Silicon dioxide (SiO2) is the most widely used dielectric for electronic applications. It is usually produced by thermal oxidation of silicon or by using a wide range of vacuum-based techniques. By default, the growth of SiO2 by thermal oxidation of silicon requires the use of Si substrates whereas the other deposition techniques either produce low quality or poor interface material and mostly require high deposition or annealing temperatures. Recent investigations therefore have focused on the development of alternative deposition paradigms based on solutions. Here, we report the deposition of SiO2 thin film dielectrics deposited by spray pyrolysis in air at moderate temperatures of ≈350 °C from pentane-2,4-dione solutions of SiCl4. SiO2 dielectrics were investigated by means of UV-vis absorption spectroscopy, spectroscopic ellipsometry, XPS, XRD, UFM/AFM, admittance spectroscopy, and field-effect measurements. Data analysis reveals smooth (RRMS < 1 nm) amorphous films with a dielectric constant of about 3.8, an optical band gap of ≈8.1 eV, leakage current densities in the order of ≈10(-7) A/cm(2) at 1 MV/cm, and high dielectric strength in excess of 5 MV/cm. XPS measurements confirm the SiO2 stoichiometry and FTIR spectra reveal features related to SiO2 only. Thin film transistors implementing spray-coated SiO2 gate dielectrics and C60 and pentacene semiconducting channels exhibit excellent transport characteristics, i.e., negligible hysteresis, low leakage currents, high on/off current modulation ratio on the order of 10(6), and high carrier mobility.
The use of sustainable materials in the construction industry has been on the rise recently. Studies have proven that the use of conventional concrete and its raw materials has a negative impact on the environment. Research on incorporating biochar as a supplementary cementitious material has been recently evolving and has shown that the attributes of biochar are highly affected by the pyrolysis parameters. These attributes have enhanced the properties of biochar concrete and mortar composite. This paper identifies the different physiochemical properties exhibited by palm kernel shell biochar through optimization by response surface methodology. Focusing on some of the properties of biochar that have proven beneficial when used as a cement replacement. Very limited research has used optimization tools for the production of biochar with the intention of using it as a cement substitute. Pyrolysis was conducted by a tubular furnace at different temperature ranges from 200 °C to 800 °C. The biomass and biochar have been analyzed with TGA and FESEM-EDX. The targeted biochar properties and selected responses are the yield, carbon, oxygen, silica, and potassium content. The optimized parameters obtained are 409 °C, 15 °C/min, 120 min with responses of 38.2% yield, 73.37% carbon, 25.48% oxygen, 0.39% potassium and 0.44% silica. Thermal properties of the palm kernel shell biochar affected by the pyrolysis factors such as temperature, heating rate and residence time have also been discussed. In conclusion, this study supports and encourages the use of palm waste, which is abundant in Malaysia, as a supplementary cementitious material to promote sustainable growth in construction.
In recent years, plasma-assisted synthesis has been extensively used in large scale production of functional nano- and micro-scale materials for numerous applications in optoelectronics, photonics, plasmonics, magnetism and drug delivery, however systematic formation of these minuscule structures has remained a challenge. Here we demonstrate a new method to closely manipulate mesostructures in terms of size, composition and morphology by controlling permeability at the boundaries of an impermeable plasma surrounded by a blanket of neutrals. In situ and rapid growth of thin films in the core region due to ion screening is among other benefits of our method. Similarly we can take advantage of exceptional properties of plasma to control the morphology of the as deposited nanostructures. Probing the plasma at boundaries by means of observing the nanostructures, further provides interesting insights into the behaviour of gas-insulated plasmas with possible implications on efficacy of viscous heating and non-magnetic confinement.
