Displaying publications 141 - 160 of 1007 in total

Abstract:
Sort:
  1. Preparation of palm oil methyl esters for alkenyl succinic anhydride production
    Nur Azreena Idris, Loh SK, Choo YM, Boey PL
    Sains Malaysiana, 2010;39.
    The fractions of fatty acid methyl esters (FAME) i.e. crude palm oil methyl esters (CPOME), RBD palm olein methyl esters (RBD Palm Olein ME) and used frying oil methyl esters (UFOME) rich in unsaturated fatty esters were used to prepare alkenyl succinic anhydrides (ASA). The fractions were obtained via fractional distillation that separated the unsaturated fatty esters from the saturated fatty esters. The fractions with the highest content of unsaturated fatty esters were reacted with maleic anhydride (MA) for 8 hours at 240oC with the MA/FAME ratio of 1.5. The reaction was conducted without catalyst and solvent. The crude alkenyl succinic anhydride (ASA) obtained was purified by column chromatography. The purified compound was characterised by FTIR.
    Matched MeSH terms: Spectroscopy, Fourier Transform Infrared
  2. Mechanical and thermal properties of palm-based polyurethane composites filled with Fe3O4, PANI and PANI/Fe3O4
    Liow CH, Sahrim Ahmad, Khairiah Badri
    Sains Malaysiana, 2011;40.
    In-situ polymerization method was used to prepare palm-based polyurethane (PU) composites loading with 15 wt% magnetite (Fe3O4), polyaniline (PANI) and Fe3O4 coated with PANI labeled as PU15, PP and PPM, respectively. FTIR spectroscopy analysis indicated a shift in the carbonyl, C=O and NH in PP. The shift of the peak indicated that there was hydrogen bonding between the C=O (proton acceptor) of urethane with NH (proton-donator) of PANI. PPM gave the highest impact and flexural strengths at 4875 kJ/ m2 and 42 MPa, respectively but with the lowest flexural modulus (1050 MPa). Two-stage degradation behavior was observed in the TGA thermogram.
    Matched MeSH terms: Spectroscopy, Fourier Transform Infrared
  3. Effects of Rf power on structural properties of Nc-Si:h thin films deposited by layer-by-layer (LBL) deposition technique
    Goh BT, Muhamad Rasat Muhamad, Saadah Abdul Rahman
    Sains Malaysiana, 2012;41:993-1000.
    The effects of rf power on the structural properties of hydrogenated nanocrystalline silicon (nc-Si:H) thin films deposited using layer-by-layer (LbL) deposition technique in a home-built plasma enhanced chemical vapor deposition (PECVD) system were investigated. The properties of the films were characterized by X-ray diffraction (XRD), microRaman scattering spectroscopy, high resolution transmission electron microscope (HRTEM) and Fourier transform infrared (FTIR) spectroscopy. The results showed that the films consisted of different size of Si crystallites embedded within an amorphous matrix and the growth of these crystallites was suppressed at higher rf powers. The crystalline volume fraction of the films was optimum at the rf power of 60 W and contained both small and big crystallites
    with diameters of 3.7 nm and 120 nm, respectively. The hydrogen content increased with increasing rf power and enhanced the structural disorder of the amorphous matrix thus decreasing the crystalline volume fraction of the films. Correlation of crystalline volume fraction, hydrogen content and structure disorder of the films under the effect of rf
    power is discussed.
    Matched MeSH terms: Spectroscopy, Fourier Transform Infrared
  4. Structural and luminescence properties of Fe3+ doped antimony lead borophosphate glass
    Leong PM, Eeu TY, Leow TQ, Pang XG, Zuhairi Ibrahim, Rosli Hussin
    Sains Malaysiana, 2014;43:915-922.
