The integration of hydrogen in the primary energy mix requires a major technological shift in virtually every energy-related application. This study has attempted to investigate the techno-economic solar photovoltaic (PV) integrated water electrolysis and waste incineration system. Three different strategies, i.e., (i) PV + Battery(Hybrid mode with required batteries); (ii) auto-ignition (Direct coupling); and (iii) PV + Secondary-Electrolyzer(Direct coupling assisted with secondary electrolyzer), have been envisioned. The 'PV + Battery' consume 42.42 % and 15.07 % less energy than the auto-ignition and 'PV + Secondary-Electrolyzer' methods. However, the capital cost of 'PV + Battery' has been calculated to be 15.4 % and 11.8 % more than auto-ignition and 'PV + Secondary-Electrolyzer, respectively.The energy consumption relative to waste input, the 'PV + Battery' method used 80 % less energy, while auto-ignition and 'PV + Secondary-Electrolyzer' showed 70.5 % and 77.5 % less energy, respectively. Furthermore, these approaches showed a vast difference in cost-benefit for the longer run. 'PV + Battery' was forecasted to be 73.3 % and 23.3 % more expensive than auto-ignition and 'PV + Secondary-Electrolyzer' methods, respectively, for 30 years. Overall, this study can benefit from using either of these methods depending on the application, usage scale, and climatic conditions.
Stabilizing/solidificating municipal solid waste incineration fly ash (MIFA) with cement is a common strategy, and it is critical to study the high-value utilization of MIFA in ordinary Portland cement (OPC) components. With this aim, binary-binding-system mortar was produced by partially replacing OPC (∼50%) with MIFA, and the effects of different curing regimes (steam curing and carbonation curing) on the properties of the cement mortar were studied. The results showed that the setting time of the cement paste was shorten with the increase of MIFA content, and steam curing accelerated the hardening of the mixture. Although the incorporation of MIFA reduced the strength of the mortar, compared to conventional curing method, steam curing and carbonation curing increased the 3-d strength of the mortar. For high-volume MIFA mortars, the CO2-cured samples had the highest long-term strength and lowest permeability. The incorporation of MIFA increased the initial porosity of the mortar, thereby significantly increasing the carbonation degree and crystallinity of the reaction product - CaCO3. Steam curing also further narrowed the difference in the hydration degree between MIFA-modified sample and plain paste, which may be due to the enhanced hydraulic reactivity of MIFA at high temperatures. Although the incorporation of MIFA increased the porosity of the mortar, this waste-derived SCM refined the bulk pore structure and decreased the interconnected porosity. Additionally, the heavy metal leaching contents of MIFA-modified mortars were all below 1%, which meet the requirements of Chinese standards. Compared with standard curing, steam curing and carbonation curing made the early-age and long-term performance of MIFA-modified mortar better, which can promote the efficient application of MIFA in OPC products.
COVID-19 has led to the enormous rise of medical wastes throughout the world, and these have mainly been generated from hospitals, clinics, and other healthcare establishments. This creates an additional challenge in medical waste management, particularly in developing countries. Improper managing of medical waste may have serious public health issues and a significant impact on the environment. There are currently three disinfection technologies, namely incineration, chemical and physical processes, that are available to treat COVID-19 medical waste (CMW). This study focuses on thermochemical process, particularly pyrolysis process to treat the medical waste. Pyrolysis is a process that utilizes the thermal instability of organic components in medical waste to convert them into valuable products. Besides, the technique is environmentally friendly, more efficient and cost-effective, requires less landfill capacity, and causes lower pollution. The current pandemic situation generates a large amount of plastic medical wastes, which mainly consists of polyethylene, polypropylene, polystyrene, polyethylene terephthalate, and nylon. These plastic wastes can be converted into valuable energy products like oil, gas and char through pyrolysis process. This review provides detailed information about CMW handling, treatment, valuable product generation, and proper discharge into the open environment.