This study analyzes the performance of two PV modules, amorphous silicon (a-Si) and crystalline silicon (c-Si) and predicts energy yield, which can be seen as facilitation to achieve the target of 35% reduction of greenhouse gases emission by 2030. Malaysia Energy Commission recommends crystalline PV modules for net energy metering (NEM), but the climate regime is a concern for output power and efficiency. Based on rainfall and irradiance data, this study aims to categorize the climate of peninsular Malaysia into rainy and dry seasons; and then the performance of the two modules are evaluated under the dry season. A new mathematical model is developed to predict energy yield and the results are validated through experimental and systematic error analysis. The parameters are collected using a self-developed ZigBeePRO-based wireless system with the rate of 3 samples/min over a period of five days. The results unveil that efficiency is inversely proportional to the irradiance due to negative temperature coefficient for crystalline modules. For this phenomenon, efficiency of c-Si (9.8%) is found always higher than a-Si (3.5%). However, a-Si shows better shadow tolerance compared to c-Si, observed from a lesser decrease rate in efficiency of the former with the increase in irradiance. Due to better spectrum response and temperature coefficient, a-Si shows greater performance on output power efficiency (OPE), performance ratio (PR), and yield factor. From the regression analysis, it is found that the coefficient of determination (R2) is between 0.7179 and 0.9611. The energy from the proposed model indicates that a-Si yields 15.07% higher kWh than c-Si when luminance for recorded days is 70% medium and 30% high. This study is important to determine the highest percentage of energy yield and to get faster NEM payback period, where as of now, there is no such model to indicate seasonal energy yield in Malaysia.
A novel thin-film multijunction solar cell based on nanocrystalline silicon (nc-Si:H) is presented in this paper. Existing thin-film double junction solar cells are based on amorphous silicon carbide (aSiC:H) and amorphous silicon layers. Such solar cells have limited efficiency due to lower absorption and poor charge transport properties of the a-SiC:H layer. These solar cells have maximum achieved efficiency of about 8.8%. In this work, a-SiC:H has been replaced with nc-Si:H layer and the double junction solar cell has been redesigned. The proposed structure has been simulated with Silvaco TCAD (ATLAS). The simulated results indicated a step increase in the performance of the solar cell with open circuit voltage Voc=2 .096 V and efficiency 77 = 102%. It was proven that the nc-Si:H is a suitable material for the development of an efficient thin film multijunction solar cell.
Polysulfone (PSF) based mixed matrix membranes (MMMs) are one of the most broadly studied polymeric materials used for CO2/CH4 separation. The performance of existing PSF membranes encounters a bottleneck for widespread expansion in industrial applications due to the trade-off amongst permeability and selectivity. Membrane performance has been postulated to be enhanced via functionalization of filler at different weight percentages. Nonetheless, the preparation of functionalized MMMs without defects and its empirical study that exhibits improved CO2/CH4 separation performance is challenging at an experimental scale that needs prior knowledge of the compatibility between the filler and polymer. Molecular simulation approaches can be used to explore the effect of functionalization on MMM's gas transport properties at an atomic level without the challenges in the experimental study, however, they have received less scrutiny to date. In addition, most of the research has focused on pure gas studies while mixed gas transport properties that reflect real separation in functionalized silica/PSF MMMs are scarcely available. In this work, a molecular simulation computational framework has been developed to investigate the structural, physical properties and gas transport behavior of amine-functionalized silica/PSF-based MMMs. The effect of varying weight percentages (i.e., 15-30 wt.%) of amine-functionalized silica and gas concentrations (i.e., 30% CH4/CO2, 50% CH4/CO2, and 70% CH4/CO2) on physical and gas transport characteristics in amine-functionalized silica/PSF MMMs at 308.15 K and 1 atm has been investigated. Functionalization of silica nanoparticles was found to increase the diffusion and solubility coefficients, leading to an increase in the percentage enhancement of permeability and selectivity for amine-functionalized silica/PSF MMM by 566% and 56%, respectively, compared to silica/PSF-based MMMs at optimal weight percentage of 20 wt.%. The model's permeability differed by 7.1% under mixed gas conditions. The findings of this study could help to improve real CO2/CH4 separation in the future design and concept of functionalized MMMs using molecular simulation and empirical modeling strategies.
Biomass, which defined as plant- or animal-based materials, is intriguing tremendous scientific attentions due to its renewable attribute in serving energy security. Amongst, the plant-based biomasses, particularly those that co-generated in the agriculture activities, are commonly regarded as fuel for burning, which overlooked their hidden potentials for high-end applications. Organically, the plant-based biomass constitutes of lignocellulose components, which can be served as promising precursors for functionalized carbon materials. Meanwhile, its inorganic counterpart made up of various minerals, with Si being the most concerned one. With the advancement of biomass technologies and material synthesis in recent years, numerous attempts were endeavoured to obtain valorised products from biomass. Particularly, syntheses of catalytic and adsorptive materials are actively researched in the field of biomass reutilization. Herein, our work systematically summarized the advancements of biomass-materials for these applications in recent 10 years (2010-2020), with a special focus on the carbon-based and Si-based catalytic/adsorptive materials. Significantly, the deriving steps, inclusive of both pre-treatment and post-treatment of such materials, are incorporated in the discussion, alongside with their significances revealed too. The performance of the as-obtained materials in the respective application is systematically correlated to their physicochemical properties, hence providing valuable insights to the readers. Challenges and promising directions to be explored are raised too at the end of the review, aiming to advocate better-usage of biomass while offering great opportunities to sustain catalysis and adsorption in the industrial scale.