    Structural and luminescence properties of borophosphate glasses with different modifier doped with transition metal ions have been investigated in this study. The glass sample from the series of xPb 30 4:0 .2Sb20 3:0.3B 20 3:(0 .5-x)P 20 5 and ySb 20 3:0 .2Pb 30 4:(0 .5-y)B 20 3:0 .3P 20 5where x 20 mol% and 0 y 0 .1 5mol% , respectively, were doped with 0.01 mol% of Fe 20 3 system have been prepared using the melt-quenching technique. The structural properties of samples had been studied using fourier transform infrared (FT-m) spectroscopy. The FT-IR study showed the network structure of the studied glasses based on the B 20 3-P 20 5host with the 5b203 and Pb203 modifiers. The results of FT-IR showed traces of B03 and B04 with the introduction of 5b203 and Pb203 modifiers. With the increasing content of B203 which replacing content of P205 in the glass network, the intensity of the borate band decreases and shifted to lower frequency. uv-Vis spectroscopy analysed the transition of Fe3+ from ground state to excited state in the ultraviolet spectral region. The photoluminescence of samples were studied using photoluminescence spectroscopy. The result of photoluminescence spectroscopy showed the effect of photoluminescence enhancement by doping Fe3+ as activator.
    Matched MeSH terms: Spectroscopy, Fourier Transform Infrared
  5. Optimization of microencapsulation process for self-healing polymeric material
    Then S, Gan SN, Noor Hayaty Abu Kasim
    Sains Malaysiana, 2011;40:1179-1186.
    A series of poly(urea-formaldehyde) (PUF) microcapsules filled with dicyclopentadiene (DCPD) was successfully prepared by in situ polymerization. The effect of diverse process parameters and ingredients on the morphology of the microcapsules was observed by SEM, optical microscopy (OM) and digital microscopy. Different techniques for the characterization of the chemical structure and the core content were considered such as FT-IR and 1H-NMR as well as the characterization of thermal properties by DSC. High yields of free flowing powder of spherical microcapsules were produced. The synthesized microcapsules can be incorporated into another polymeric host material. In the event the host material cracks due to excessive stress or strong impact, the microcapsules would rupture to release the DCPD, which could polymerize to repair the crack.
    Matched MeSH terms: Spectroscopy, Fourier Transform Infrared
  6. Characterization of residue from EFB and kenaf core fibres in the liquefaction process
    Sarani Zakaria, Rasidi Roslan, Umar Adli Amran, Chia CH, Saiful Bahari Bakaruddin
    Sains Malaysiana, 2014;43:429-435.
    Different type of fibers which is EFB and KC were liquefied in phenol with the presence of sulphuric acid as a catalyst. The liquefied residue was characterized by using Fourier transform infrared (FTIR) to determine the functional groups presents in both residues, X-ray diffraction (XRD) to determine the degree of crystallinity in the residue, thermogravimetric analysis (TGA) to analyze the thermal properties of the residue and scanning electron microscope (SEM) to investigate the structure and morphology of the residue. Phenol-to-EFB/KC ratio shows great effect on the amount of residue in the liquefaction process. Peak appearance can be observed in the FTIR analysis at 810 and 750 cm-1 which is attributed to the para and meta benzene, respectively or to be specific its associated to the p-alkyl phenol and m-alkyl phenol. In the XRD analysis, CrI of lignocellulosic materials increased after liquefaction process. Liquefaction process caused chemical penetration across the grain of the fiber, thus the fiber bundles started to separate into individual fibers shown in the SEM micrograph and the weights lost curve for both liquefied EFB and KC experienced three region decompositions.
    Matched MeSH terms: Spectroscopy, Fourier Transform Infrared
  7. Fulltext Characterization data of titanate compounds synthesized using hydrothermal method at various temperature
    Razali MH, Ismail NA, Osman UM, Rozaini MZH, Yusoff M
    Data Brief, 2020 Feb;28:104992.
