The pollution of the world's water resources is a growing issue which requires remediation. Surfactants used in many domestic and industrial applications are one of the emerging contaminants that require immediate attention. Treating water contaminated with surfactants using adsorption provides better performance when compared to other techniques. A variety of materials have been developed for adsorbing surfactants. Activated carbon is the most suitable adsorbent for removing surfactants but is expensive to synthesize and difficult to regenerate. Therefore, a variety of new adsorbents such as zeolites, nanomaterials, resins, biomaterials and clays have been developed as alternatives. The developed adsorbents are promising but considerable research is still required to develop highly efficient, economical, environment friendly and sustainable adsorbents to replace activated carbon. This paper critically reviews the characteristics of adsorbents, the performance of adsorbents, kinetics, isotherms and thermodynamics, mechanisms of adsorption, regeneration of adsorbents and future perspectives in the adsorption of surfactants. Developing novel adsorbents, testing adsorbents in real wastewaters and recycling the adsorbents are required in future studies in the removal of surfactants.
Extensive effort has been focused on the advancement of an efficient catalyst for CO2 reforming of CH4 to achieve optimum catalytic activity together with cost-effectiveness and high resistance to catalyst deactivation. In this study, for the first time, a new catalytic support/catalyst system of bifunctional NiO/dolomite has been synthesized by a wet impregnation method using low-cost materials, and it shows unique performance in terms of amphoteric sites and self-reduction properties. The catalysts were loaded into a continuous micro-reactor equipped with an online GC-TCD system. The reaction was carried out with a gas mixture consisting of CH4 and CO2 in the ratio of 1 : 1 flowing 30 ml min-1 at 800 °C for 10 h. The physicochemical properties of the synthesized catalysts were determined by various methods including X-ray diffraction (XRD), N2 adsorption-desorption, H2 temperature-programmed reduction (H2-TPR), temperature-programmed desorption of CO2 (TPD-CO2), and temperature-programmed desorption of NH3 (TPD-NH3). The highest catalytic performance of the DRM reaction was shown by the 10% NiO/dolomite catalyst (CH4 & CO2 conversion, χCH4; χCO2 ∼ 98% and H2 selectivity, S H2 = 75%; H2/CO ∼ 1 : 1 respectively). Bifunctional properties of amphoteric sites on the catalyst and self-reduction behaviour of the NiO/dolomite catalyst improved dry reforming of the CH4 process by enhancing CH4 and CO2 conversion without involving a catalyst reduction step, and the catalyst was constantly active for more than 10 h.
Alkali sludge (AS) is waste abundantly generated from solar photovoltaic (PV) solar cell industries. Since this potential basic material is still underutilized, a combination with NiO catalyst might greatly influence coke resentence, especially in high-temperature thermochemical reactions (Arora and Prasad, RSC Adv. 6:108,668-108688, 2016). This paper investigated alkaline sludge containing 3CaO-2SiO2 doped with well-known NiO to enhance the dry reforming of methane (DRM) reaction. The wet-impregnation method was used to prepare the xNiO/AS (x = 5-15%) catalysts. Subsequently, all catalysts were tested by using X-ray diffraction (XRD), nitrogen adsorption/desorption (BET), temperature-programmed reduction of hydrogen (H2-TPR), temperature-programmed desorption of carbon dioxide (TPD-CO2), field emission scanning electron microscopy (FESEM-EDX), and X-ray photoelectron spectroscopy (XPS). The spent catalysts were analyzed by thermogravimetric analysis (TGA/DTG), transmission electron microscopy (TEM), and temperature-programmed oxidation (TPO). The catalytic performance of xNiO/AS catalysts was investigated in a fixed bed reactor connected with gas chromatography thermal conductivity detector (GC-TCD) at a CH4:CO2 flow rate of 30 mL-1 during a 10-h reaction by following (Shamsuddin et al., Int. J. Energy Res. 45:15,463-15,480, 2021d). For optimization parameters, the effects of NiO concentration (5, 10, and 15%), reaction temperature (700, 750, 800, 850, and 900 °C), catalyst loading (0.1, 0.2, 0.3, 0.4, and 0.5 g), and gas hourly space velocity (GHSV) range from 3000, 6000, 9000, 12,000, and 15,000 h-1 were evaluated. The results showed that physical characteristics such as BET surface area and porosity do not significantly impact NiO percentages of dispersion, whereas chemical characteristics like reducibility are crucial for the catalysts' efficient catalytic activity. Due to the active sites on the catalyst surface being more accessible, increased NiO dispersion resulted in higher reactant conversion. The catalytic performance on various parameters that showed 15%NiO/AS exhibited high reactant conversion up to 98% and 40-60% product selectivity in 700 °C, 0.2 g catalyst loading, and 12,000 h-1 GHSV. According to spent catalyst analyses, the catalyst was stable even after the DRM reaction. Meanwhile, increased reducibility resulted in more and better active site formation on the catalyst. Synergetic effect of efficient NiO as active metal and medium basic sites from AS enhanced DRM catalytic activity and stability with low coke formation.
The world water resources are contaminated due to discharge of a large number of pollutants from industrial and domestic sources. A variety of a single and multiple units of physical, chemical, and biological processes are employed for pollutants removal from wastewater. Adsorption is the most widely utilized process due to high efficiency, simple procedure and cost effectiveness. This paper reviews the research work carried out on the use of geopolymer materials for the adsorption of heavy metals and dyes. Geopolymers possess good surface properties, heterogeneous microstructure and amorphous structure. The performance of geopolymers in the removal of heavy metals and dyes is reported comparable to other materials. The pseudo-second order kinetics and Langmuir isotherm models mostly fit to the adsorption data suggesting homogeneous distribution of adsorption sites with the formation of monolayer adsorbate on the surface of geopolymers. Adsorption of heavy metals and dyes onto geopolymers is spontaneous, endothermic and entropy driven process. Future research should focus on the enhancement of geopolymer performance, testing on pollutants other than heavy metals and dyes, and verification on real wastewater in continuous operation.