Ternary CuO/AgO/FSZr photocatalysts were fabricated via the hydrothermal and electrochemical methods with three different CuO loading (1, 3 and 5 wt%), indicated as 1CuO/AgO/FSZr, 3CuO/AgO/FSZr and 5CuO/AgO/FSZr. The photocatalytic reaction was tested towards simultaneous chromium (VI) photoreduction and p-cresol photooxidation and the performance in order as follow: 3CuO/AgO/FSZr > 5CuO/AgO/FSZr > 1CuO/AgO/FSZr > AgO/FSZr > FSZr. CuO/AgO/FSZr photocatalysts showed an improvement in photocatalytic activity compared to AgO/FSZr and FSZr due to the reduction potential of chromium (VI) aligned closer to the conduction band of CuO and provided abundant free active electrons (e-) and holes (h+) with efficient transportation and migration. Interestingly, the 3CuO/AgO/FSZr was established as the best photocatalyst with 98% reduction of chromium (VI) and 83% oxidation of p-cresol simultaneously, owing to its strong corporation between the metal oxides and support and higher total pore volume. The Langmuir-Hinshelwood model were employed for kinetics which followed the pseudo-first-order kinetics model well. Based on the simultaneous photocatalytic mechanism, chromium (VI) and p-cresol were directly reduced and oxidized by e- and h+, respectively. The response surface methodology (RSM) discovered that the quadratic term initial concentration of chromium (VI) is the main significant factor in photocatalytic performance. The optimum parameters for simultaneous photoredox of chromium (VI) and p-cresol predicted from RSM are 9.6 mg L-1 of chromium (VI) concentration, 9.8 mg L-1 of p-cresol concentration and 0.32 g L-1 of catalyst dosage. Under these conditions the error between the predicted and experimental values is only 3.7%. The 3CuO/AgO/FSZr sustained the photocatalytic performance after reused for five cycles and could oxidized various organic pollutants as well as reduced chromium (VI) simultaneously.
Air gasification of the Wood-Plastic Composite (WPC) was performed over Ni-loaded HZSM-5 catalysts to generate H2-rich gas. Increasing SiO2/Al2O3 ratio (SAR) of HZSM-5 adversely affected catalytic activity, where the highest gas yield (51.38 wt%) and H2 selectivity (27.01 vol%) were acquired using 20 %Ni/HZSM-5(30) than those produced over 20 %Ni/HZSM-5(80) and 20 %Ni/HZSM-5(280). Reducing SAR was also favorably conducive to increasing the acyclic at the expense of cyclic compounds in oil products. These phenomena are attributed to enhanced acid strength and Ni dispersion of 20 %Ni/HZSM-5(30) catalyst. Moreover, catalytic activity in the terms of gas yield and H2 selectivity enhanced with growing Ni loading to 20 %. Also, the addition of promoters (Cu and Ca) to 20 %Ni/HZSM-5(30) boosted the catalytic efficiency for H2-rich gas generation. Raising temperature indicated a positive relevance with the gas yield and H2 selectivity. WPC valorization via gasification technology would be an outstanding outlook in the terms of a waste-to-energy platform.
Epoxy resins are important thermosetting polymers. They are widely used in many applications i.e., adhesives, plastics, coatings and sealers. Epoxy molding compounds have attained dominance among common materials due to their excellent mechanical properties. The sol-gel simple method was applied to distinguish the impact on the colloidal time. The properties were obtained with silica-based fillers to enable their mechanical and thermal improvement. The work which we have done here on epoxy-based nanocomposites was successfully modified. The purpose of this research was to look into the effects of cellulose nanocrystals (CNCs) on various properties and applications. CNCs have recently attracted a lot of interest in a variety of industries due to their high aspect ratio, and low density which makes them perfect candidates. Adding different amounts of silica-based nanocomposites to the epoxy system. Analyzed with different techniques such as Fourier-transformed infrared spectroscope (FTIR), thermogravimetric analysis (TGA) and scanning electronic microscopic (SEM) to investigate the morphological properties of modified composites. The various %-age of silica composite was prepared in the epoxy system. The 20% of silica was shown greater enhancement and improvement. They show a better result than D-400 epoxy. Increasing the silica, the transparency of the films decreased, because clustering appears. This shows that the broad use of CNCs in environmental engineering applications is possible, particularly for surface modification, which was evaluated for qualities such as absorption and chemical resistant behavior.
