Potentially toxic metals pollution in the Straits of Malacca warrants the development of rapid, simple and sensitive assays. Enzyme-based assays are excellent preliminary screening tools with near real-time potential. The heavy-metal assay based on the protease ficin was optimized for mercury detection using response surface methodology. The inhibitive assay is based on ficin action on the substrate casein and residual casein is determined using the Coomassie dye-binding assay. Toxic metals strongly inhibit this hydrolysis. A central composite design (CCD) was utilized to optimize the detection of toxic metals. The results show a marked improvement for the concentration causing 50% inhibition (IC50) for mercury, silver and copper. Compared to one-factor-at-a-time (OFAT) optimization, RSM gave an improvement of IC50 (mg/L) from 0.060 (95% CI, 0.030-0.080) to 0.017 (95% CI, 0.016-0.019), from 0.098 (95% CI, 0.077-0.127) to 0.028 (95% CI, 0.022-0.037) and from 0.040 (95% CI, 0.035-0.045) to 0.023 (95% CI, 0.020-0.027), for mercury, silver and copper, respectively. A near-real time monitoring of mercury concentration in the Straits of Malacca at one location in Port Klang was carried out over a 4 h interval for a total of 24 h and validated by instrumental analysis, with the result revealing an absence of mercury pollution in the sampling site.
Matched MeSH terms: Water Pollutants, Chemical/analysis
Dispersants are approved for use in many countries (UK, South Korea, Australia, Egypt, France, Greece, Indonesia, Italy, Japan, Malaysia, Norway, Singapore, Spain, Thailand, and several coastal African, South American, and Middle Eastern countries). Here, the protocols of the most advanced (France, Norway, UK, Spain, Greece, Italy, USA, and Australia) are compared for identifying possible harmonization of approval procedures. Pre-toxicity testing, recognized oil datasets, common thresholds, standardized protocols, zoning, and monitoring are some of the aspects that can be discussed between countries.
In this work, nano-bimetallic Co/Fe oxides with different stoichiometric Co/Fe ratios were prepared using a novel one-step solution combustion method. The nano-bimetallic Co/Fe oxides were used for sulfamethoxazole (SMX) degradation via peroxymonosulfate (PMS) activation. The stoichiometric efficiencies of the as-prepared nano-bimetallic catalysts were calculated and compared for the first time. The radical generation was identified by electron paramagnetic resonance (EPR) as well as chemical quenching experiments, in which different scavengers were used and compared. The catalytic PMS activation mechanism in the presence of catalyst was examined by Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). The results showed that besides SO4•- and •OH, •OOH was also detected in the PMS/CoFeO2.5 system. Meanwhile, in addition to the previously proposed radical oxidation pathway, the results showed that SMX degradation also involved a non-radical oxidation, which could be verified by the degradation experiment without catalyst as well as the detection of 1O2. In the PMS activation process, cobalt functioned as the active site on CoFeO2.5 while Fe oxide functioned as the adsorption site. The electron transfer mechanism was proposed based on the XPS and metal leaching results. Additionally, via the detection of transformation products, different SMX transformation pathways involving nitration, hydroxylation and hydrolysis in the PMS/CoFeO2.5 system were proposed.
Landfill leachate contain persistent organic pollutants (POPs), namely, bisphenol A (BPA) and 2,4-Di-tert-butylphenol, which exceed the permissible limits. Thus, such landfill leachate must be treated before it is released into natural water courses. This article reports on investigations about the removal efficiency of POPs such as BPA and 2,4-Di-tert-butylphenol from leachate using locust bean gum (LBG) in comparison with alum. The vital experimental variables (pH, coagulant dosage and stirring speed) were optimised by applying response surface methodology equipped with the Box-Behnken design to reduce the POPs from leachate. An empirical quadratic polynomial model could accurately model the surface response with R2 values of 0.928 and 0.954 to reduce BPA and 2,4-Di-tert-butylphenol, respectively. Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM) were performed on treated flocs for further understanding. FTIR analysis revealed that the bridging of pollutant particles could be due to the explicit adsorption and bridging via hydrogen bonding of a coagulation mechanism. SEM micrographs indicated that the flocs produced by LBG have a rough cloudy surface and numerous micro-pores compared with alum, which enabled the capture and removal of POPs from leachate. Results showed that the reduction efficiencies for BPA and 2,4-Di-tert-butylphenol at pH 7.5 were 76% and 84% at LBG dosage of 500 mg·L-1 and 400 mg·L-1, respectively. Coagulant dosage and pH variation have a significant effect on POPs reduction in leachate. Coagulation/flocculation using LBG could be applied for POPs reduction in leachate as a pre-treatment prior to advanced treatments.
