Direct recycling of aluminum waste is crucial in sustainable manufacturing to mitigate environmental impact and conserve resources. This work was carried out to study the application of hot press forging (HPF) in recycling AA6061 aluminum chip waste, aiming to optimize operating factors using Response Surface Methodology (RSM), Artificial Neural Network (ANN) and Genetic algorithm (GA) strategy to maximize the strength of recycled parts. The experimental runs were designed using Full factorial and RSM via Minitab 21 software. RSM-ANN models were employed to examine the effect of factors and their interactions on response and to predict output, while GA-RSM and GA-ANN were used for optimization. The chips of different morphology were cold compressed into billet form and then hot forged. The effect of varying forging temperature (Tp, 450-550°C), holding time (HT, 60-120 minutes), and chip surface area to volume ratio (AS:V, 15.4-52.6 mm2/mm3) on ultimate tensile strength (UTS) was examined. Maximum UTS (237.4 MPa) was achieved at 550°C, 120 minutes and 15.4 mm2/mm3 of chip's AS: V. The Tp had the largest contributing effect ratio on the UTS, followed by HT and AS:V according to ANOVA analysis. The proposed optimization process suggested 550°C, 60 minutes, and 15.4 mm2 as the optimal condition yielding the maximum UTS. The developed models' evaluation results showed that ANN (with MSE = 1.48%) outperformed RSM model. Overall, the study promotes sustainable production by demonstrating the potential of integrating RSM and ML to optimize complex manufacturing processes and improve product quality.
Tea (Camellia sinensis) is the most highly consumed beverage in the world next to water. The common way of preparation is steeping in hot water which is varying for different type of tea. We investigated the antioxidant properties of 6 type of tea leaves under different time and temperatures of extraction method used. In general, all samples tested in this study demonstrated high levels of antioxidant capacity and antioxidant activity. The results indicate that the antioxidants activity is significantly affected by time and temperature of steeping and the highest was depending on the variety. White state values, green and black teas showed different levels of antioxidants under different extraction conditions. Overall, the highest activity for white tea was in prolonged hot and in some assays prolonged hot and cold extracts, whereas for green tea the highest activity observed in prolonged cold steeping while, for black tea was in short hot water infusion. The results of this study showed the antioxidant capacity of white and green tea was greater than black tea.
This paper presents a numerical study of the thermal performance of fins mounted on the bottom wall of a horizontal channel and cooled with either pure water or an Al2O3-water nanofluid. The bottom wall of the channel is heated at a constant temperature and cooled by mixed convection of laminar flow at a relatively low temperature. The results of the numerical simulation indicate that the heat transfer rate of fins is significantly affected by the Reynolds number (Re) and the thermal conductivity of the fins. The influence of the solid volume fraction on the increase of heat transfer is more noticeable at higher values of the Re.
Of the two variants of adipose tissue, white fat is traditionally known as a lipid rich tissue which undergoes pathological expansion in obese conditions. To counter the excess accumulation of white fat in states of energy imbalance, the second and unique type of brown fat plays a key role by burning extra energy into heat through a special metabolic pathway. In addition brown fat also plays a vital role in thermoregulation in animals and newborn humans and infants. Recent progress in research areas of these two types of fat tissue has provided compelling evidence to show that they secrete a large number of chemicals that play an important role in body weight control that involves several mechanisms. Brown fat was considered absent in the adult humans until recently. But new techniques have provided ample support for its active existence. Based on the very recent data it has been suggested that brown fat can be a target organ in the treatment of obesity which can lead to exciting and informative outcomes in the future.
Using two different hydrosilylation methods, low temperature thermal and UV initiation, silicon (111) hydrogenated surfaces were functionalized in presence of an OH-terminated alkyne, a CF3-terminated alkyne and a mixed equimolar ratio of the two alkynes. XPS studies revealed that in the absence of premeditated surface radical through low temperature hydrosilylation, the surface grafting proceeded to form a Si-O-C linkage via nucleophilic reaction through the OH group of the alkyne. This led to a small increase in surface roughness as well as an increase in hydrophobicity and this effect was attributed to the surficial etching of silicon to form nanosize pores (~1-3 nm) by residual water/oxygen as a result of changes to surface polarity from the grafting. Furthermore in the radical-free thermal environment, a mix in equimolar of these two short alkynes can achieve a high contact angle of ~102°, comparable to long alkyl chains grafting reported in literature although surface roughness was relatively mild (rms = ~1 nm). On the other hand, UV initiation on silicon totally reversed the chemical linkages to predominantly Si-C without further compromising the surface roughness, highlighting the importance of surface radicals determining the reactivity of the silicon surface to the selected alkynes.
