229
    ZnO and black TiO2 have been selected as the most efficient materials for organic pollution abatement due to their increased efficiency when compared to other materials. However, the concept of green chemistry makes it desirable to design green synthesis approaches for their production. In this study, black TiO2 was synthesized using an environmentally safe synthetic technique with glycerol as a reductant. ZnO was prepared by using ionic-liquid-based microwave-assisted extracts of Polygonum minus. To investigate the materials' potential to photodegrade organic pollutants, methylene blue (MB) and phenol were chosen as model organic pollutants. Both materials were found to exhibit spherical morphologies and a mesoporous structure and were efficient absorbers of visible light. ZnO exhibited electron-hole pair recombination lower than that of black TiO2. Black TiO2 was discovered to be an anatase phase, whereas ZnO was found to have a hexagonal wurtzite structure. In contrast to black TiO2, which had a surface area of 239.99 m2/g and a particle size of 28 nm, ZnO had a surface area of 353.11 m2/g and a particle size of 32 nm. With a degradation time of 60 min, ZnO was able to eliminate 97.50% of the 40 mg/L MB. Black TiO2, on the other hand, could reduce 90.0% of the same amount of MB in 60 min. When tested for phenol degradation, ZnO and black TiO2 activities were reduced by nearly 15 and 25%, respectively. A detailed examination of both ZnO and black TiO2 materials revealed that ZnO has more potential and versatility for the degradation of organic pollutants under visible light irradiation.
  11. Phytosociology and ecological framework of forest tree species in the Toormang Valley, Dir Lower, Hindu Kush Range, Pakistan
    Hameed T, Ahmad I, Ullah S, Subramaniyan V, Ali I, Hussain H, et al.
    Braz J Biol, 2024;84:e282479.
    PMID: 39230079 DOI: 10.1590/1519-6984.282479
    The phytosociological survey was conducted during 2018-2020. The research area was classified into five ecological zones based on habitat, physiognomy and species composition. Pc-Ord software was used for cluster analysis and four vegetation communities were established. The Quercus baloot-Quercus incana community is situated in Sair at an altitude of 1196 (mean ± SE) m altitude with a 14.1 ± 0 slope angle and contains eleven tree species. The Pinus wallichiana- Ailanthus altissima community had a relatively small number of tree species reported in Shakawlie at 1556 (mean ± SE) with a 17.5 ± 0 slope angle. The Pinus wallichiana- Quercus incana community is distributed in Wali Kandao and Mangi Kandao at altitudes of 2030.5 (mean ± SE) m and the slope angle was 19.2 ± 1.4. This community possesses a total of twenty-one tree species and is highly diverse. Similarly, the Populus alba - Platanus orientalis group was present in Banr Pate, with an altitude of 1613 (mean ± SE) m and a 16.3 slope angle. The principal component analysis (PCA) and non-metric multidimensional scaling (NMS) ordination methods were applied to study the relationships between ecological and soil variables with trees species. The NMS ordination of axis 1 was significantly correlated with Sand% (p<0.2), Nitrogen% (p<0.1) and Pb (mg/kg) (r= 0.876751, p<0.05), while the ordination of axis 2 was significantly correlated with Silt% (p<0.2), Sand% (p<0.2), Organic matter% (p<0.2), K (mg/kg) (r=0.882433, p<0.02), Fe (mg/kg)(r=0.614833, p<0.2), Ca (mg/kg) (r=0.721712, p< 0.2) and Zn (mg/kg) (r=0.609545, p<0.2). Similarly, the PCA ordination of axis 1 revealed that it was significantly correlated with phosphorus, calcium and slope angle, while that of axis 2 was significantly correlated with altitude, zinc and manganese.
  12. Exploring Acyl Thiotriazinoindole Based Pharmacophores: Design, Synthesis, and SAR Studies with Molecular Docking and Biological Activity Profiling against Urease, α-amylase, α-glucosidase, Antimicrobial, and Antioxidant Targets
    Haider MB, Saeed A, Ahmed A, Azeem M, Ismail H, Mehmood S, et al.
    Protein J, 2024 Sep 02.
