Octenyl succinic anhydride (OSA) modified sago starch was prepared in order to improve the emulsification properties of native starch. In the present study, the major factors affecting esterification were investigated with respect to OSA concentration, pH and reaction time using response surface methodology (RSM) based on central composite rotatable design (CCRD) to obtain the highest value of degree of substitution (DS). Results shown that the optimum conditions for OSA concentration, pH and reaction time were 5.00%, pH 7.20 and 9.65 h, respectively. At optimum condition, the esterification of sago starch with OSA resulted in DS value of 0.0120. The DS increased linearly with the increase in amount of OSA, whilst pH and reaction time show a curvature trend on the value of DS. The value of DS was found to be significantly affected by all the three variables. The experimental values under optimum condition were in good consistent with the predicted values (0.0131), which suggested that the optimisation by RSM is more efficient process than conventional optimisation.
The cell membrane is an important regulator for the cytotoxicity of chemotherapeutic agents. However, the biochemical and biophysical effects that occur in the membrane under the action of chemotherapy drugs are not fully described. In the present study, changes in the microviscosity of membranes of living HeLa-Kyoto tumor cells were studied during chemotherapy with paclitaxel, a widely used antimicrotubule agent. To visualize the microviscosity of the membranes, fluorescence lifetime imaging microscopy (FLIM) with a BODIPY 2 fluorescent molecular rotor was used. The lipid profile of the membranes was assessed using time-of-flight secondary ion mass spectrometry ToF-SIMS. A significant, steady-state decrease in the microviscosity of membranes, both in cell monolayers and in tumor spheroids, was revealed after the treatment. Mass spectrometry showed an increase in the unsaturated fatty acid content in treated cell membranes, which may explain, at least partially, their low microviscosity. These results indicate the involvement of membrane microviscosity in the response of tumor cells to paclitaxel treatment.
Density, viscosity and ionic conductivity data sets of deep eutectic solvents (DESs) formed by tetrabutylammonium bromide (TBABr) paired with ethlyene glycol, 1,3-propanediol, 1,5-pentanediol and glycerol hydrogen bond donors (HBDs) are reported. The properties of DES were measured at temperatures between 303 K and 333 K for HBD percentages of 66.7% to 90%. The effects of HBDs under different temperature and percentages are systematically analyzed. As expected, the measured density and viscosity of the studied DESs decreased with an increase in temperature, while ionic conductivity increases with temperature. In general, DESs made of TBABr and glycerol showed the highest density and viscosity and the lowest ionic conductivity when compared to other DESs. The presence of an extra hydroxyl group on glycerol in a DES affected the properties of the DES.
As a promising green and sustainable coating material, gum was extracted from durian seed to produce eutectogel, which the properties were tunable using natural deep eutectic solvent (NADES). Ten different eutectogels were successfully synthesized using durian seed gum (DSG) and xanthan gum (XG) gelators at different composition (5, 10, 15 %) to gel choline chloride-glucose (1:1), choline chloride-fructose (1:2) and betaine-glucose-water (1:1:1) NADESs. Results revealed that eutectogel was non-Newtonian and weak gel material with excellent thermostability up to 200 °C. When the gum content increased, the resulted eutectogel showed higher viscosity, yield stress, hardness, gumminess, adhesiveness, and weight holding capacity. In overall, choline chloride-fructose (1:2) NADES and 10 % of DSG formed an excellent eutectogel which remained stable and compatible upon 12 weeks of storage. It displayed superior viscoelastic, texture, gases and moisture barrier properties which were beneficial for food coating application. This eutectogel was able to extend the shelf life of fresh-cut apples during storage with lower weight loss and higher total phenolic content (TPC). The potential future of this well-characterized tunable DSG-derived eutectogel includes, but not limited to, food and pharmaceutical industries, smart sensing, flexible wearable electronics, water purification, supercapacitors and batteries.