Sustainable wastewater treatment necessitates the application of natural and green material in the approach. Thus, selecting a natural coagulant in leachate treatment is a crucial step in landfill operation to prevent secondary environmental pollution due to residual inorganic coagulant in treated effluent. Current study investigated the application of guar gum in landfill leachate treatment. Central composite design in response surface methodology was used to optimize the performance of Chemical Oxygen Demand (COD) removal. Quadratic model developed indicated the optimum COD removal 22.57% at guar gum dosage of 44.39 mg/L, pH 8.56 (natural pH of leachate) and mixing speed 79.27 rpm. Scanning electron microscopy showed that floc was compact and energy-dispersive-x-ray analysis showed that guar gum was capable to adsorb multiple ions from the leachate. Structural characterization using Fourier Transform Infrared analysis demonstrated that hydrogen bonding between guar and pollutant particles was involved in coagulation and flocculation process. Therefore, guar gum coagulant present potential to be an alternative in leachate treatment where pH requirement is not required during treatment. Simultaneously, adsorption by guar gum offers added pollutant removal advantage.
This paper presents the landscape of research on airborne microplastics and nanoplastics (MPs/NPs) according to the bibliometric analysis of 147 documents issued between 2015 and 2021, extracted from the Web of Science database. The publications on airborne MPs/NPs have increased rapidly from 2015 onwards, which is largely due to the existence of funding support. Science of the Total Environment is one of the prominent journals in publishing related papers. China, England, the USA, and European Countries have produced a significant output of airborne MP/NP research works, which is associated with the availability of funding agencies regionally or nationally. The research hotspot on the topic ranges from the transport of airborne MPs/NPs to their deposition in the terrestrial or aquatic environments, along with the contamination of samples by indoor MPs/NPs. Most of the publications are either research or review papers related to MPs/NPs. It is crucial to share the understanding of global plastic pollution and its unfavorable effects on humankind by promoting awareness of the existence and impact of MPs/NPs. Funding agencies are vital in boosting the research development of airborne MPs/NPs. Some countries that are lacking funding support were able to publish research findings related to the field of interest, however, with lesser research output. Without sufficient fundings, some impactful publications may not be able to carry a substantial impact in sharing the findings and discoveries with the mass public.
Landfill leachate, which is a complicated organic sewage water, presents substantial dangers to human health and the environment if not properly handled. Electrochemical technology has arisen as a promising strategy for effectively mitigating contaminants in landfill leachate. In this comprehensive review, we explore various theoretical and practical aspects of methods for treating landfill leachate. This exploration includes examining their performance, mechanisms, applications, associated challenges, existing issues, and potential strategies for enhancement, particularly in terms of cost-effectiveness. In addition, this critique provides a comparative investigation between these treatment approaches and the utilization of diverse kinds of microbial fuel cells (MFCs) in terms of their effectiveness in treating landfill leachate and generating power. The examination of these technologies also extends to their use in diverse global contexts, providing insights into operational parameters and regional variations. This extensive assessment serves the primary goal of assisting researchers in understanding the optimal methods for treating landfill leachate and comparing them to different types of MFCs. It offers a valuable resource for the large-scale design and implementation of processes that ensure both the safe treatment of landfill leachate and the generation of electricity. The review not only provides an overview of the current state of landfill leachate treatment but also identifies key challenges and sets the stage for future research directions, ultimately contributing to more sustainable and effective solutions in the management of this critical environmental issue.
The objective of this research is to create a highly effective approach for eliminating pollutants from the environment through the process of photocatalytic degradation. The study centers around the production of composites consisting of CaCu3Ti4O12 (CCTO) and reduced graphene oxide (rGO) using an ultrasonic-assisted method, with a focus on their capacity to degrade ibuprofen (IBF) and ciprofloxacin (CIP) via photodegradation. The impact of rGO on the structure, morphology, and optical properties of CCTO was inspected using XRD, FTIR, Raman, FESEM, XPS, BET, and UV-Vis. Morphology characterization showed that rGO particles were dispersed within the CCTO matrix without any specific chemical interaction between CCTO and C in the rGO. The BET analysis revealed that with increasing the amount of rGO in the composite, the specific surface area significantly increased compared to the CCTO standalone. Besides, increasing rGO resulted in a reduction in the optical bandgap energy to around 2.09 eV, makes it highly promising photocatalyst for environmental applications. The photodegradation of IBF and CIP was monitored using visible light irradiation. The results revealed that both components were degraded above 97% after 60 min. The photocatalyst showed an excellent reusability performance with a slight decrease after five runs to 93% photodegradation efficiency.
