Kinetic studies of the enzymatic hydrolysis of molasses were conducted using glucoamylase. Central Sugar Refinery SDN BHD contains 13-20% glucose. The molasses was diluted and the kinetic experiments were conducted at 67 degrees C with 100-1000 mg/l of glucoamylase. The glucose contents of the molasses were enhanced after hydrolysis of molasses solution with 1000 mg/l glucoamylase. A Lineweaver-Burk plot was obtained based on enzyme kinetic data. The rate constant, Km and maximum reaction rate, Vmax for 500 mg/l of glucoamylase were 100 mmol/l (18 g/l) and 5 mmol/l min (0.9 g/l min), respectively. The maximum reaction rate, Vmax for 1000 mg/l of glucoamylase was doubled, to 100 mmol/l (18 g/l) and the rate constant, Km was the same for 500 mg/l of glucoamylase. The substrate inhibition model was noncompetitive based on the resulting Lineweaver-Burk plot for enzyme concentration of 500 and 1000 mg/l.
The intrinsic growth, substrate uptake, and product formation biokinetic parameters were obtained for the anaerobic bacterium, Clostridium ljungdahlii, grown on synthesis gas in various pressurized batch bioreactors. A dual-substrate growth kinetic model using Luong for CO and Monod for H2 was used to describe the growth kinetics of the bacterium on these substrates. The maximum specific growth rate (μ(max) = 0.195 h(-1)) and Monod constants for CO (K s,CO = 0.855 atm) and H2 (K(s,H2) = 0.412 atm) were obtained. This model also accommodated the CO inhibitory effects on cell growth at high CO partial pressures, where no growth was apparent at high dissolved CO tensions (P(CO)(∗) > 0.743 atm). The Volterra model, Andrews, and modified Gompertz were, respectively, adopted to describe the cell growth, substrate uptake rate, and product formation. The maximum specific CO uptake rate (q(max) = 34.364 mmol/g cell/h), CO inhibition constant (K(I) = 0.601 atm), and maximum rate of ethanol (R(max) = 0.172 mmol/L/h at P(CO) = 0.598 atm) and acetate (R(max) = 0.096 mmol/L/h at P(CO) = 0.539 atm) production were determined from the applied models.
In this study, the interactive effects of feed flow rate (QF) and up-flow velocity (V up) on the performance of an up-flow anaerobic sludge fixed film (UASFF) reactor treating palm oil mill effluent (POME) were investigated. Long-term performance of the UASFF reactor was first examined with raw POME at a hydraulic loading rate (HRT) of 3 d and an influent COD concentration of 44300 mg/l. Extreme reactor instability was observed after 25 d. Raw POME was then chemically pretreated and used as feed. Anaerobic digestion of pretreated POME was modeled and analyzed with two operating variables, i.e. feed flow rate and up-flow velocity. Experiments were conducted based on a central composite face-centered design (CCFD) and analyzed using response surface methodology (RSM). The region of exploration for digestion of the pretreated POME was taken as the area enclosed by the feed flow rate (1.01, 7.63 l/d) and up-flow velocity (0.2, 3 m/h) boundaries. Twelve dependent parameters were either directly measured or calculated as response. These parameters were total COD (TCOD) removal, soluble COD (SCOD) removal, effluent pH, effluent total volatile fatty acid (TVFA), effluent bicarbonate alkalinity (BA), effluent total suspended solids (TSS), CH4 percentage in biogas, methane yield (Y M), specific methanogenic activity (SMA), food-to-sludge ratio (F/M), sludge height in the UASB portion and solid retention time (SRT). The optimum conditions for POME treatment were found to be 2.45 l/d and 0.75 m/h for QF and V up, respectively (corresponding to HRT of 1.5 d and recycle ratio of 23.4:1). The present study provides valuable information about interrelations of quality and process parameters at different values of the operating variables.