    PMID: 31890823 DOI: 10.1016/j.dib.2019.104992
    Titanate compounds was synthesized using hydrothermal method at various temperature (100, 150, 200, and 250 °C) for 24 hours. As-synthesized titanate was characterized using FTIR, XRD and nitrogen gas adsorption. FTIR spectra was scanned from 4000 to 400 cm-1 using Perkin Elmer Spectrum 100 FTIR spectrophotometer. XRD diffractogram was performed by using Rigaku Miniflex (II) X-ray diffractometer operating at a scanning rate of 2.00° min-1. The diffraction spectra were recorded at the diffraction angle, 2θ from 10° to 80° at room temperature. Nitrogen gas adsorption analysis was studied by using Micromeritics ASAP2020 (Alaska) to determine the surface area and pores size distribution. The nitrogen adsorption and desorption was measured at 77 K (temperature of liquid nitrogen) and the samples were degassed in a vacuum at 110 °C under nitrogen flow for overnight prior to analysis.
    Matched MeSH terms: Spectroscopy, Fourier Transform Infrared
  8. Predictive modelling of colossal ATR-FTIR spectral data using PLS-DA: empirical differences between PLS1-DA and PLS2-DA algorithms
    Lee LC, Jemain AA
    Analyst, 2019 Apr 08;144(8):2670-2678.
    PMID: 30849143 DOI: 10.1039/c8an02074d
    In response to our review paper [L. C. Lee et al., Analyst, 2018, 143, 3526-3539], we present a study that compares empirical differences between PLS1-DA and PLS2-DA algorithms in modelling a colossal ATR-FTIR spectral dataset. Over the past two decades, partial least squares-discriminant analysis (PLS-DA) has gained wide acceptance and huge popularity in the field of applied research, partly due to its dimensionality reduction capability and ability to handle multicollinear and correlated variables. To solve a K-class problem (K > 2) using PLS-DA and high-dimensional data like infrared spectra, one can construct either K one-versus-all PLS1-DA models or only one PLS2-DA model. The aim of this work is to explore empirical differences between the two PLS-DA algorithms in modeling a colossal ATR-FTIR spectral dataset. The practical task is to build a prediction model using the imbalanced, high dimensional, colossal and multi-class ATR-FTIR spectra of blue gel pen inks. Four different sub-datasets were prepared from the principal dataset by considering the raw and asymmetric least squares (AsLS) preprocessed forms: (a) Raw-global region; (b) Raw-local region; (c) AsLS-global region; and (d) AsLS-local region. A series of 50 models which includes the first 50 PLS components incrementally was constructed repeatedly using the four sub-datasets. Each model was evaluated using six different variants of v-fold cross validation, autoprediction and external testing methods. As a result, each PLS-DA algorithm was represented by a number of figures of merit. The differences between PLS1-DA and PLS2-DA algorithms were assessed using hypothesis tests with respect to model accuracy, stability and fitting. On the other hand, confusion matrices of the two PLS-DA algorithms were inspected carefully for assessment of model parsimony. Overall, both the algorithms presented satisfactory model accuracy and stability. Nonetheless, PLS1-DA models showed significantly higher accuracy rates than PLS2-DA models, whereas PLS2-DA models seem to be much more stable compared to PLS1-DA models. Eventually, PLS2-DA also proved to be less prone to overfitting and is more parsimonious than PLS1-DA. In conclusion, the relatively high accuracy of the PLS1-DA algorithm is achieved at the cost of rather low parsimony and stability, and with an increased risk of overfitting.
    Matched MeSH terms: Spectroscopy, Fourier Transform Infrared
  9. Rapid assessment of total MCPD esters in palm-based cooking oil using ATR-FTIR application and chemometric analysis
    Goh KM, Maulidiani M, Rudiyanto R, Wong YH, Ang MY, Yew WM, et al.
    Talanta, 2019 Jun 01;198:215-223.