Matched MeSH terms: Water Pollutants, Chemical/chemistry
Mountain salts produced from the highland region in NE Sarawak have a market value and also provide basic income to the communities. During the salt-making process, microplastics (MPs) may enter into commercial table salts from various sources, which has not been explored yet. Hence, the current research investigates the presence of MPs in the rock salts produced from the highland saline water in two different locations (L1 and L2) in NE Sarawak. Among the brine water and rock salt samples analysed, the highest concentrations of MPs were detected from the salt samples. It has been revealed that both the water and salt samples have the highest concentration of MPs occurring within the size range of 1-1000 μm. Transparent MPs are the most common colour observed in both salt and water samples, followed by white, blue, red, and black. The most prevalent shapes of MPs are fibers, which account for almost 47% in water samples and 87% in salt samples. Based on the ATR-FTIR study, polyethylene (PE) is the most prevalent polymer observed in salt samples, followed by polypropylene (PP), polystyrene (PS), and polyethylene terephthalate (PET). In water samples, PP is the most dominating polymer, followed by PE and PS. Through SEM microphotographs, fiber-type MPs have smooth surfaces, fragment-type MPs have rough edges, and sheet-type MPs have layered surfaces. EDX analysis revealed that carbon (C) and oxygen (O) are the most abundant elements, followed by aluminium (Al) and sodium (Na) in MPs. Based on the results, it is inferred that the MPs in the rock salts are mainly sourced from the different stages of salt-making production. This preliminary study shed light on the presence and characteristics of MPs in rock salts in this region. The research outcomes could support sustainable management plans to improve the salt quality and enhance the market value.
Matched MeSH terms: Water Pollutants, Chemical/analysis
Landfills are a source of groundwater pollution in Gaza Strip. This study focused on Deir Al Balah landfill, which is a unique sanitary landfill site in Gaza Strip (i.e., it has a lining system and a leachate recirculation system). The objective of this article is to assess the generated leachate quantity and percolation to the groundwater aquifer at a specific site, using the approaches of (i) the hydrologic evaluation of landfill performance model (HELP) and (ii) the water balance method (WBM). The results show that when using the HELP model, the average volume of leachate discharged from Deir Al Balah landfill during the period 1997 to 2007 was around, 6800 m3/year. Meanwhile, the average volume of leachate percolated through the clay layer was 550 m3/year, which represents around 8% of the generated leachate. Meanwhile, the WBM indicated that the average volume of leachate discharged from Deir Al Balah landfill during the same period was around 7660 m3/year--about half of which comes from the moisture content of the waste, while the remainder comes from the infiltration of precipitation and re-circulated leachate. Therefore, the estimated quantity of leachate to groundwater by these two methods was very close. However, compared with the measured leachate quantity, these results were overestimated and indicated a dangerous threat to the groundwater aquifer, as there was no separation between municipal, hazardous and industrial wastes, in the area.
Matched MeSH terms: Water Pollutants/analysis*; Water Pollutants, Chemical/analysis; Water Pollutants, Chemical/chemistry*
In pursuit of advancing photocatalysts for superior performance in water treatment and clean energy generation, researchers are increasingly focusing on layered double hydroxides (LDHs) which have garnered significant attention due to their customizable properties, morphologies, distinctive 2D layered structure and flexible options for modifying anions and cations. No review has previously delved specifically into ZnCr and NiCr LDH-based photocatalysts and therefore, this review highlights the recent surge in ZnCr and NiCr-based LDHs as potential photocatalysts for their applications in water purification and renewable energy generation. The structural and fundamental characteristics of layered double hydroxides and especially ZnCr-LDHs and NiCr-LDHs are outlined. Further, the various synthesis techniques for the preparation of ZnCr-LDHs, NiCr-LDHs and their composite and heterostructure materials have been briefly discussed. The applicability of ZnCr-LDH and NiCr-LDH based photocatalysts in tackling significant issues in water treatment and sustainable energy generation is the main emphasis of this review. It focuses on photocatalytic degradation of organic pollutants in wastewater, elucidating the principles and advancements for enhancing the efficiency of these materials. It also explores their role in H2 production through water splitting, conversion of CO2 into valuable fuels and NH3 synthesis from N2, shedding light on their potential for clean energy solutions. The insights presented herein offer valuable guidance for researchers working towards sustainable solutions for environmental remediation and renewable energy generation.