This study investigates the effects of an arbitrary wall shear stress on unsteady magnetohydrodynamic (MHD) flow of a Newtonian fluid with conjugate effects of heat and mass transfer. The fluid is considered in a porous medium over a vertical plate with ramped temperature. The influence of thermal radiation in the energy equations is also considered. The coupled partial differential equations governing the flow are solved by using the Laplace transform technique. Exact solutions for velocity and temperature in case of both ramped and constant wall temperature as well as for concentration are obtained. It is found that velocity solutions are more general and can produce a huge number of exact solutions correlative to various fluid motions. Graphical results are provided for various embedded flow parameters and discussed in details.
This study examined whether pre-treating palm kernel expeller (PKE) with exogenous enzyme would degrade its fiber content; thus improving its metabolizable energy (ME), growth performance, villus height and digesta viscosity in broiler chickens fed diets containing PKE. Our results showed that enzyme treatment decreased (p<0.05) hemicellulose and cellulose contents of PKE by 26.26 and 32.62%, respectively; and improved true ME (TME) and its nitrogen corrected value (TMEn) by 38% and 33%, respectively, compared to the raw sample. Average daily gain (ADG), feed intake and feed conversion ratio (FCR) of chickens fed on different dietary treatments in the grower period were not significantly different. Although there was no difference in feed intake (p>0.05) among treatment groups in the finisher period, ADG of chickens in the control (PKE-free diet) was higher (p<0.05) than in all treatment groups fed either 20 or 30% PKE, irrespective of with or without enzyme treatment. However, ADG of birds fed with 20% PKE was higher than those fed with 30% PKE. The FCR of chickens in the control was the lowest (2.20) but not significantly different from those fed 20% PKE diets while birds in the 30% PKE diets recorded higher (p>0.05) FCR. The intestinal villus height and crypt depth (duodenum, jejunum and ileum) were not different (p>0.05) among treatments except for duodenal crypt depth. The villus height and crypt depth of birds in enzyme treated PKE diets were higher (p<0.05) than those in the raw PKE groups. Viscosity of the intestinal digesta was not different (p>0.05) among treatments. Results of this study suggest that exogenous enzyme is effective in hydrolyzing the fiber (hemicellulose and cellulose) component and improved the ME values of PKE, however, the above positive effects were not reflected in the growth performance in broiler chickens fed the enzyme treated PKE compared to those received raw PKE. The results suggest that PKE can be included up to 5% in the grower diet and 20% in the finisher diet without any significant negative effect on FCR in broiler chickens.
Lipase-catalyzed production of palm esters by alcoholysis of palm oil with oleyl alcohol in n-hexane was performed in 2L stirred-tank reactor (STR). Investigation on the performance of reactor operation was carried out in batch mode STR with single impeller mounted on the centrally located shaft. Rushton turbine (RT) impellers provide the highest reaction yield (95.8%) at lower agitation speed as compared to AL-hydrofoil (AL-H) and 2-bladed elephant ear (EE) impellers. Homogenous enzyme particles suspension was obtained at 250 rpm by using RT impeller. At higher impeller speed, the shear effect on the enzyme particles caused by agitation has decreased the reaction performance. Palm esters reaction mixture in STR follows Newtons' law due to the linear relation between the shear stress (tau) and shear rate (dupsilon/dy). High stability of Lipozyme RM IM was observed as shown by its ability to be repeatedly used to give high percentage yield (79%) of palm esters even after 15 cycles of reaction. The process was successfully scale-up to 75 L STR (50 L working volume) based on a constant impeller tip speed approach, which gave the yield of 97.2% after 5h reaction time.