Industrial plastic waste is growing globally at an alarming rate and environmental pollution from traditional landfill disposal and incineration treatments are of great concern. As a strategy to reduce plastic pollution, value-added composite materials from industrial plastic wastes reinforced with recycled nylon fibers for use in floor paving tile applications were developed. This is to address the disadvantages of existing ceramic tiles which are relatively heavy, brittle, and expensive. The plastic waste composite structures were produced via compression molding technique at an optimized randomly oriented constant fiber volume fraction of 50 wt% after the initial sorting, cleaning, drying, pulverizing, and melt-mixing. The molding temperature, pressure, and time for the composite's structures were 220 ℃, 65 kg.cm-3, and 5 min respectively. The composites' thermal, mechanical, and microstructural properties were characterized in accordance with appropriate ASTM standards. From the results obtained, the differential scanning calorimetry (DSC) of mixed plastic wastes and nylon fiber wastes showed a processing temperature range of 130-180 ℃, and 250 ℃ respectively. Thermal degradation temperature (TGA) of the plastic and nylon fiber waste composites were stable above 400 ℃ with maximum bending strength, however, the reinforced plastic waste sandwiched composite structures had outstanding mechanical properties indicating unique characteristics suitable for floor paving tiles. Hence, the current research has developed tough and lightweight tiles composites that are economically viable, and their application will contribute to the development of the building and construction sectors thereby reducing about 10-15% of annual plastic waste generation and a sustainable environment.
An appropriate technology for waste utilisation, especially for a large amount of abundant pressed-shredded oil palm empty fruit bunch (OFEFB), is important for the oil palm industry. Self-sustained pyrolysis, whereby oil palm biomass was combusted by itself to provide the heat for pyrolysis without an electrical heater, is more preferable owing to its simplicity, ease of operation and low energy requirement. In this study, biochar production under self-sustained pyrolysis of oil palm biomass in the form of oil palm empty fruit bunch was tested in a 3-t large-scale pool-type reactor. During the pyrolysis process, the biomass was loaded layer by layer when the smoke appeared on the top, to minimise the entrance of oxygen. This method had significantly increased the yield of biochar. In our previous report, we have tested on a 30-kg pilot-scale capacity under self-sustained pyrolysis and found that the higher heating value (HHV) obtained was 22.6-24.7 MJ kg(-1) with a 23.5%-25.0% yield. In this scaled-up study, a 3-t large-scale procedure produced HHV of 22.0-24.3 MJ kg(-1) with a 30%-34% yield based on a wet-weight basis. The maximum self-sustained pyrolysis temperature for the large-scale procedure can reach between 600 °C and 700 °C. We concluded that large-scale biochar production under self-sustained pyrolysis was successfully conducted owing to the comparable biochar produced, compared with medium-scale and other studies with an electrical heating element, making it an appropriate technology for waste utilisation, particularly for the oil palm industry.
Selective Non-Catalytic Reduction (SNCR) of nitric oxide has been studied experimentally by injecting aqueous urea solution with and without additive in a pilot-scale diesel fired tunnel furnace at 3.4% excess oxygen level and with low ppm of baseline NO(x) ranging from 65 to 75 ppm within the investigated temperature range. The tests have been carried out using commercial grade urea as NO(x) reducing agent and commercial grade sodium carbonate as additive. The furnace simulated the small-scale combustion systems, where the operating temperatures are usually in the range of about 973 to 1323 K and NO(x) emission level remains below 100 ppm. With 5% plain urea solution, at Normalized Stoichiometric Ratio (NSR) of 4 as much as 54% reduction was achieved at 1128 K, whilst in the additive case the NO(x) reduction was improved to as much as 69% at 1093 K. Apart from this improvement, in the additive case, the effective temperature window as well as peak temperature of NO(x) reduction shifted towards lower temperatures. The result is quite significant, especially for this investigated level of baseline NO(x). The ammonia slip measurements showed that in both cases the slip was below 16 ppm at NSR of 4 and optimum temperature of NO(x) reduction. Finally, the investigations demonstrated that urea based SNCR is quite applicable to small-scale combustion applications and commercial grade sodium carbonate is a potential additive.
A choice experiment analysis was conducted to estimate the preference for specific waste disposal technologies in Malaysia. The study found that there were no significant differences between the choice of a sanitary landfill or an incinerator. What matters is whether any disposal technology would lead to obvious social benefits. A waste disposal plan which is well linked or integrated with the community will ensure its acceptance. Local authorities will be challenged to identify solid waste disposal sites that are technically appropriate and also socially desirable.
Power generation from biomass is an attractive technology that utilizes agricultural residual waste. In order to explain the behavior of biomass-fired fluidized bed incinerator, biomass sources from agricultural residues (rice husk and palm kernel) were co-fired with coal in a 0.15m diameter and 2.3m high fluidized bed combustor. The combustion efficiency and carbon monoxide emissions were studied and compared with those for pure coal combustion. Co-combustion of a mixture of biomass with coal in a fluidized bed combustor designed for coal combustion increased combustion efficiency up to 20% depending upon excess air levels. Observed carbon monoxide levels fluctuated between 200 and 900 ppm with the addition of coal. It is evident from this research that efficient co-firing of biomass with coal can be achieved with minimal modifications to existing coal-fired boilers.