    PMID: 30876552 DOI: 10.1016/j.talanta.2019.01.111
    The technique of Fourier transform infrared spectroscopy is widely used to generate spectral data for use in the detection of food contaminants. Monochloropropanediol (MCPD) is a refining process-induced contaminant that is found in palm-based fats and oils. In this study, a chemometric approach was used to evaluate the relationship between the FTIR spectra and the total MCPD content of a palm-based cooking oil. A total of 156 samples were used to develop partial least squares regression (PLSR), artificial neural network (nnet), average artificial neural network (avNNET), random forest (RF) and cubist models. In addition, a consensus approach was used to generate fusion result consisted from all the model mentioned above. All the models were evaluated based on validation performed using training and testing datasets. In addition, the box plot of coefficient of determination (R2), root mean square error (RMSE), slopes and intercepts by 100 times randomization was also compared. Evaluation of performance based on the testing R2 and RMSE suggested that the cubist model predicted total MCPD content with the highest accuracy, followed by the RF, avNNET, nnet and PLSR models. The overfitting tendency was assessed based on differences in R2 and RMSE in the training and testing calibrations. The observations showed that the cubist and avNNET models possessed a certain degree of overfitting. However, the accuracy of these models in predicting the total MCPD content was high. Results of the consensus model showed that it slightly improved the accuracy of prediction as well as significantly reduced its uncertainty. The important variables derived from the cubist and RF models suggested that the wavenumbers corresponding to the MCPDs originated from the -CH=CH2 or CH=CH (990-900 cm-1) and C-Cl stretch (800-700 cm-1) regions of the FTIR spectrum data. In short, chemometrics in combination with FTIR analysis especially for the consensus model represent a potential and flexible technique for estimating the total MCPD content of refined vegetable oils.
    Matched MeSH terms: Spectroscopy, Fourier Transform Infrared
  10. Low pressure DC-Plasma system for the modification of Polymeric Membrane surfaces
    Chalad Yuenyao, Thawat Chittrakarn, Yutthana Tirawanichakul, Hideki Nakajima
    Sains Malaysiana, 2017;46:783-793.
    The main objectives of this work were to develop a lab-scale direct current (DC) glow discharges plasma system for modification of organic and inorganic membranes. Characteristics of plasma system were presented under the discharge of five gases (Ar, N2, air, O2, and CO2). A Langmuir double probe was used for the evaluation of the electron temperature (Te) and electron density (ne) of plasmas. The current and voltage (I-V) characteristic curves were analyzed. Relationships between breakdown voltage (VB) of gases and products of gas pressure and inter-electrode gap (pd) were studied in form of Paschen curves. The results showed that Te of plasma in various gases was in the range of 4-13 eV, while the ne varied between 108 and 109 cm-3. The plasma generated at different gas pressure and applied voltage is in the normal and abnormal modes. Finally, the constructed DC-plasma system was utilized for modification of polymeric membrane surfaces. Treatment time, discharge power and type of gas were varied. The tailoring of membrane surfaces was analyzed through the water contact angle and percent-weight loss (PWL) measurements, DMTA, AFM, XPS and FTIR spectrum. It could be shown that DC-plasma from this system can be used to modify the surface of polymeric membranes.
    Matched MeSH terms: Spectroscopy, Fourier Transform Infrared
  11. Fecl3-activated carbon developed from coconut leaves: characterization and application for methylene blue removal
    Ali H. Jawad, Mohd Azlan Bin Mohd Ishak, Nur Nasulhah Kasim, Ramlah Abd Rashid
    Sains Malaysiana, 2018;47:603-610.
    In this study, coconut leaves were used as a starting material for the production of activated carbon by thermal
    carbonization using FeCl3
    -activation method. The characterization of coconut leaves-FeCl3
    activated carbon (FAC) were
    evaluated by bulk density, ash content, moisture content, point-of-zero charge (pHpzc) analysis, iodine test, scanning
    electron microscopy (SEM), Fourier transform infrared (FTIR) and elemental (CHNS-O) analysis. The effect of the adsorbent
    dosage (0.02-0.25 g), initial pH (3-11), initial dye concentrations (30-350 mg/L) and contact time (1-180 min) on the
    adsorption of the methylene blue (MB) at 303 K was performed via batch experiments. The Pseudo-Second Order (PSO)
    describes the kinetic model well whereas the Langmuir isotherm proved that adsorption behavior at equilibrium with
    maximum adsorption capacity (qmax) of 66.00 mg/g.