Matched MeSH terms: Water Pollutants, Chemical/analysis; Water Pollutants, Chemical/chemistry
Clostridium sp. strain Ade.TY is potentially a new biohydrogen-producing species isolated from landfill leachate sludge. Here we present the assembly and annotation of its genome, which may provide further insights into its gene interactions for efficient biohydrogen production.
The validity of using rainfall characteristics as lumped parameters for investigating the pollutant wash-off process such as first flush occurrence is questionable. This research study introduces an innovative concept of using sector parameters to investigate the relationship between the pollutant wash-off process and different sectors of the runoff hydrograph and rainfall hyetograph. The research outcomes indicated that rainfall depth and rainfall intensity are two key rainfall characteristics which influence the wash-off process compared to the antecedent dry period. Additionally, the rainfall pattern also plays a critical role in the wash-off process and is independent of the catchment characteristics. The knowledge created through this research study provides the ability to select appropriate rainfall events for stormwater quality treatment design based on the required treatment outcomes such as the need to target different sectors of the runoff hydrograph or pollutant species. The study outcomes can also contribute to enhancing stormwater quality modelling and prediction in view of the fact that conventional approaches to stormwater quality estimation is primarily based on rainfall intensity rather than considering other rainfall parameters or solely based on stochastic approaches irrespective of the characteristics of the rainfall event.
Leachate collected from the collection ponds of four landfill sites was investigated and compared for total coliforms and E. coli concentration as representatives of fecal pollution. Concentration of total coliforms and E. coli was comparable for leachate obtained from Kulim Landfill Site (KLS) and Ampang Landfill Site (ALS) with little variations. However, the level of indicator bacteria was significantly lower for Kuala Sepetang Landfill Site (KSLS), whereas Pulau Burung Landfill Site (PBLS) had the lowest concentration for both total coliforms and E. coli. Considering the landfills are currently operational, with the exception of ALS, the presence of indicator bacteria implies their inactivation prior to discharge. High concentration of indicator bacteria in ALS is attributed to the run-off entering the leachate pond. Greater concentration of ammonia and salinity level were partly responsible for lower concentration of indicator bacteria in leachate from KSLS and PBLS, indicating that salinty and ammonia could significantly affect the survival of indicator bacteria.
The widespread distribution of persistent organic pollutants (POPs) in landfill leachate is problematic due to their acute toxicity, carcinogenicity and genotoxicity effects, which could be detrimental to public health and ecological systems. The objective of this study was to evaluate the effective removal of POPs - namely, p-tert-Butylphenol and Pyridine, 3-(1-methyl-2-pyrrolidinyl)-, (S)- - from landfill leachate using locust bean gum (LBG), and in comparison with commonly used alum. The response surface methodology coupled with a Box-Behnken design was employed to optimize the operating factors for optimal POPs removal. A quadratic polynomial model was fitted into the data with the R2 values of 0.97 and 0.96 for the removal of p-tert-Butylphenol and Pyridine, 3-(1-methyl-2-pyrrolidinyl), (S)-, respectively. The physicochemical characteristics of the flocs produced by LBG and alum were evaluated with Fourier Transform Infrared (FTIR) spectroscopy and Scanning Electron Microscopy (SEM). The infrared spectra of LBG-treated floc were identical with LBG powder, but there was some variation in the peaks of the functional groups, signifying the chemical interactions between flocculants and pollutant particles resulting from POPs removal. The results showed that p-tert-Butylphenol and Pyridine, 3-(1-methyl-2-pyrrolidinyl)-, (S)- obtained 96% and 100% removal using 500 mg/L of LBG at pH 4. pH have a significant effect on POPs removal in leachate. It is estimated that treating one million gallons of leachate using alum (at 1 g/L dosage) would cost US$39, and using LBG (at 500 mg/L dosage) would cost US$2. LBG is eco-friendly, biodegradable and non-toxic and, hence, strongly recommended as an alternative to inorganic coagulants for the treatment of POPs in landfill leachate.