    PMID: 39222239 DOI: 10.1007/s10930-024-10229-6
    A diminutive chemical library of acyl thiotriazinoindole (ATTI) based bioactive scaffolds was synthesized, instigated by taking the economical starting material Isatin, through a series of five steps. Isatin was first nitrated followed by the attachment of pentyl moiety via nucleophilic substitution reaction. The obtained compound was reacted with thiosemicarbazide to obtain thiosemicarbazone derivative, which was eventually cyclized using basic conditions in water as solvent. Finally, the reported series was obtained through reaction of nitrated thiotriazinoindole moiety with differently substituted phenacyl bromides. The synthesized compounds were characterized using NMR spectroscopy and elemental analysis. Finally, the synthesized motifs were scrutinized for their potential to impede urease, α-glucosidase, DPPH, and α-amylase. Compound 5 h with para cyano group manifested the most pivotal biological activity among all, displaying IC50 values of 29.7 ± 0.8, 20.5 ± 0.5 and 36.8 ± 3.9 µM against urease, α-glucosidase, and DPPH assay, respectively. Simultaneously, for α-amylase compound 5 g possessing a p-CH3 at phenyl ring unfolded as most active, with calculated IC50 values 90.3 ± 1.1 µM. The scaffolds were additionally gauged for their antifungal and antibacterial activity. Among the tested strains, 5d having bromo as substituent exhibited the most potent antibacterial activity, while it also demonstrated the highest potency against Aspergillus fumigatus. Other derivatives 5b, 5e, 5i, and 5j also exhibited dual inhibition against both antibacterial and antifungal strains. The interaction pattern of derivatives clearly displayed their SAR, and their docking scores were correlated with their IC50 values. In molecular docking studies, the importance of interactions like hydrogen bonding was further asserted. The electronic factors of various substituents engendered variety of interactions between the ligands and targets implying their importance in the structures of the synthesized heterocyclic scaffolds. To conclude, the synthesized compounds had satisfactory biological activity against various important targets. Further studies are therefore encouraged by attachment of different substitutions in the structure at various positions to enhance the activity of these compounds.
  13. Fulltext Synthesis, Surface Nitriding and Characterization of Ti-Nb Modified 316L Stainless Steel Alloy Using Powder Metallurgy
    Ali S, Irfan M, Muhammad Niazi U, Rani AMA, Shah I, Legutko S, et al.
    Materials (Basel), 2021 Jun 13;14(12).
    PMID: 34199244 DOI: 10.3390/ma14123270
    The powder metallurgy (PM) technique has been widely used for producing different alloy compositions by the addition of suitable reinforcements. PM is also capable of producing desireable mechanical and physical properties of the material by varying process parameters. This research investigates the addition of titanium and niobium in a 316L stainless steel matrix for potential use in the biomedical field. The increase of sintering dwell time resulted in simultaneous sintering and surface nitriding of compositions, using nitrogen as the sintering atmosphere. The developed alloy compositions were characterized using OM, FESEM, XRD and XPS techniques for quantification of the surface nitride layer and the nitrogen absorbed during sintering. The corrosion resistance and cytotoxicity assessments of the developed compositions were carried out in artificial saliva solution and human oral fibroblast cell culture, respectively. The results indicated that the nitride layer produced during sintering increased the corrosion resistance of the alloy and the developed compositions are non-cytotoxic. This newly developed alloy composition and processing technique is expected to provide a low-cost solution to implant manufacturing.
  14. Fulltext A Critical Review on Pulsed Electric Field: A Novel Technology for the Extraction of Phytoconstituents
    Ranjha MMAN, Kanwal R, Shafique B, Arshad RN, Irfan S, Kieliszek M, et al.
    Molecules, 2021 Aug 12;26(16).
    PMID: 34443475 DOI: 10.3390/molecules26164893
    Different parts of a plant (seeds, fruits, flower, leaves, stem, and roots) contain numerous biologically active compounds called "phytoconstituents" that consist of phenolics, minerals, amino acids, and vitamins. The conventional techniques applied to extract these phytoconstituents have several drawbacks including poor performance, low yields, more solvent use, long processing time, and thermally degrading by-products. In contrast, modern and advanced extraction nonthermal technologies such as pulsed electric field (PEF) assist in easier and efficient identification, characterization, and analysis of bioactive ingredients. Other advantages of PEF include cost-efficacy, less time, and solvent consumption with improved yields. This review covers the applications of PEF to obtain bioactive components, essential oils, proteins, pectin, and other important materials from various parts of the plant. Numerous studies compiled in the current evaluation concluded PEF as the best solution to extract phytoconstituents used in the food and pharmaceutical industries. PEF-assisted extraction leads to a higher yield, utilizes less solvents and energy, and it saves a lot of time compared to traditional extraction methods. PEF extraction design should be safe and efficient enough to prevent the degradation of phytoconstituents and oils.
  15. Fulltext Synthesis and Characterization of Carbon and Carbon-Nitrogen Doped Black TiO2 Nanomaterials and Their Application in Sonophotocatalytic Remediation of Treated Agro-Industrial Wastewater
    Rahman S, Nawaz R, Khan JA, Ullah H, Irfan M, Glowacz A, et al.
    Materials (Basel), 2021 Oct 18;14(20).