Corn starches with different amylose-to-amylopectin ratio (waxy, normal, Hylon V, and Hylon VII) were treated with five doses of gamma irradiation (1, 5, 10, 25, and 50 kGy). The effects of gamma irradiation on the physicochemical properties of starch samples were investigated. Waxy samples showed an increase of amylose-like fractions when irradiated at 10 kGy. The reduction in apparent amylose content increased with amylose content when underwent irradiation at 25 and 50 kGy. Low amylose starches lost their pasting ability when irradiated at 25 and 50 kGy. Results from thermal behavior and pasting profile suggested that low level of cross-linking occurred in Hylon VII samples irradiated at 5 kGy. Severe reduction in pasting properties, gelatinization temperatures and relative crystallinity with increasing irradiation intensity revealed that waxy samples were affected more by gamma irradiation; this also indicated amylopectin was the starch fraction most affected by gamma irradiation. Alteration level was portrayed differently when different kind of physicochemical properties were investigated, in which the pasting properties and crystallinity of starches were more immensely influenced by gamma irradiation while thermal behavior was less affected. Despite the irradiation level, the morphology and crystal pattern of starch granules were found remain unchanged by irradiation.
used with bonded retainers. Setting: Department of Orthodontics, UCL Eastman Dental Institute, United Kingdom. Methods: Flowable composite resins (Transbond TM Supreme LV, StarFlowTM and Tetric EvoFlow®) and non -flowable control resin (TransbondTM LR) were made into cylinders prior to bonding to hydoxyapatite discs. They were then mounted into jigs and tested in the InstronTM Universal Testing Machine in both shear and tensile modes. Results: The highest mean shear bond strength was seen with StarFlow TM (14.09 MPa), which was significantly higher than both TransbondTM LR (9.48 MPa) and TransbondTM Supreme LV (8.20 MPa). The mean shear bond strength of Tetric EvoFlow® (11.86 MPa) was also significantly higher than TransbondTM Supreme LV. The highest mean tensile bond strength was seen with Tetric EvoFlow® (2.14 MPa), which was significantly higher than TransbondTM LR (1.15 MPa) and TransbondTM Supreme LV (0.61 MPa) but not significantly different to StarFlowTM (1.47 MPa). For shear loading, StarFlowTM had the highest 50th percentile survival estimate at 15.10 MPa, followed by Tetric EvoFlow® (13.00 MPa) and TransbondTM Supreme LV (7.50 MPa). TransbondTM LR had a 50th percentile estimate at 9.00 MPa. For tensile loading, Tetric EvoFlow® had the highest 50th percentile survival estimate at 2.50 MPa, followed by StarFlowTM (1.30 MPa) and TransbondTM Supreme LV (0.50 MPa). TransbondTM LR had a 50th percentile estimate at 1.00 MPa. Conclusions: Mean shear bond strengths for all of the resins were significantly higher than the mean tensile bond strengths. StarFlowTM and Tetric EvoFlow® could potentially be suitable clinical alternatives to TransbondTM LR due to its low viscosity flow characteristics and adequate shear and tensile bond strengths.
The three dimensional free convection boundary layer flow near a stagnation point region is embedded in viscous nanofluid with the effect of g-jitter is studied in this paper. Copper (Cu) and aluminium oxide (Al2O3) types of water base nanofluid are cho- sen with the constant Prandtl number, Pr=6.2. Based on Tiwari-Das nanofluid model, the boundary layer equation used is converted into a non-dimensional form by adopting non- dimensional variables and is solved numerically by engaging an implicit finite-difference scheme known as Keller-box method. Behaviors of fluid flow such as skin friction and Nusset number are studied by the controlled parameters including oscillation frequency, amplitude of gravity modulation and nanoparticles volume fraction. The reduced skin friction and Nusset number are presented graphically and discussed for different values of principal curvatures ratio at the nodal point. The numerical results shows that, in- crement occurs in the values of Nusset number with the presence of solid nanoparticles together with the values of the skin friction. It is worth mentioning that for the plane stagnation point there is an absence of reduced skin friction along the y-direction where as for axisymmetric stagnation point, the reduced skin friction for both directions are the same. As nanoparticles volume fraction increased, the skin friction increased as well as the Nusset number. The results, indicated that skin frictions of copper are found higher than aluminium oxide.