The title compound, 3,5,7-triaza-1-azoniatricyclo[3.3.1.1(3,7)]decane 2,4-dinitrophenolate monohydrate, C6H13N4+*C6H3N2O5-*H2O, the 1:1 hydrate adduct of hexamethylenetetramine (HMT) and 2,4-dinitrophenol, undergoes a temperature phase transition. In the room-temperature phase, the adduct crystallizes in the monoclinic P2(1)/m space group, whereas in the low-temperature phase, the adduct crystallizes in the triclinic P1 space group. This phase transition is reversible, with the transition temperature at 273 K, and the phase transition is governed by hydrogen bonds and weak interactions. In both these temperature-dependent polymorphs, the crystal structure is alternately layered with sheets of hexamethylenetetramine and sheets of dinitrophenol stacked along the c axis. The hexamethylenetetramine and dinitrophenol moieties are linked by intermolecular hydrogen bonds. The water molecule in the adduct plays an important role, forming O-H...O hydrogen bonds which, together with C-H...O hydrogen bonds, bridge the adducts into molecular ribbons. Extra hydrogen bonds and weak interactions exist for the low-temperature polymorph and these interconnect the molecular ribbons into a three-dimensional packing structure. Also in these two temperature-dependent polymorphs, dinitrophenol acts as a hydrogen-bond acceptor and HMT acts as a hydrogen-bond donor.
The effects of scanning rates (1, 5, 10 and 20 degrees C/min) on the DSC cooling profiles of 11 vegetable oils have been determined in order to monitor peak transition temperatures, onset temperatures and crystallisation enthalpies. Triacylglycerol (TAG) profiles and iodine value analyses were used to complement the DSC data. The melted samples exhibited complicated crystallising exotherms. As the cooling rate increased, the crystallisation temperature decreased and the breadth of the crystallisation exotherm on cooling from the melt increased. In addition, the intensity of the exothermic peak increased somewhat when the cooling rate was increased. At slow cooling rates, TAG had more time to interact. It is conceivable that, at a low cooling rate (1 degree C/min), a prominent exotherm would be observed on crystallisation of vegetable oils and fats. The occurrence of one exotherm upon cooling indicated the co-crystallisation of the TAG upon slow cooling. On the basis of the corollary results obtained, vegetable oils may be differentiated by their onset temperature (Ton) values in the DSC cooling curves. Generally, there was a shift of Ton toward lower values with increasing cooling rates.
Iban categories of hot and cold are examined in the context of humoral medical systems in southeast Asia. These categories are more than binary and oppositional: they are also contradictory and can only be understood in terms of their capacity for transformation in 'depth'. Analysis of the Iban epistemology of temperature sensation reveals the limitations of reductionist empirical approaches to hot and cold. Illness is apprehended, at one level, in terms of unusual conjunctions of opposite temperatures which signify a deeper disturbance in the relationship between body and soul, humans and spirits. Iban therapy redefines and relocates these categories in their proper place and at their appropriate level. It progresses from hot lay treatments to cool ritual treatments, yet cannot be accounted for within a limited framework of homeostatic balance. This paper develops an ethnographically grounded definition of humoralism which emphasizes non-reductive logic, cultural practice and transformation. The key element, transformation, is defined as a transition between categories and a shift in the level of interpretation which fundamentally alter the Iban experience of body and illness.