    PMID: 34683764 DOI: 10.3390/ma14206175
    The conventional open ponding system employed for palm oil mill agro-effluent (POME) treatment fails to lower the levels of organic pollutants to the mandatory standard discharge limits. In this work, carbon doped black TiO2 (CB-TiO2) and carbon-nitrogen co-doped black TiO2 (CNB-TiO2) were synthesized via glycerol assisted sol-gel techniques and employed for the remediation of treated palm oil mill effluent (TPOME). Both the samples were anatase phase, with a crystallite size of 11.09-22.18 nm, lower bandgap of 2.06-2.63 eV, superior visible light absorption ability, and a high surface area of 239.99-347.26 m2/g. The performance of CNB-TiO2 was higher (51.48%) compared to only (45.72%) CB-TiO2. Thus, the CNB-TiO2 is employed in sonophotocatalytic reactions. Sonophotocatalytic process based on CNB-TiO2, assisted by hydrogen peroxide (H2O2), and operated at an ultrasonication (US) frequency of 30 kHz and 40 W power under visible light irradiation proved to be the most efficient for chemical oxygen demand (COD) removal. More than 90% of COD was removed within 60 min of sonophotocatalytic reaction, producing the effluent with the COD concentration well below the stipulated permissible limit of 50 mg/L. The electrical energy required per order of magnitude was estimated to be only 177.59 kWh/m3, indicating extreme viability of the proposed process for the remediation of TPOME.
  16. Synthesis, spectral analysis and biological evaluation of 2-{[(morpholin-4-yl)ethyl]thio}-5-phenyl/aryl-1,3,4-oxadiazole derivatives
    Ur-Rehman A, Khan SG, Naqvi SAR, Ahmad M, Akhtar N, Bokhari TH, et al.
    Pak J Pharm Sci, 2021 Jan;34(1(Special)):441-446.
    PMID: 34275792
    A series of new derivatives of 4-(2-chloroethyl)morpholine hydrochloride (5) were efficiently synthesized. Briefly, different aromatic organic acids (1a-f) were refluxed to acquire respective esters (2a-f) using conc. H2SO4 as catalyst. The esters were subjected to nucleophillic substitution by monohydrated hydrazine to acquire hydrazides (3a-f). The hydrazides were cyclized with CS2 in the presence of KOH to yield corresponding oxadiazoles (4a-f). Finally, the derivatives, 6a-f, were prepared by reacting oxadiazoles (4a-f) with 5 using NaH as activator. Structures of all the derivatives were elucidated through 1D-NMR EI-MS and IR spectral data. All these molecules were subjected to antibacterial and hemolytic activities and showed good antibacterial and hemolytic potential relative to the reference standards.
  17. Performance evaluation of phosphonium based deep eutectic solvents coated cerium oxide nanoparticles for CO2 capture
    Ahmad T, Iqbal J, Bustam MA, Babar M, Tahir MB, Sagir M, et al.
    Environ Res, 2023 Apr 01;222:115314.
    PMID: 36738770 DOI: 10.1016/j.envres.2023.115314
    The critical challenge being faced by our current modern society on a global scale is to reduce the surging effects of climate change and global warming, being caused by anthropogenic emissions of CO2 in the environment. Present study reports the surface driven adsorption potential of deep eutectic solvents (DESs) surface functionalized cerium oxide nanoparticles (CeNPs) for low pressure CO2 separation. The phosphonium based DESs were prepared using tetra butyl phosphoniumbromide as hydrogen bond acceptor (HBA) and 6 acids as hydrogen bond donors (HBDs). The as-developed DESs were characterized and employed for the surface functionalization of CeNPs with their subsequent utilization in adsorption-based CO2 adsorption. The synthesis of as-prepared DESs was confirmed through FTIR measurements and absence of precipitates, revealed through visual observations. It was found that DES6 surface functionalized CeNPs demonstrated 27% higher adsorption performance for CO2 capturing. On the contrary, DES3 coated CeNPs exhibited the least adsorption progress for CO2 separation. The higher adsorption performance associated with DES6 coated CeNPs was due to enhanced surface affinity with CO2 molecules that must have facilitated the mass transport characteristics and resulted an enhancement in CO2 adsorption performance. Carboxylic groups could have generated an electric field inside the pores to attract more polarizable adsorbates including CO2, are responsible for the relatively high values of CO2 adsorption. The quadruple movement of the CO2 molecules with the electron-deficient and pluralizable nature led to the enhancement of the interactive forces between the CO2 molecules and the CeNPs decorated with the carboxylic group hydrogen bond donor rich DES. The current findings may disclose the new research horizons and theoretical guidance for reduction in the environmental effects associated with uncontrolled CO2 emission via employing DES surface coated potential CeNPs.
  18. Fulltext Effect of Hydrophilic Polymers on Complexation Efficiency of Cyclodextrins in Enhancing Solubility and Release of Diflunisal
    Bashir M, Syed HK, Asghar S, Irfan M, Almalki WH, Menshawi SA, et al.
    Polymers (Basel), 2020 Jul 15;12(7).
