Sensing and communication coverage are among the most important trade-offs in Wireless Sensor Network (WSN) design. A minimum bound of sensing coverage is vital in scheduling, target tracking and redeployment phases, as well as providing communication coverage. Some methods measure the coverage as a percentage value, but detailed information has been missing. Two scenarios with equal coverage percentage may not have the same Quality of Coverage (QoC). In this paper, we propose a new coverage measurement method using Delaunay Triangulation (DT). This can provide the value for all coverage measurement tools. Moreover, it categorizes sensors as 'fat', 'healthy' or 'thin' to show the dense, optimal and scattered areas. It can also yield the largest empty area of sensors in the field. Simulation results show that the proposed DT method can achieve accurate coverage information, and provides many tools to compare QoC between different scenarios.
Matched MeSH terms: Computer Communication Networks/instrumentation*
A wireless sensor network is a large collection of sensor nodes with limited power supply and constrained computational capability. Due to the restricted communication range and high density of sensor nodes, packet forwarding in sensor networks is usually performed through multi-hop data transmission. Therefore, routing in wireless sensor networks has been considered an important field of research over the past decade. Nowadays, multipath routing approach is widely used in wireless sensor networks to improve network performance through efficient utilization of available network resources. Accordingly, the main aim of this survey is to present the concept of the multipath routing approach and its fundamental challenges, as well as the basic motivations for utilizing this technique in wireless sensor networks. In addition, we present a comprehensive taxonomy on the existing multipath routing protocols, which are especially designed for wireless sensor networks. We highlight the primary motivation behind the development of each protocol category and explain the operation of different protocols in detail, with emphasis on their advantages and disadvantages. Furthermore, this paper compares and summarizes the state-of-the-art multipath routing techniques from the network application point of view. Finally, we identify open issues for further research in the development of multipath routing protocols for wireless sensor networks.
Matched MeSH terms: Computer Communication Networks/instrumentation*
Wireless Sensor Networks (WSNs) are vulnerable to clone attacks or node replication attacks as they are deployed in hostile and unattended environments where they are deprived of physical protection, lacking physical tamper-resistance of sensor nodes. As a result, an adversary can easily capture and compromise sensor nodes and after replicating them, he inserts arbitrary number of clones/replicas into the network. If these clones are not efficiently detected, an adversary can be further capable to mount a wide variety of internal attacks which can emasculate the various protocols and sensor applications. Several solutions have been proposed in the literature to address the crucial problem of clone detection, which are not satisfactory as they suffer from some serious drawbacks. In this paper we propose a novel distributed solution called Random Walk with Network Division (RWND) for the detection of node replication attack in static WSNs which is based on claimer-reporter-witness framework and combines a simple random walk with network division. RWND detects clone(s) by following a claimer-reporter-witness framework and a random walk is employed within each area for the selection of witness nodes. Splitting the network into levels and areas makes clone detection more efficient and the high security of witness nodes is ensured with moderate communication and memory overheads. Our simulation results show that RWND outperforms the existing witness node based strategies with moderate communication and memory overheads.
Matched MeSH terms: Computer Communication Networks/instrumentation*
Spectrum scarcity is a major challenge in wireless communications systems requiring efficient usage and utilization. Cognitive radio network (CRN) is found as a promising technique to solve this problem of spectrum scarcity. It allows licensed and unlicensed users to share the same licensed spectrum band. Interference resulting from cognitive radios (CRs) has undesirable effects on quality of service (QoS) of both licensed and unlicensed systems where it causes degradation in received signal-to-noise ratio (SIR) of users. Power control is one of the most important techniques that can be used to mitigate interference and guarantee QoS in both systems. In this paper, we develop a new approach of a distributed power control for CRN based on utility and pricing. QoS of CR user is presented as a utility function via pricing and a distributed power control as a non-cooperative game in which users maximize their net utility (utility-price). We define the price as a real function of transmit power to increase pricing charge of the farthest CR users. We prove that the power control game proposed in this study has Nash Equilibrium as well as it is unique. The obtained results show that the proposed power control algorithm based on a new utility function has a significant reduction in transmit power consumption and high improvement in speed of convergence.