The widespread occurrence of microplastic has invaded the environment to an extent that it appears to be present throughout the globe. This review investigated the global abundance and distribution of microplastics in marine and freshwater ecosystems. Furthermore, the issues and challenges have been addressed for better findings in microplastics studies. Findings revealed that the accumulation of microplastics varies geographically, with locations, hydrodynamic conditions, environmental pressure, and time. From this review, it is crucial that proper regulations are proposed and implemented in order to reduce the occurrence of microplastics in the aquatic environment. Without appropriate law and regulations, microplastic pollution will eventually threaten human livelihood.
In an effort to determine the reason behind excellent nitrate remediation capacity at Kelantan region, a multivariate approach is employed to evaluate extent to which the influence of sea on soil geochemical composition affect variation pattern of groundwater quality. The results obtained from geochemical analysis of paleo-beach soil in coastal site at Bachok revealed multiple redox activity at different soil strata, involving both heterotrophic and autotrophic denitrification. In soil and water analysis, eight of the fourteen hydro-geochemical parameters (conductivity, temperature, soil texture, oxidation reduction potential, pH, total organic carbon, Fe, Cu, Mn, Cl-, SO42-, NO2-, NO3- and PO43-) measured using standard procedures were subjected to multivariate analysis. Evaluation of general variation pattern across the area reveals that the principal component analysis (PCA), hierarchical cluster analysis (HCA) and linear discriminant analysis (LDA) are in consonance with one another on apportioning three parameters (SO42-, Cl- and conductivity) to the coastal sites and two parameters (Fe and NH4+ or NO3-) to inland sites. The step forward analysis of LDA reveals four parameters in order of decreasing significance as Cl-, Fe and SO42-, while the two-way HCA identifies three clusters on location basis, respectively. In addition to the significant data reduction obtained, the results indicate that proximity to sea and location/geological-based influence are more significant than temporal-based influence in denitrification. By extension, the research reveals that influence of labile portion of natural resources is explorable for broader application in other remediation strategies.
Lead (Pb) is one of the toxic heavy metals that pollute the environment as a result of industrial activities. This study aims to optimize Pb removal from water by using horizontal free surface flow constructed wetland (HFSFCW) planted with Scirpus grossus. Optimization was conducted using response surface methodology (RSM) under Box-Behnken design with the operational parameters of initial Pb concentration, retention time, and aeration. Optimization results showed that 37 mg/L of initial Pb concentration, 32 days of retention time, and no aeration were the optimum conditions for Pb removal by using the systems. Validation test was run under two different conditions, namely, non-bioaugmented and bioaugmented with rhizobacteria (Bacillus cereus, B. pumilus, B. subtilis, Brevibacillus choshinensis, and Rhodococcus rhodochrous). Results of the validation test showed that Pb removal in water achieved 99.99% efficiency with 0.2% error from the RSM prediction, while the adsorption of Pb by plants reached 5160.18 mg/kg with 10.6% error from the RSM prediction. The bioaugmentation of the five rhizobacterial species showed a slight improvement in Pb removal from water and Pb adsorption by plants. However, no significant improvement was achieved (p water.
Landfills are one of the main point sources of groundwater pollution. This research mainly aims to assess the risk of nitrate [Formula: see text] transport from the unlined landfill to subsurface layers and groundwater using experimental results and the SESOIL model. Samples from 12 groundwater wells downstream of the landfill were collected and analyzed in 2008, 21 years after the landfill construction. The average [Formula: see text] concentration in the wells was 54 mg/L, slightly higher than the World Health Organization ([Formula: see text] 50 mg/L) standards. SESOIL model was used to predict the [Formula: see text] concentration at the bottom of the unsaturated zone. Results indicated that the current mean [Formula: see text] concentration at the bottom of the unsaturated zone is 75 mg/L. the model predicted that the level of NO3 will increased up to 325 mg/L within 30 years. Accordingly, the [Formula: see text] concentration in groundwater wells near the landfill area is expected to gradually increase with time. Although the current risk associated with the [Formula: see text] level might not be harm to adults, however, it might pose severe risks to both adults and infants in the near future due to [Formula: see text] leaching. Urgent mitigation measures such as final cell cover (cap), lining system and vertical expansion should be considered at the landfill to protect the public health in the area.