Energy is widely used in industry for heating and cooling, with natural gas (NG) being the largest primary energy source in Malaysia, closely followed by coal. Renewable energy, such as biogas upgrading to biomethane, could cut the use of fossil fuels by supplementing NG usage due to their similar physicochemical and thermochemical characteristics. Biogas production plants in Malaysia are more commonly seen in waste-to-energy scenarios, with the technology anaerobic digestion, and their deployment is supported via feed-in tariffs (FiT) for power generation. Other potential applications such as the conversion of biogas into biomethane, injection into the natural gas grid or transportation through a virtual pipeline may still need further technical development. This paper presents spatial techno economic optimisation modelling using BeWhere to determine decentralised biomethane production plants using feedstock from multiple sources of biogas, including palm oil mill effluent (POME), food waste, cattle manure and chicken manure. This model considered potential configurations and sizes of the biomethane plants, the transportation of biomethane using a virtual pipeline (at 250 psig) and demand in one of the states in Malaysia, namely Johor. It was found that two to four biomethane plants with capacities ranging between 125 and 700 m3/h were located in densely populated areas or heavier industrial consumers when the carbon tax was implemented at 167.71 EUR/tCO2 (800 MYR/tCO2). Sensitivity analysis suggested that biomethane production increases with the increasing country renewable energy share target to beyond 2080 MW. It is recommended that specific policy regulations and Feed-in Tariff (FiT) mechanisms are used to expand the biomethane market share in the country.
This study reports the biodiversity of thermophilic cellulolytic bacterial strains that present in the north Malaysian mangrove ecosystem. Soil samples were collected at the four most northern state of Malaysia (Perak, Pulau Pinang, Kedah and Perlis). The samples obtained were first enriched in nutrient broth at 45°C and 55°C prior culturing in the carboxymethylcellulose (CMC) agar medium. Repeated streaking was performed on the CMC agar to obtain a pure culture of each isolate prior subjecting it to hydrolysis capacity testing. The isolates that showing the cellulolytic zone (halozone) were sent for 16S rRNA sequencing. Total seven isolates (two from Perak, three from Kedah, another two were from Perlis and Penang each) showed halozone. The isolate (KFX-40) from Kedah exhibited highest halozone of 3.42 ± 0.58, meanwhile, the one obtained from Perak (AFZ-0) showed the lowest hydrolysis capacity (2.61 ± 0.10). Based on 16S rRNA sequencing results, 5 isolates (AFY-40, AFZ-0, KFX-40, RFY-20, and PFX-40) were determined to be Anoxybacillus sp. The other two isolates were identified as Bacillus subtilis (KFY-40) and Paenibacillus dendritiformis (KFX-0). Based on growth curve, doubling time of Anoxybacillus sp. UniMAP-KB06 was calculated to be 32.3 min. Optimal cellulose hydrolysis temperature and pH of this strain were determined to be 55°C and 6.0 respectively. Addition of Mg2+ and Ca2+ were found to enhance the cellulase activity while Fe3+ acted as an enzyme inhibitor.
In view of the simple and rapid conveniency of magnetic separation, magnetic nanocomposites had notably gained attention from researchers for environmental field applications. In this work, carboxylated magnetic multi-walled carbon nanotubes (c-MMWCNTs) and novel sulfonated MMWCNTs (s-MMWCNTs) were synthesized by a facile solvent-free direct doping method. Fourier transform infrared spectroscopy, X-ray diffraction, scanning electron microscope, energy dispersive X-ray, vibrating sample magnetometer, and point of zero charge analyses confirmed the successful doping of the Fe3O4 nanoparticles into the functionalized MWCNTs to form MMWCNTs. Besides, the bonding stabilities of both c-MMWCNTs and s-MMWCNTs were compared, and results showed that s-MMWCNTs possessed more substantial bonding stability than that of c-MMWCNTs with significantly less leaching amount of Fe3O4. The adsorption capacity of s-MMWCNTs was higher than that of c-MMWCNTs owing to the stronger electronegativity sulfonic group in s-MMWCNTs. Moreover, the reusability experiments proved that the adsorbent remained consistently excellent MB removal efficiency (R > 94%) even reused for twelve cycles of batch adsorption. The finding of the present work highlights the simple fabrication of novel s-MMWCNTs and its potential to be served as a promising and sustainable adsorbent for water remediation owing to its enhanced bonding stability, high adsorption performance, magnetic separability, and supreme recyclability.