    Matched MeSH terms: Spectroscopy, Fourier Transform Infrared
  12. Fulltext Lightweight and Durable PVDF-SSPF Composites for Photovoltaics Backsheet Applications: Thermal, Optical and Technical Properties
    Alaaeddin MH, Sapuan SM, Zuhri MYM, Zainudin ES, M Al-Oqla F
    Materials (Basel), 2019 Jun 29;12(13).
    PMID: 31261926 DOI: 10.3390/ma12132104
    Photovoltaic module backsheets are characterized according to their thermal, optical, mechanical, and technical properties. This work introduces new fabricated backsheets for PV modules using polyvinylidene fluoride (PVDF) reinforced with short sugar palm fiber (SSPF) composites. The preparation of composites undergoes multiple phases of fabrication. Thermal, optical, and technical investigations of their properties were conducted. Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, in-situ scanning probe microscopy (SPM), dynamic mechanical analysis (DMA), thermal mechanical analysis (TMA), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and prolonged technical testing were accomplished to expansively understand the complex behavior of composites under various conditions. The optical properties of PV backsheets are critical components in determining the reflectance, absorbance, and transmittance of light. The PVDF-SSPF composites exhibited exceptional compatibility and thermal stability, further revealing a homogenous composite structure with enhanced interfacial bonding between the short fiber and polymer matrix.
    Matched MeSH terms: Spectroscopy, Fourier Transform Infrared
  13. Fulltext Preparation and physicochemical characterization of fish skin gelatine hydrolysate from shortfin scad (Decapterus macrosoma)
    Rasli, H.I., Sarbon, N.M.
    International Food Research Journal, 2019;26(1):287-294.
    MyJurnal
    Enzymatic hydrolysis of proteins is an important bioprocess method to prepare bioactive peptides with many functionality and health benefits. The aims of the present work were to prepare and determine the physicochemical characteristics of gelatine hydrolysate from skin of shortfin scad (SSGH) via hydrolysis using alcalase. Analyses on chemical composition, molecular weight by SDS PAGE, protein concentration, amino acid composition, Fourier Transform Infrared Spectroscopic features, and solubility of SSGH were thus performed. The yield of SSGH obtained was 51.01% (d.b.). The chemical compositions of SSGH for moisture, protein, fat, and ash were 13.82%, 90.05%, 1.95%, and 12.48%, respectively. SSGH showed low molecular weight (
    Matched MeSH terms: Spectroscopy, Fourier Transform Infrared
  14. Fulltext Hybrid Polymerisation: An Exploratory Study of the Chemo-Mechanical and Rheological Properties of Hybrid-Modified Bitumen
    Joohari IB, Giustozzi F
    Polymers (Basel), 2020 Apr 18;12(4).
    PMID: 32325743 DOI: 10.3390/polym12040945
    In this study, the mechanical and rheological properties of hybrid polymer-modified bitumen (PMB) have been investigated. For this purpose, nine different polymers-including crumb rubber, elastomers and plastomers at varying content-were studied to evaluate their mechanical performance as single polymers, first, and as a combination of two or more polymers as a hybrid polymer blend. Subsequently, the hybrid polymer blends were added in a relatively small percentage into the base bitumen to study its influence on the rheological performance of hybrid PMB. The mechanical properties identified from the analysis of the stress-strain curve of the single polymers were the Young's Modulus, tensile stress, and elongation at break. The chemical structure of the polymer hybrid blends was analysed using FTIR, followed by frequency sweep tests conducted using the dynamic shear rheometer (DSR) to determine the bitumen rheological properties. Results showed that hybrid PMB enhances the viscoelastic behaviour of bitumen at both low and high temperature compared to other PMBs only including single polymers.
    Matched MeSH terms: Spectroscopy, Fourier Transform Infrared
  15. Fulltext Physical, mechanical, chemical and biological properties data of gellan gum incorporating titanium dioxide nanoparticles biofilm
    Razali MH, Ismail NA, Amin KAM
    Data Brief, 2020 Jun;30:105478.