Transport of environmental pollutants in groundwater systems can be greatly influenced by colloids. In this study, the cotransport of Pb2+ and silica (SiO2) colloids at different Pb2+ concentrations was systematically investigated by batch adsorption and saturated sand column experiments. Results showed that SiO2 colloids had low adsorption capacity for Pb2+ (less than 1% of the input) compared with sands. In saturated porous media, SiO2 colloids showed a high mobility; however, with the increase of Pb2+ concentration in the sand column, the mobility of SiO2 colloids gradually decreased. Notably, SiO2 colloids could facilitate Pb2+ transport, although they did not serve as effective carriers of Pb2+. Under the condition of low Pb2+ concentration, SiO2 colloids promoted the Pb2+ transport mainly through the way of "transport channel," while changing the porosity of the medium and masking medium adsorption sites were the main mechanisms of SiO2 colloid-facilitated Pb2+ transport under the condition of high Pb2+ concentration. The discovery of this non-adsorption effect of colloids would improve our understanding of colloid-facilitated Pb2+ transport in saturated porous media, which provided new insights into the role of colloids, especially colloids with weak Pb2+ adsorption capacity, in Pb2+ occurrence and transport in soil-groundwater systems.
The borehole coal samples of Dhulia North Block from the Rajmahal Basin, Eastern India, were systematically analyzed based on the chemical composition and concentration of major and trace elements (including rare earth elements, REEs) to assess the distribution of REEs and their environmental implications with utilization potential. The Dhulia North Block coals are characterized by the predominant major oxides of SiO2, Al2O3, and Fe2O3, accounting for 94% of the total ash composition, indicating the presence of quartz, clay-rich minerals, and pyrite. Compared with the average world coal ash, the total REE content in the analyzed samples ranged from 341.0 to 810.4 ppm, which is substantially higher. Hot humid climate conditions with intermediate igneous source rocks of the basin were demonstrated by the major oxide ratios (Al2O3/TiO2 < 20) and plots of TiO2 with Al2O3 and Zr. The redox-sensitive elements such as V, Ni, Cr, and Co found in the Dhulia North Block coal indicate that an oxic sedimentary environment existed in the basin when coal was formed. The low sulfur content (1% in most samples) indicates freshwater conditions in the basin at the time of organic matter deposition. The outlook coefficient (Coutl) varies between 0.7 and 1.6, indicating that the Dhulia North Block coals are a prospective source of REEs. The Dhulia North Block coals are characterized by low H/C and O/C atomic ratios ranging from 0.56 to 0.90 and 0.10 to 0.22, respectively, and contain type-III kerogens, indicating gas-prone source rock. Further, the basic-to-acid oxide ratio suggested that Dhulia North Block coals were suitable for utilization during combustion processes.
Since its invention, polyimide (PI) has been widely used in micro-electro-mechanical system (MEMS) devices. For fabrication, the PI membrane, PI-2723 HD-Microsystems was used as the membrane material due to its Young's modulus of 2.7 GPa and its film thickness could easily be controlled by changing the speed of the spin coater system. The application PI as membrane structure on silicon wafers therefore gave a much better mechanical performance then conventional membranes made of silicon dioxide (SiO2) or silicon nitride (Si3N4) layers. The fabrication of PI membrane was the same as for SiO2 and Si3N4 membranes; the basic step was to etch a side of the silicon wafer using wet anisotropic etching. This paper proposes an effective process for fabrication of PI membrane with f ast and little supervision. In this process, a dual step process was wet anisotropic etching of single crystal silicon using pottasium hydroxyl (KOH) with different concentrations and temperature processes. For the first process, 45% KOH under boiling temperature was used to etch at least 90%–95% of the silicon. In the second process, the silicon was submerged in 45% KOH with temperature at 70ºC–80ºC to etch away the residual silicon until a clean and transparent PI membrane was achieved. Using this method, the fabrication of PI membrane could be generated fast.