Physical properties of ripe banana flour were studied in Cavendish and Dream banana, in order to distinguish the two varieties. Flour was analyzed for pH, total soluble solids (TSS), water holding capacity
(WHC) and oil holding capacity (OHC) at 40, 60 and 80 °C, color values L*, a* and b*, back extrusion force
and viscosity. Physical properties data were analyzed by cluster analysis (CA) and discriminant analysis (DA). CA showed that the two types of flour were different in terms of selected physical properties. DA indicated that WHC at 60 °C was the main contributor in discriminating the two types of flour.
In this study, acid-thinned starch was blended with konjac glucomannan or psyllium husk powder at a concentration of 3% w/w (starch basis). The blends were characterized by pasting analysis and rheological
properties evaluation. Jelly candy was made from the blends and textural characteristics were studied. Pasting analysis showed that both gums were found to significantly increase some of the pasting parameters, such as peak viscosity, trough, breakdown, final viscosity and setback values. From the frequency sweep, it was found that addition of konjac glucomanan or psyllium husk powder increased the storage modulus (G’) and loss modulus (G’’) values, with psyllium added sample showing more prominent effect than konjac added ones, when compared to the control samples. All samples were found to demonstrate thixotropic flow behaviour. Jelly candy texture profile analysis revealed that konjac glucomannan or psyllium husk powder addition, although decreasing chewability, but rendered the jelly candy less sticky.
The aim of this study were to find out the physicochemical characteristics of cholesterol-reduced egg yolk powder and its application in the production of mayonnaises. Cholesterol-reduced egg yolk powder (CREYP) were prepared from removal of cholesterol by formation of cholesterol:β-cyclodextrin inclusion complex. The physicochemical characteristics of CREYP and NEYP were foaming capacity (FC): 1.96%, 4%; foaming stability (FS): 96.48%, 94.55%; emulsion capacity (EC): 59.82%, 58.43% and emulsion stability (ES): 43.94%, 41.48% respectively. Whereas the viscosity of CREY, NEY and commercial mayonnaises were 8000, 4768 and 6747 cP respectively. The lightness (L*), redness (a*), yellowness (b*), saturation (C*) and hue angle (h°) values for CREYP and NEYP results showed significantly different (p>0.05) for all chroma values with CREYP showed higher L* and h° values but lower in a*, b* and C* values showing that the yellow colour of NEYP lessened. Commercial mayonnaise appeared to be lighter and less yellowish than CREY mayonnaises with L* and b* values of
commercial to CREY mayonnaises were L*: 78.34; 63.78% and b*: 8.29; 14.98% respectively. It can be concluded that CREYP can be used as replace to the NEYP and whole liquid egg yolk
with enhance nutritional values. The results obtained from this study will be very useful for producing CREYP.
Unsteady mixed convection flow of Casson fluid towards a nonlinearly stretching sheet with the slip and convective boundary conditions is analyzed in this work. The effects of Soret Dufour, viscous dissipation and heat generation/absorption are also investigated. After using some suitable transformations, the unsteady nonlinear problem is solved by using Keller-box method. Numerical solutions for wall shear stress and high temperature transfer rate are calculated and compared with previously published work, an excellent arrangement is followed. It is noticed that fluid velocity reduces for both local unsteadiness and Casson parameters. It is likewise noticed that the influence of a Dufour number of dimensionless temperature is more prominent as compared to species concentration. Furthermore, the temperature was found to be increased in the case of nonlinear thermal radiation.
A study of kaolin addition in polypropylene (PP-kaolin) melt was carried out to characterize its flow behaviour and viscoelasticity at different temperatures. The compound of 20 wt% kaolin was prepared by melt mixing using two roll-mill heated at 185°C, while the compounded composites were put through a single screw extruder to evaluate its melt flow properties. The prepared PPKaolin composites exhibited a shear thinning behaviour and appeared to be strongly dependent on temperature. Moreover, it was also found that the power law index was constantly increased as the temperature increased. Meanwhile, a similar trend was observed for swelling ratio, whereby it also increased with increasing temperature. It was also observed that changes in the die temperatures would result in the formation of obvious bubble like surface morphology, and it became more prominent when the temperature was lowered.