Matched MeSH terms: Computer Communication Networks/instrumentation*
In heterogeneous wireless networks, wireless local area network (WLAN) is highly preferred by mobile terminals (MTs) owing to its high transmission bandwidth and low access cost. However, in high-speed environment, handover from a cellular network to a WLAN cell will lead to a high number of handover failures and unnecessary handovers due to the WLAN coverage limitation and will become worse at high speed. A new vertical handover method is proposed to minimize the probability of handover failure and unnecessary handover while maximizing the usage of WLAN in high-speed environment. The simulation results show that the proposed method kept the probability of handover failure and unnecessary handover below 0.5% and 1%, respectively. Compared with previous studies, the proposed method reduced the number of handover failures and unnecessary handovers up to 80.0% and 97.7%, respectively, while the MT is highly mobile. Using the proposed prediction method, the MT can benefit high bandwidth and low network access cost from the WLAN with minimum interruption regardless of speed.
Matched MeSH terms: Computer Communication Networks/instrumentation*
Interest in the cognitive radio sensor network (CRSN) paradigm has gradually grown among researchers. This concept seeks to fuse the benefits of dynamic spectrum access into the sensor network, making it a potential player in the next generation (NextGen) network, which is characterized by ubiquity. Notwithstanding its massive potential, little research activity has been dedicated to the network layer. By contrast, we find recent research trends focusing on the physical layer, the link layer and the transport layers. The fact that the cross-layer approach is imperative, due to the resource-constrained nature of CRSNs, can make the design of unique solutions non-trivial in this respect. This paper seeks to explore possible design opportunities with wireless sensor networks (WSNs), cognitive radio ad-hoc networks (CRAHNs) and cross-layer considerations for implementing viable CRSN routing solutions. Additionally, a detailed performance evaluation of WSN routing strategies in a cognitive radio environment is performed to expose research gaps. With this work, we intend to lay a foundation for developing CRSN routing solutions and to establish a basis for future work in this area.
Matched MeSH terms: Computer Communication Networks/instrumentation*
Wireless Sensor Networks (WSNs) are important and necessary platforms for the future as the concept "Internet of Things" has emerged lately. They are used for monitoring, tracking, or controlling of many applications in industry, health care, habitat, and military. However, the quality of data collected by sensor nodes is affected by anomalies that occur due to various reasons, such as node failures, reading errors, unusual events, and malicious attacks. Therefore, anomaly detection is a necessary process to ensure the quality of sensor data before it is utilized for making decisions. In this review, we present the challenges of anomaly detection in WSNs and state the requirements to design efficient and effective anomaly detection models. We then review the latest advancements of data anomaly detection research in WSNs and classify current detection approaches in five main classes based on the detection methods used to design these approaches. Varieties of the state-of-the-art models for each class are covered and their limitations are highlighted to provide ideas for potential future works. Furthermore, the reviewed approaches are compared and evaluated based on how well they meet the stated requirements. Finally, the general limitations of current approaches are mentioned and further research opportunities are suggested and discussed.
Matched MeSH terms: Computer Communication Networks/instrumentation*
An efficiently unlimited address space is provided by Internet Protocol version 6 (IPv6). It aims to accommodate thousands of hundreds of unique devices on a similar link. This can be achieved through the Duplicate Address Detection (DAD) process. It is considered one of the core IPv6 network's functions. It is implemented to make sure that IP addresses do not conflict with each other on the same link. However, IPv6 design's functions are exposed to security threats like the DAD process, which is vulnerable to Denial of Service (DoS) attack. Such a threat prevents the host from configuring its IP address by responding to each Neighbor Solicitation (NS) through fake Neighbor Advertisement (NA). Various mechanisms have been proposed to secure the IPv6 DAD procedure. The proposed mechanisms, however, suffer from complexity, high processing time, and the consumption of more resources. The experiments-based findings revealed that all the existing mechanisms had failed to secure the IPv6 DAD process. Therefore, DAD-match security technique is proposed in this study to efficiently secure the DAD process consuming less processing time. DAD-match is built based on SHA-3 to hide the exchange tentative IP among hosts throughout the process of DAD in an IPv6 link-local network. The obtained experimental results demonstrated that the DAD-match security technique achieved less processing time compared with the existing mechanisms as it can resist a range of different threats like collision and brute-force attacks. The findings concluded that the DAD-match technique effectively prevents the DoS attack during the DAD process. The DAD-match technique is implemented on a small area IPv6 network; hence, the author future work is to implement and test the DAD-match technique on a large area IPv6 network.
Matched MeSH terms: Computer Communication Networks/instrumentation*