We have calculated the vibrational frequencies of clusters of atoms from the first principles by using the density-functional theory in the local density approximation (LDA). We are also able to calculate the electronic binding energy for all of the clusters of atoms from the optimized structure. We have made clusters of BanOm (n, m=1-6) and have determined the bond lengths, vibrational frequencies as well as intensities in each case. We find that the peroxide cluster BaO2 occurs with the O-O vibrational frequency of 836.3 cm(-1). We also find that a glass network occurs in the material which explains the vibrational frequency of 67 cm(-1). The calculated values agree with those measured from the Raman spectra of barium peroxide and Ba-B-oxide glass. We have calculated the vibrational frequencies of BaO4, GeO4 and SiO4 each in tetrahedral configuration and find that the vibrational frequencies in these systems depend on the inverse square root of the atomic mass.
Hard rock formations consisting of granite and metasedimentary rocks in Peninsular Malaysia, have beenconsidered to be of poor aquifers. The map of shows the area underlain by hard rock as having poorto moderate potential for groundwater production (
This work demonstrated a growth of well-aligned NiSi/SiC core-shell nanowires by a one-step process of hot-wire chemical vapor deposition on Ni-coated crystal silicon substrates at different thicknesses. The NiSi nanoparticles (60 to 207 nm) acted as nano-templates to initially inducing the growth of these core-shell nanowires. These core-shell nanowires were structured by single crystalline NiSi and amorphous SiC as the cores and shells of the nanowires, respectively. It is proposed that the precipitation of the NiSi/SiC are followed according to the nucleation limited silicide reaction and the surface-migration respectively for these core-shell nanowires. The electrical performance of the grown NiSi/SiC core-shell nanowires was characterized by the conducting AFM and it is found that the measured conductivities of the nanowires were higher than the reported works that might be enhanced by SiC shell layer on NiSi nanowires. The high conductivity of NiSi/SiC core-shell nanowires could potentially improve the electrical performance of the nanowires-based devices for harsh environment applications such as field effect transistors, field emitters, space sensors, and electrochemical devices.
Rice brown spot (BS) exerts devastating agronomic effects on grain quality and overall productivity. In Peninsular Malaysia, BS disease incidence is fairly prevalent and little is known about the diversity of BS pathogens in the local granaries. Fifteen isolates from BS symptomatic rice plants were identified at five different rice granaries across Peninsular Malaysia. Based on the morphological and molecular analyses, two isolates were confirmed as Bipolaris oryzae while the rest were identified as Exserohilum rostratum. Phylogenetic tree analysis revealed that BS incidence in rice granaries in Peninsular Malaysia is caused by a pair of closely related fungal pathogens, E. rostratum and B. oryzae, with the former being more predominant. Cultural characterization of E. rostratum isolate KT831962 showed the best growth and sporulation activity on corn meal agar plates incubated in complete darkness. The effects of calcium silicate (CaSiO3) and rice husk ash (RHA) soil amendment against MR219 and MR253 rice varieties were evaluated during rice-E. rostratum interaction. Results showed that soil amelioration using CaSiO3 and RHA singly and in combination with manganese (Mn) significantly reduced rice BS disease severity. The BS disease index was reduced significantly to less than 31.6% in the silicon-treated rice plants relative to the control plants at 41.2%. Likewise, the grain yield at the harvest stage showed significantly higher yield in the Si-treated rice plants in comparison to the control, non-Si treated rice plants. The findings highlight the potential of RHA agro-waste as Si fertilizer in a sustainable rice production system.
Silicon (Si) is one of the most prevalent macroelements, performing an essential function in healing plants in response to environmental stresses. The purpose of using Si is to induce resistance to distinct stresses, diseases, and pathogens. Additionally, Si can improve the condition of soils, which contain toxic levels of heavy metals along with other chemical elements. Silicon minimizes toxicity of Fe, Al, and Mn, increases the availability of P, and enhances drought along with salt tolerance in plants through the formation of silicified tissues in plants. However, the concentration of Si depends on the plants genotype and organisms. Hence, the physiological mechanisms and metabolic activities of plants may be affected by Si application. Peptides as well as amino acids can effectively create polysilicic species through interactions with different species of silicate inside solution. The carboxylic acid and the alcohol groups of serine and asparagine tend not to engage in any significant role in polysilicates formation, but the hydroxyl group side chain can be involved in the formation of hydrogen bond with Si(OH)4. The mechanisms and trend of Si absorption are different between plant species. Furthermore, the transportation of Si requires an energy mechanism; thus, low temperatures and metabolic repressors inhibit Si transportation.