The present project investigated the potential of utilizing corncobs and sugar cane waste as viscosivier in drilling fluid. For this purpose, the synthetic-based drilling fluid, Sarapar 147, was used as the base fluid. Both the materials were subjected to pre-treatment of drying, dehumidifying, grinding and sieving process prior to rheological tests. The rheological tests were conducted in accordance with the API 13B specifications to measure mud density, plastic viscosity, yield point, 10-second and 10-minute gel strength. The study found that plastic viscosity and yield point had a direct relationship with the amount of materials added. To drill fluid additive with corn cobs, the density, plastic viscosity and yield point were increased when the amount of additives were increased. Based on these experiments, both additives were found to have the potential to be used as additive in drilling fluid. In particular, they were able to improve its rheological properties by increasing the density, plastic viscosity and yield point. The suitable concentration for the corn cobs and sugar cane is 6.45 lb/bbl and 9.43 lb/bbl, respectively.
The rheological properties, microstructure, textural properties, colour and droplet size distribution of mayonnaise-like emulsion models prepared using 10-30wt.% of palm olein-based diacylglycerol (POL-DAG) oil were compared with those of the control (100wt.% VCO) model. There were significant (P<0.05) differences in the particle size distribution of the oil droplets, the textural properties, and the rheological properties of the various emulsion models. The rheological analysis included the determination of the flow curves, yield stress, thixotropy, apparent viscosity, and viscoelastic parameters. The concentrated oil-in-water (O/W) emulsion with 30wt.% POL-DAG substitution exhibited high thixotropy. The POL-DAG content had a substantial effect on the rheological properties of yield stress, storage modulus (G') and loss modulus (G″). The pseudoplastic behaviour of the emulsions was demonstrated. The size of the particles in the 30% POL-DAG-substituted emulsion was dramatically increased after one day and 30days of storage. All of the emulsion samples with POL-DAG substituted for VCO showed a relatively non-uniform bimodal droplet size distribution after one day of storage. In general, substitution of 10-20wt.% POL-DAG oil is appropriate for preparing O/W emulsions that had flow curves and textural properties similar to those of the control sample.
The present study was conducted to investigate the effect of oyster mushroom (Pleurotus sajorcaju,
PSC) addition to partially replace coconut milk powder on nutritional composition and
sensory values of Herbal Seasoning (HS). This study evaluates the nutritional composition,
dietary fibre and sensory acceptance of HS that processed using six different formulations
with different levels of PSC powder, namely 0% (A), 20% (B), 40% (C), 60% (D), 80% (E)
and 100% (F). The use of PSC powder substantially brought down the fat content of HS.
The fat content of PSC-based HS was ranged from 13.82±0.84% to 8.16±0.74%. The protein
content showed an increasing trend in line with increasing of PSC powder ranging from 7%
to 12%.Substitution of coconut milk powder with PSC powder resulted in significantly higher
(p0.05).The panels preferred HS formulated with PSC powder since its
enhance colour and viscosity attributes of the products. In brief, HS formulated with more than
40% PSC powder is recommended since it has significant nutrients and palatably accepted by
sensorial panellists.
This paper investigates the field-dependent rheological properties of magnetorheological (MR) fluid used to fill in MR dampers after long-term cyclic operation. For testing purposes, a meandering MR valve was customized to create a double-ended MR damper in which MR fluid flowed inside the valve due to the magnetic flux density. The test was conducted for 170,000 cycles using a fatigue dynamic testing machine which has 20 mm of stroke length and 0.4 Hz of frequency. Firstly, the damping force was investigated as the number of operating cycles increased. Secondly, the change in viscosity of the MR fluid was identified as in-use thickening (IUT). Finally, the morphological observation of MR particles was undertaken before and after the long-term operation. From these tests, it was demonstrated that the damping force increased as the number of operating cycles increases, both when the damper is turn on (on-state) and off (off-state). It is also observed that the particle size and shape changed due to the long operation, showing irregular particles.