The paper reports on the performance of chromium or/and copper supported on H-ZSM-5(Si/Al = 240) modified with silicon tetrachloride (Cr1.5/SiCl4-Z, Cu1.5/SiCl4-Z and Cr1.0Cu0.5/SiCl4-Z) as catalysts in the combustion of chlorinated VOCs (Cl-VOCs). A reactor operated at a gas hourly space velocity (GHSV) of 32,000 h(-1), a temperature between 100 and 500 degrees C with 2500 ppm of dichloromethane (DCM), trichloromethane (TCM) and trichloroethylene (TCE) is used for activity studies. The deactivation study is conducted at a GHSV of 3800 h(-1), at 400 degrees C for up to 12 h with a feed concentration of 35,000 ppm. Treatment with silicon tetrachloride improves the chemical resistance of H-ZSM-5 against hydrogen chloride. TCM is more reactive compared to DCM but it produces more by-products due to its high chlorine content. The stabilization of TCE is attributed to resonance effects. Water vapor increases the carbon dioxide yield through its role as hydrolysis agent forming reactive carbocations and acting as hydrogen-supplying agent to suppress chlorine-transfer reactions. The deactivation of Cr1.0Cu0.5/SiCl4-Z is mainly due to the chlorination of its metal species, especially with higher Cl/H feed. Coking is limited, particularly with DCM and TCM. In accordance with the Mars-van Krevelen model, the weakening of overall metal reducibility due to chlorination leads to a loss of catalytic activity.
Fibres have been used in construction materials for a very long time. Through previous research and investigations, the use of natural and synthetic fibres have shown promising results, as their presence has demonstrated significant benefits in terms of the overall physical and mechanical properties of the composite material. When comparing fibre reinforcement to traditional reinforcement, the ratio of fibre required is significantly less, making fibre reinforcement both energy and economically efficient. More recently, waste fibres have been studied for their potential as reinforcement in construction materials. The build-up of waste materials all around the world is a known issue, as landfill space is limited, and the incineration process requires considerable energy and produces unwanted emissions. The utilisation of waste fibres in construction materials can alleviate these issues and promote environmentally friendly and sustainable solutions that work in the industry. This study reviews the types, properties, and applications of different fibres used in a wide range of materials in the construction industry, including concrete, asphalt concrete, soil, earth materials, blocks and bricks, composites, and other applications.
In order to address slagging, fouling and high-temperature corrosion problems caused by alkali metals in Municipal Solid Waste (MSW), in-situ measurement of alkali metal in MSW incinerators is needed. The paper presents experimental measurements of temperatures and alkali metal concentrations in two MSW incinerators based on Flame Emission Spectroscopy (FES). Through the analysis of spontaneous emission spectra and a calibration procedure, the concentration of gas phase sodium (Na) and potassium (K), temperature and thermal radiation in the incinerator were in-situ measured by a portable spectral system simultaneously. Experimental results showed MSW composition has significant effect on the measured gaseous Na and K. Higher volatile content in MSW may enhance the alkali metal emission. Besides that, the released gaseous Na and K in the two incinerators are correlated with temperature in incinerators. The study provided a low cost and effective solution for in-situ measurement of temperature and alkali metal concentration in MSW incinerators.
Improper healthcare waste (HCW) management poses significant risks to the environment, human health, and socio-economic sustainability due to the infectious and hazardous nature of HCW. This research aims at rendering a comprehensive landscape of the body of research on HCW management by (i) mapping the scientific development of HCW research, (ii) identifying the prominent HCW research themes and trends, and (iii) providing a research agenda for HCW management towards a circular economy (CE) transition and sustainable environment. The analysis revealed four dominant HCW research themes: (1) HCW minimization, sustainable management, and policy-making; (2) HCW incineration and its associated environmental impacts; (3) hazardous HCW management practices; and (4) HCW handling and occupational safety and training. The results showed that the healthcare industry, despite its potential to contribute to the CE transition, has been overlooked in the CE discourse due to the single-use mindset of the healthcare industry in the wake of the infectious, toxic, and hazardous nature of HCW streams. The findings shed light on the HCW management domain by uncovering the current status of HCW research, highlighting the existing gaps and challenges, and providing potential avenues for further research towards a CE transition in the healthcare industry and HCW management.