Heat pipes are widely used in various industries such as automotive, electronics, and many more. Heat pipes are used as cooling devices for electronic parts in machines that emit a large amount of heat, which can damage the devices. The heat pipes used in this investigation are loop heat pipes. These pipes can transport heat over a long distance and operate against gravity. The working fluid used in this investigation is nanofluid. Nanofluid is one of the types of working fluid that is considered to have better thermal performance than conventional fluids. Nanofluid is made of nanoparticles with base-fluid. This investigation studies the thermal performance of loop heat pipes using different types of nanofluids. Nanofluid fluids used in this study are diamond nanofluid, aluminium oxide nanofluid and silica oxide nanofluid. The effect of mass concentration of nanoparticles in the base-fluid is also studied. The results showed that as the mass concentration of nanofluids increased, the thermal resistance for diamond nanofluid and aluminium oxide nanofluid decreased, but the opposite occurred for silica oxide nanofluid but still better resultsthan pure water. This shows that diamond and aluminium oxide nanofluids shows better thermal conductivity as it has lower total thermal resistance and thermal enhancement rate compared to other nanofluids. Diamond nanofluid also had higher heat capacity than aluminium oxide nanofluid as it had a lower vapour line temperature reading.
External shading geometry on buildings has been found to contribute substantially to reducing energy consumption for cooling. This study examines the effect of inclined wall self-shading strategy on heat gain in an office building. Field measurement of environmental variables such as ambient temperature, relative humidity, dew point, and wet bulb temperature was carried out in a case study inclined wall self-shading office building located in Putrajaya, Malaysia. The results of the validation of ApacheSim simulation software tool against the measured environmental variables indicated significant reliability having Pearson correlations ranging from 0.56 to 0.90. In establishing the relationship between different inclined wall strategies to the amount of heat gain, modification of the inclined wall self-shading projection (SSP) was modelled and experimented using ApacheSim simulation. Findings from the analysis revealed a relationship between heat gains into a building space and self-shading projection (SSP), as heat gains tend to reduce with increased SSP. From the findings, the optimum inclination angle of self-shading for effective heat gain reduction is based on a 45% self-shading projection. The application of inclined wall self-shading strategy in buildings would, therefore, bring about a reduction in heat gain, which invariably reduces energy consumption for cooling.
Kaolin, theoretically known as having low reactivity during geopolymerization, was used as a source of aluminosilicate materials in this study. Due to this concern, it is challenging to directly produce kaolin geopolymers without pre-treatment. The addition of ground granulated blast furnace slag (GGBS) accelerated the geopolymerization process. Kaolin-GGBS geopolymer ceramic was prepared at a low sintering temperature due to the reaction of the chemical composition during the initial stage of geopolymerization. The objective of this work was to study the influence of the chemical composition towards sintering temperature of sintered kaolin-GGBS geopolymer. Kaolin-GGBS geopolymer was prepared with a ratio of solid to liquid 2:1 and cured at 60 °C for 14 days. The cured geopolymer was sintered at different temperatures: 800, 900, 1000, and 1100 °C. Sintering at 900 °C resulted in the highest compressive strength due to the formation of densified microstructure, while higher sintering temperature led to the formation of interconnected pores. The difference in the X-ray absorption near edge structure (XANES) spectra was related to the phases obtained from the X-ray diffraction analysis, such as akermanite and anothite. Thermal analysis indicated the stability of sintered kaolin-GGBS geopolymer when exposed to 1100 °C, proving that kaolin can be directly used without heat treatment in geopolymers. The geopolymerization process facilitates the stability of cured samples when directly sintered, as well as plays a significant role as a self-fluxing agent to reduce the sintering temperature when producing sintered kaolin-GGBS geopolymers.
The problem of entropy generation analysis and natural convection in a nanofluid square cavity with a concentric solid insert and different temperature distributions is studied numerically by the finite difference method. An isothermal heater is placed on the bottom wall while isothermal cold sources are distributed along the top and side walls of the square cavity. The remainder of these walls are kept adiabatic. Water-based nanofluids with Al 2 O 3 nanoparticles are chosen for the investigation. The governing dimensionless parameters of this study are the nanoparticles volume fraction ( 0 ≤ ϕ ≤ 0.09 ), Rayleigh number ( 10 3 ≤ R a ≤ 10 6 ) , thermal conductivity ratio ( 0.44 ≤ K r ≤ 23.8 ) and length of the inner solid ( 0 ≤ D ≤ 0.7 ). Comparisons with previously experimental and numerical published works verify a very good agreement with the proposed numerical method. Numerical results are presented graphically in the form of streamlines, isotherms and local entropy generation as well as the local and average Nusselt numbers. The obtained results indicate that the thermal conductivity ratio and the inner solid size are excellent control parameters for an optimization of heat transfer and Bejan number within the fully heated and partially cooled square cavity.
