The CO2 absorption rate by using a Monoethanolamide (MEA) solution through the spiral wired channel in concentric circular membrane contactors under both concurrent-flow and countercurrent-flow operations was investigated experimentally and theoretically. The one-dimensional mathematical modeling equation developed for predicting the absorption rate and concentration distributions was solved numerically using the fourth Runge-Kutta method under various absorbent flow rate, CO2 feed flow rate and inlet CO2 concentration in the gas feed. An economical viewpoint of the spiral wired module was examined by assessing both absorption flux improvement and power consumption increment. Meanwhile, the correlated average Sherwood number to predict the mass-transfer coefficient of the CO2 absorption mechanisms in a concentric circular membrane contactor with the spiral wired annulus channel is also obtained in a generalized and simplified expression. The theoretical predictions of absorption flux improvement were validated by experimental results in good agreements. The amine solution flowing through the annulus of a concentric circular tube, which was inserted in a tight-fitting spiral wire in a small annular spacing, could enhance the CO2 absorption flux improvement due to reduction of the concentration polarization effect. A larger concentration polarization coefficient (CPC) was achieved in the countercurrent-flow operations than that in concurrent-flow operations for various operations conditions and spiral-wire pitches. The absorption flux improvement for inserting spiral wire in the concentric circular module could provide the maximum relative increment up to 46.45%.
In the species groups related to Diphasiastrum multispicatum and D. veitchii, hybridization was investigated in samples from northern and southern Vietnam and the island of Taiwan, including available herbarium specimens from southeast Asia. The accessions were analyzed using flow cytometry (living material only), Sanger sequencing and multiplexed inter-simple sequence repeat genotyping by sequencing. We detected two cases of ancient hybridization involving different combinations of parental species; both led via subsequent duplication to tetraploid taxa. A cross D. multispicatum × D. veitchii from Malaysia represents D. wightianum, a tetraploid taxon according to reported DNA content measurements of dried material (genome formulas MM, VV and MMVV, respectively). The second case involves D. veitchii and an unknown diploid parent (genome formula XX). Three hybridogenous taxa (genome formulas VVX, VVXX, VVVX) were discernable by a combination of flow cytometry and molecular data. Taxon I (VVX, three clones found on Taiwan island) is apparently triploid. Taxon II represents another genetically diverse and sexual tetraploid species (VVXX) and can be assigned to D. yueshanense, described from Taiwan island but occurring as well in mainland China and Vietnam. Taxon III is as well most likely tetraploid (VVVX) and represented by at least one, more likely two, clones from Taiwan island. Taxa I and III are presumably asexual and new to science. Two independently inherited nuclear markers recombine only within, not between these hybrids, pointing towards reproductive isolation. We present an evolutionary scheme which explains the origin of the hybrids and the evolution of new and fully sexual species by hybridization and subsequent allopolyploidization in flat-branched clubmosses.
Two geometric shape turbulence promoters (circular and square of same areas) of different array patterns using three-dimensional (3D) printing technology were designed for direct contact membrane distillation (DCMD) modules in the present study. The DCMD device was performed at middle temperature operation (about 45 °C to 60 °C) of hot inlet saline water associated with a constant temperature of inlet cold stream. Attempts to reduce the disadvantageous temperature polarization effect were made inserting the 3D turbulence promoters to promote both the mass and heat transfer characteristics in improving pure water productivity. The additive manufacturing 3D turbulence promoters acting as eddy promoters could not only strengthen the membrane stability by preventing vibration but also enhance the permeate flux with lessening temperature polarization effect. Therefore, the 3D turbulence promoters were individually inserted into the flow channel of the DCMD device to create vortices in the flow stream and increase turbulent intensity. The modeling equations for predicting the permeate flux in DCMD modules by inserting the manufacturing 3D turbulence promoter were investigated theoretically and experimentally. The effects of the operating conditions under various geometric shapes and array patterns of turbulence promoters on the permeate flux with hot inlet saline temperatures and flow rates as parameters were studied. The distributions of the fluid velocities were examined using computational fluid dynamics (CFD). Experimental study has demonstrated a great potential to significantly accomplish permeate flux enhancement in such new design of the DCMD system. The permeate flux enhancement for the DCMD module by inserting 3D turbulence promoters in the flow channel could provide a maximum relative increment of up to 61.7% as compared to that in the empty channel device. The temperature polarization coefficient (τtemp) was found in this study for various geometric shapes and flow patterns. A larger τtemp value (the less thermal resistance) was achieved in the countercurrent-flow operation than that in the concurrent-flow operation. An optimal design of the module with inserting turbulence promoters was also delineated when considering both permeate flux enhancement and energy utilization effectiveness.