Most households and healthcare facilities usually dispose of contaminated, unused, or expired (CUE) medicines with municipal wastes, the disposal of which usually amounts to $790/ton in the USA and £450/ton in the UK. Solid (e.g., tablets, capsules, powders) and semi-solid (e.g., ointment, creams) pharmaceuticals are managed with incineration/pyrolysis, encapsulation, and engineered landfills, whereas wastewater treatment plants (WWTPs) are recommended for liquid pharmaceutical wastes (PWs). However, to date, the sustainability and eco-friendliness profile of these techniques are only subjectively ensured, leading to controversial viewpoints in many guidelines. Each technique has relative strengths and weaknesses, and their comparative weighting to maximize these profiles is sought after. The present comprehensive review aims to fulfil knowledge gaps in this regard. Four electronic databases (e.g., PubMed/MEDLINE, Scopus, and ScienceDirect) were searched for PW management (PWM)-related qualitative and quantitative articles published till December 31, 2022. Articles without details of waste disposal techniques and their health and environmental impacts were excluded. Based on the literature review, we determine that incineration can be considered a sustainable option for solid and semi-solid PWs, and WWTPs can be eco-friendly for liquid PWs, whereas encapsulation and landfilling are less sustainable. It is high time that objectively proven sustainable and eco-friendly techniques be implemented for PWM based on their dosage forms or nature of hazards. Medicine take-back, eco-pharmacovigilance, extended producer responsibility, co-payment, and life cycle analysis of pharmaceuticals focusing on reduction, reuse/re-dispensing can be integrated to make existing models sustainable, circular, and eco-friendly.
Recently, various solid wastes from industry such as glass waste, fly ash, sewage sludge and slag have been recycled into various value-added products such as ceramic tile. The conventional solutions of dumping the wastes in landfills or incineration, including in Malaysia are getting obsolete as the annual huge amount of the solid wastes would boost-up disposal cost and may cause permanent damage to the flora and fauna. This recent waste recycling approach is much better and greener as it can resolve problems associated with over-limit storage of industrial wastes and reduce exploration of natural resources for ceramic tile to continuously sustain the nature. Therefore, in this project, an attempt was made to recycle electric arc furnace (EAF) slag waste, obtained from Malaysia's steel making industry, into ceramic tile via conventional powder compaction method. The research work was divided into two stages. The first stage was to evaluate the suitability of EAF slag in ceramic tile by varying weight percentage of EAF slag (40 wt.%, 50 wt.% and 60 wt.%) and ball clay (40 wt.%, 50 wt.% and 60 wt.%), with no addition of silica and potash feldspar. In the second stage, the weight percentage of EAF slag was fixed at 40 wt.% and the percentage of ball clay (30 wt.% and 40 wt.%), feldspar (10 wt.% and 20 wt.%) and silica (10 wt.% and 20 wt.%) added was varied accordingly. Results obtained show that as weight percentage of EAF slag increased up to 60 wt.%, the percentage of apparent porosity and water absorption also rose, with a reduction in tile flexural strength and increased porosity. On the other hand, limiting the weight percentage of EAF slag to 40 wt.% while increasing the weight percentage of ball clay led to a higher total percentage of anorthite and wollastonite minerals, resulting in higher flexural strength. It was found that introduction of silica and feldspar further improved the flexural strength due to optimization of densification process. The highest flexural strength, lowest apparent porosity and water absorption of EAF slag based tile was attained at the composition of 40 wt.% EAF slag--30 wt.% ball clay--10 wt.% feldspar--20 wt.% silica. The properties of ceramic tile made with EAF slag waste (up to 40 wt.%), especially flexural strength are comparable to those of commercial ceramic tile and are, therefore, suitable as high flexural strength and heavy-duty green ceramic floor tile. Continuous development is currently underway to improve the properties of tile so that this recycling approach could be one of the potential effective, efficient and sustainable solutions in sustaining our nature.
Thermal performance, combustibility, and fire propagation of fly ash-metakaolin (FA-MK) blended geopolymer with the addition of aluminum triphosphate, ATP (Al(H2PO4)3), and monoaluminium phosphate, MAP (AlPO4) were evaluated in this paper. To prepare the geopolymer mix, fly ash and metakaolin with a ratio of 1:1 were added with ATP and MAP in a range of 0-3% by weight. The fire/heat resistance was evaluated by comparing the residual compressive strengths after the elevated temperature exposure. Besides, combustibility and fire propagation tests were conducted to examine the thermal performance and the applicability of the geopolymers as passive fire protection. Experimental results revealed that the blended geopolymers with 1 wt.% of ATP and MAP exhibited higher compressive strength and denser geopolymer matrix than control geopolymers. The effect of ATP and MAP addition was more obvious in unheated geopolymer and little improvement was observed for geopolymer subjected to elevated temperature. ATP and MAP at 3 wt.% did not help in enhancing the elevated-temperature performance of blended geopolymers. Even so, all blended geopolymers, regardless of the addition of ATP and MAP, were regarded as the noncombustible materials with negligible (0-0.1) fire propagation index.
Polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) are toxic compounds derived from anthropogenic sources that stay in the environment for long periods. Ambient air has become the most important pathway for the transfer of PCDDs/PCDFs from emission sources to the environment. This review intends to summarise the information available on atmospheric PCDDs/PCDFs in the countries of Southeast Asia to provide a detailed description of the trends in PCDDs/PCDFs emissions, key sources, and levels in urban, rural, and industrial air as reported in peer-reviewed literature since 2000 and by the United Nations Environment Programme. As the largest country in Southeast Asia, Indonesia is the major PCDDs/PCDFs emitter, accounting for 72.81% of the total release of PCDDs/PCDFs in the air from all available inventories in this region, while Brunei Darussalam is the lowest emitter, contributing to less than 0.02%. Open burning processes have become the largest source of ambient PCDDs/PCDFs in the region (69.62%), followed by waste incineration (10.69%), and ferrous and non-ferrous metal production (8.78%). PCDDs/PCDFs levels in rural areas ranged between 10 and 38 fg TEQ m-3; however, where open burning waste has occurred, the levels rose to 12-29 times higher. In urban areas, ambient levels were 15 times greater than in rural areas, varying from 23 to 565 fg TEQ m-3. Atmospheric concentrations near industrial palm oil and waste incinerator sites were between 64 and 1530 fg TEQ m-3. The non-cancer risk of ambient exposure to PCDDs/PCDFs through inhalation is low among populations near facilities emitting PCDDs/PCDFs. The lack of local technical capacity, the high economic costs, and the lack of established human resource capacities have been the major challenges in conducting ambient PCDDs/PCDFs studies in most countries in the region.
The increasing amount of food waste in Malaysia in recent years has brought many environmental
issues in the country where it affects the nation’s solid waste management framework. At the
moment, the government is limited to other alternatives of food waste disposal besides the
conventional landfill and incineration methods. This paper provides information on the current
status of food waste handling, management, regulations, and policies in Malaysia. It helps
to draw the problem and challenge to a clearer view in efforts of achieving sustainable and
integrative food waste handling in the country.
The presence of heavy metals in aquatic systems has become a serious problem. Heavy metals can haveadverse effects on the environment as well as on human health. As a result, much attention has beengiven to new technologies for removal of heavy metal ions from contaminated waters. In this study,Microwave Incinerated Rice Husk Ash (MIRHA), a locally available agricultural waste, was used for theremoval of Cd (as a representative heavy metal) from synthetic wastewater by batch adsorption process.The effects of pH, initial metal concentration, and contact time on Cd removal efficiency were studied.pH 4 was found to be the optimum. The removal efficiency was found to be correlated with the initialmetal concentration and contact time between adsorbent and adsorbate. Cd adsorption kinetics followedthe pseudo-second-order model and implied chemisorption. The adsorption equilibrium of Cd can bewell described by the Freundlich isotherm model.
Mercury emission into the atmosphere is a global concern due to its detrimental effects on human health in general. The two main sources of mercury emission are natural sources and anthropogenic sources. Mercury emission from natural sources include volcanic activity, weathering of rocks, water movement and biological processes which are obviously inevitable. The anthropogenic sources of mercury emission are from coal combustion, cement production and waste incineration. Thus, in order to reduce mercury emission it is appropriate to investigate how mercury is released from the anthropogenic sources and consequently the mercury removal technology that can be implemented in order to reduce mercury emission into the atmosphere. Many alternatives have been developed to reduce mercury emission and the recent application of activated carbon showed high potential in the adsorption of elemental mercury. This paper discusses the ability of activated carbon and variable parameters that influence mercury removal efficiency in flue gas.
Incineration and disposal of carbon fiber waste from the aircraft industry lead to serious energy consumption and environmental pollution. The use of this waste as reinforcement is a wise approach to appreciate the high performance of the carbon fiber. This study is part of our effort to develop new green rubber foam from recycled carbon fiber prepreg (rCFP) reinforced natural rubber via internal mixer. It is focusing on the effect of different rCFP loading at 1, 3, 5, and 7 parts per hundred rubbers (phr) as reinforcement. The samples were prepared by melt compounding using an internal mixer and expanded via two step heat transfer foaming process. The physical properties of the green rubber foam were characterized and the results were observed to systematically correlate with the impact properties of the foam. The absorbed energy of the foam increases up to 0.3 joules with increasing relative foam density of 0.81 which is associated with the formation of smaller foam cells ~0.68mm and more spherical shape pores.