The ever-increasing demand for the finite source of oil has led oil production companies to produce and transport the produced crude oil as efficiently and economically as possible. One of the major concerns especially in waters like the South China Sea is the deposition of wax on the walls of the pipeline or wellbore, constricting and hindering the hydrocarbon flow. This is due to the low seabed temperatures, which can be below the wax appearance temperature (WAT), leading to the deposition of wax out of waxy crude oil through the molecular dispersion mechanism. Currently, many prevention and remedy methods are in place to overcome the problem, but most of the additives possess environmental threat, as most of the chemical solutions used are toxic, nonorganic, and costly. Hence, this paper aims to provide some insights into the effect of palm oil derivatives such as crude palm oil (CPO) and crude palm kernel oil (CPKO) on wax inhibition. The effect of aging time (i.e., immersion time) was also evaluated. A comparison was made between paraffin inhibition efficiency results (PIE %) obtained by CPO, CPKO, poly(ethylene-co-vinyl acetate) (EVA), and triethanolamine (TEA). It was observed that the average efficiency of 81.67% was obtained when 1% CPO was added to heavy crude oil. The wax inhibition performance reached a plateau after 1.5 h of aging time for all of the investigated samples.
Exposure to hot and humid weather conditions will often lead to consuming a vast amount of electricity for cooling. Heating, ventilation, and air conditioning (HVAC) systems are customarily known as the largest consumers of energy in institutions and other facilities which raises the question regarding the impact of the weather conditions to the amount energy consumed. The academic building is a perfect example where a constant fixed daily operating characteristic is measured by the hour, aside from the occasional semester break. Therefore, it can be assumed that the daily HVAC services on an academic facility will operate on a fixed schedule each day, having a similar pattern all year round. This article aims to present an analysis on the relationship between typical weather data by implying the test reference year (TRY) and academic building electricity consumption in an academic building located at Durian Tunggal, Melaka. Typical weather data were generated in representing the weather data between 2010 and 2018 using the Finkelstein-Schafer statistic (F-S statistic) in addition to a data set of electricity consumption. Descriptive analysis and correlation matrix analysis were conducted using JASP software for two sets of sample data; Set A and Set B, with data points of 12 and 108, respectively. The result showed an alternate result with a positive correlation between 1)mean temperature-electricity consumption, and 2)mean rainfall-electricity consumption for data Set A, and a negative correlation between 1)mean temperature-electricity consumption and 2)mean rainfall-electricity consumption for data Set B.
Though fresh-cut products save our time, but they are very much prone to enzymatic browning that drastically affects product's quality and marketability. Drumstick pods are considered as super food due to high nutritional contents. However, the fresh-cut pods are prone to brown discoloration. The enzyme activities promote the softening and cut-surface browning of pods, thus deteriorates their texture, decreases consumer appeal and shortens the shelf life. So, we aimed to assess the effect of citric (1%) and ascorbic (1%) acid treatments on quality attributes of fresh-cut drumsticks at 3-d interval during storage (5 ± 1 °C). In general there was an increase in lignin and quinone contents, while phenolic content was decreased during storage. However, samples subjected to ascorbic acid dip had higher phenolic content, lower rate of lignin formation, and reduced membrane permeability. Enzyme activities (polyphenol oxidase and peroxidase) were found to increase during storage, however, samples treated with ascorbic acid showed lower activities than that of the control and citric acid treated samples. The reduced enzyme activities resulted in the reduced browning incidence and maintained the quality. Therefore, postharvest dip of fresh-cut drumstick in to ascorbic acid (1%) could be suggested to increase the shelf life with reduced browning during low temperature storage.
The life history and the influence of environmental parameters on Thalerosphyrus were investigated in two first-order rivers-the Batu Hampar River and the Teroi River of Gunung Jerai, Kedah-in northern peninsular Malaysia. Based on nymphal body length, Thalerosphyrus was found to be trivoltine in both rivers, regardless of the altitudinal difference, but its population abundance was four times higher in the Teroi River, presumably related to its better survival in the lower water temperature. At least nine instars of Thalerosphyrus were detected in the field-collected nymphs. Its life cycle was completed within 2.5-3.0 months, with overlapping cohorts and continual emergence of up to 3 months. The main driving factors of the high abundance of Thalerosphyrus were the water temperature and habitat quality.