    PMID: 32679660 DOI: 10.3390/polym12071564
    The effects of three hydrophilic polymers, namely, carboxymethyl cellulose sodium (CMC-Na), polyvinyl alcohol (PVA) and poloxamer-188 (PXM-188) on the solubility and dissolution of diflunisal (DIF) in complexation with β-cyclodextrin (βCD) or hydroxypropyl β-cyclodextrin (HPβCD), were investigated. The kneading method was used at different drug to cyclodextrin weight ratios. Increases in solubility and drug release were observed with the DIF/βCD and DIF/HPβCD complexes. The addition of hydrophilic polymers at 2.5, 5.0 and 10.0% w/w markedly improved the complexation and solubilizing efficiency of βCD and HPβCD. Fourier-transform infrared (FTIR) showed that DIF was successfully included into the cyclodextrin cavity. Differential scanning calorimetry (DSC) and X-ray diffractometry (XRD) confirmed stronger drug amorphization and entrapment in the molecular cage of cyclodextrins. The addition of PVA, CMC-Na or PXM-188 reduced further the intensity of the DIF endothermic peak. Most of the sharp and intense peaks of DIF disappeared with the addition of hydrophilic polymers. In conclusion, PXM-188 at a weight ratio of 10.0% w/w was the best candidate in enhancing the solubility, stability and release of DIF.
  19. Fulltext Nanofiltration PVP Membrane with Gradient Cross-Linking for Efficient Polycyclic Aromatic Hydrocarbons Removal
    Ghanim AAJ, Waqas S, Zeeshan MH, Khan JA, Ghalib SA, Irfan M, et al.
    ACS Omega, 2024 Feb 06;9(5):5265-5272.
    PMID: 38343923 DOI: 10.1021/acsomega.3c05712
    Polycyclic aromatic hydrocarbons (PAHs) are persistent organic pollutants that may contaminate various water sources and pose serious dangers to human health and the environment. Due to their capacity for size-based separation, nanofiltration membranes have become efficient instruments for PAH removal. However, issues such as membrane fouling and ineffective rejection still exist. To improve PAH rejection while reducing fouling problems, this work created a new gradient cross-linking poly(vinylpyrrolidone) (PVP) nanofiltration membrane. The gradient cross-linking technique enhanced the rejection performance and antifouling characteristics of the membrane. The results demonstrated that the highest membrane flow was achieved at a 0.15% SDS-PVP membrane. There is a trade-off between membrane flux and salt rejection since salt rejection increases with SDS owing to the growth of big pores. The membrane flux was reduced for the 0.25% SDS-PVP membrane owing to poor SDS dispersion. The prepared membrane showed enhanced removal efficiencies for the removal of the PAH compounds. The PVP membrane has the potential to be used in several water treatment applications, improving water quality, and preserving the environment.
  20. Dexibuprofen loaded into nanoemulsion based gel for topical application - In vitro characterization and in vivo anti-inflammatory evaluation
    Munir R, Khan IU, Kamal Y, Asghar S, Irfan M, Alshammari A, et al.
    Colloids Surf B Biointerfaces, 2024 Nov 26;247:114407.
    PMID: 39616935 DOI: 10.1016/j.colsurfb.2024.114407
    Arthritic disease is one of the most common diseases in adults and a leading cause of joint degeneration. Dexibuprofen (DEX) is routinely used for the treatment of rheumatoid arthritis, acute postoperative pain, primary dysmenorrheal, and in lower back pain. However, it is poorly water soluble with compromised bioavailability, and hence has limited therapeutic activity. In order to overcome these issues, we studied the formulation and characterization of nanoemulsion based system i.e nanoemulgel of DEX. This study aimed to prepare topical nanoemulgel containing 2 % DEX and solubility-enhanced DEX via ternary inclusion complexation (DEX-SE-T) and to compare it with commercially available 5 % Ibuprofen gel as there is no topical formulation of DEX is available in the market currently. A pseudoternary phase diagram was constructed using the spontaneous water titration method. Blank and drug-loaded nanoemulgel were prepared using a high-speed homogenization method. All the formulations were evaluated in terms of particle size, pH, conductivity, viscosity, zeta potential, and ex vivo drug permeation. DEX loaded nanoemulgel yield enhanced in vitro skin permeation than the commercially available 5 % ibuprofen gel. The optimized nanoemulgel formulation (DEX-SE-T) was tested in in vivo anti-inflammatory models including cotton pellets-induced abdominal granuloma (chronic inflammation) and carrageenan-induced paw edema (acute inflammation). DEX-SE-T loaded nanoemulgel has improved in vivo anti-inflammatory activity as compared to ibuprofen gel. DEX-SE-T could be a promising option for effective topical treatment of inflammatory conditions.
Related Terms
    Try searching for something
Filters
Contact Us

Please provide feedback to Administrator ([email protected])

External Links