Seeds of two selected clones of Artemisia annua L., TC1 and TC2, were germinated in a greenhouse. Four-week-old seedlings from both clones were grown in the Thù Ðúc province of Ho Chi Minh City on 2nd January 2009 and Ðà Lat on 20 th January 2009. During this study period in Thù Ðúc province, which is situated 4–5 m above sea level, was experiencing a tropical, dry season with temperatures ranging from 26.2°C–32.8°C. Ðà Lat, situated at 1500–2000 m above sea level, was having temperate, dry season with lower temperatures, ranging from 10.5°C–18.0°C. The high temperatures and low elevation in Thù Ðúc Province led to slow vegetative growth for all of the plants from the two different clones and the artemisinin contents were significantly reduced. The temperate environment of Ðà Lat supported robustly growing plants, with plant heights and branch lengths 4–5 times taller and longer that those planted at Thù Ðúc Province. The artemisinin contents of A. annua planted at Ðà Lat were 3–4 times greater than those cultivated at Thù Ðúc Province. Hence, this study indicated that the variations observed in plant growth and artemisinin contents were due to temperature effects because the two selected clones were genetically homogenous. The cold weather of Ðà Lat was suitable for planting of A. annua as opposed to the tropical weather of Thù Ðúc Province.
Objective: A case of caffeine-induced sleep disorder is reported to illustrate the clinical benefits of assessing culturally determined health beliefs in such presentations. Method: A middle-aged Malaysian Chinese male presented with caffeine-induced sleep disturbance arising from dietary modifications. Result: Assessing the contribution of cultural beliefs regarding hot and cold drinks led to successful management of the patient’s sleep disturbance. Conclusion: It is important for clinicians to explore health beliefs and associated dietary and lifestyle behaviours in caffeine-related sleep disorders.
Hydroxyapatite (HA) powder was synthesized via wet method using calcium nitrate hydrate (Ca(NO3)2.H2O) and diammonium hydrogen phosphate ((NH4)2HPO4) as raw materials. Powder obtained was milled using various milling speed ranging from 250 to 400 r.p.m. and sintered at 1300°C for 2hrs. Due to the nature of HA powder that decomposed at high temperature, XRD technique have been used in this work to determine the phase composition of the HA powder and also the crystallite size. The unmilled sample was used as the control group. Results show that sufficient heat supply generated from the milling process, initiates the decomposition of HA phase into ȕ-tricalcium phosphate (ȕ-TCP). Decomposition of HA starts to occur at the milling speed of 300 rpm, i.e the formation of ȕ-TCP was occurred at lower sintering temperature. It was believed that the decomposition of HA was associated with the formation of an intermediate phase, oxyapatite. Moreover, the crystallinity and particle size of the produced powder is very much affected by the milling speed and the stability of the HA. All milled powders possess spherical shape particle.
Ultrasound-assisted extraction (UAE) was applied for the extraction of bioactive valuable compounds from winter melon (Benincasa hispida) seeds. Effects of amplitude (25-75%), temperature (40-60°C) and sonication time (20-60 min) on crude extraction yield (CEY) and radical scavenging activities (RSA, % inhibition of DPPH˙ and ABTS˙+ free radicals) of extracts were determined using complete randomised design (CRD). The results showed that the CEY and RSA of extracts significantly affected by independent variables. The maximum value of CEY (97.14±0.36 mgg-1), scavenging of DPPH˙ radicals (32.12 ± 0.38%) and scavenging of ABTS˙+ radicals (40.52±0.73%) were obtained at the combined treatment conditions of 75%, 55°C and 40 min. The UAE results obtained were compared with those achieved by using conventional Soxhlet extraction (CSE) method. It was found UAE allowed extraction at lower temperature and the extracts obtained posses higher quality compare with CSE. UAE is a promising environment friendly technique for the extraction of bioactive compounds from winter melon (Benincasa hispida) seeds.