    PMID: 32346560 DOI: 10.1016/j.dib.2020.105478
    Gellan gum incorporating titanium dioxide nanoparticles biofilm was synthesized and characterized using UV, FTIR and XRD to study their physical and chemical properties. The mechanical properties were measured using universal mechanical testing. Meanwhile, the biological properties were investigated towards for antibacterial and cell proliferation. This comprehensive data are relevant with the research article entitled "Gellan gum incorporating titanium dioxide nanoparticles biofilm as wound dressing: Physicochemical, mechanical, antibacterial properties and wound healing studies" [1].
    Matched MeSH terms: Spectroscopy, Fourier Transform Infrared
  16. Fulltext Characterization and Performance Evaluation of Cellulose Acetate-Polyurethane Film for Lead II Ion Removal
    Iqhrammullah M, Marlina M, Khalil HPSA, Kurniawan KH, Suyanto H, Hedwig R, et al.
    Polymers (Basel), 2020 Jun 09;12(6).
    PMID: 32526903 DOI: 10.3390/polym12061317
    Global pollution from toxic metal waste has resulted in increased research on toxic metal adsorption. A cellulose acetate-polyurethane (CA-PU) film adsorbent was successfully prepared in this research. The cellulose acetate-polyurethane film adsorbent was prepared with a polycondensation reaction between cellulose acetate and methylene diphenyl diisocyanate. The CA-PU bond formation was confirmed by functional group analysis obtained from Fourier transform infrared (FTIR) spectroscopy. The obtained film was characterized for improved tensile and thermal properties with the addition of methylene diphenyl diisocyanate (MDI). The adsorption ability of the obtained film was evaluated with laser-induced breakdown spectroscopy (LIBS). The best film adsorbent from the LIBS was selected and studied for adsorption isotherm. The FTIR analysis confirmed the formation of the CA-PU bond from the polycondensation between cellulose acetate and the methylene diphenyl diisocyanate. The result showed that the addition of methylene diphenyl diisocyanate (MDI) resulted in the urethane network's growth. The characterization result showed an improvement in the morphology, thermal stability, and tensile strength of the film. The LIBS studies showed improvement in the adsorption of Pb2+ with CA-PU compared with the neat CA. The isotherm studies revealed that Pb2+ adsorption by cellulose acetate-polyurethane film adsorbent was heterogeneously dependent on the Freundlich isotherm model (R2 = 0.97044). Overall, the polycondensation method proposed by this study enhanced the Pb2+ removal, and was comparable to those reported in previous studies.
    Matched MeSH terms: Spectroscopy, Fourier Transform Infrared
  17. Flotation separation of poly (ethylene terephthalate and vinyl chloride) mixtures based on clean corona modification: Optimization using response surface methodology
    Zhao Y, Han F, Guo L, Zhang J, Zhang H, Abdelaziz IIM, et al.
    Waste Manag, 2021 Dec;136:184-194.
    PMID: 34689097 DOI: 10.1016/j.wasman.2021.10.018
    Postconsumer polyethylene terephthalate (PET) has potential applications in many areas of manufacturing, but contamination by hazardous polyvinyl chloride (PVC) in common waste streams can reduce its recyclable value. Separating collected PET-PVC mixtures before recycling remains very challenging because of the similar physicochemical properties of PET and PVC. Herein, we describe a novel flotation process with corona modification pretreatment to facilitate the separation of PET-PVC mixtures. Through water contact angle, surface free energy, X-ray photoelectron and FT-IR characterization, we found that polar hydroxyl groups can be more easily introduced on the PVC surface than on the PET surface induced by corona modification. This selective wetting can suppress the floatability of PVC, leading to the separation of PET as floating product. A reliable mechanism including two different hydrogen-abstraction pathways was established. Response surface methodology consisting of Plackett-Burman and Box-Behnken designs was adopted for optimization of the combined process, and control parameters were solved based on high-quality prediction models, with fitting from significant variables and interactions. For physical or chemical circulation strategies with PET purity prioritization, the validated purity of the product reached 96.05% at a 626 W corona power, 5.42 m/min passing speed, 24.78 mg/L frother concentration and 286 L/h air flow rate. For the energy recuperation strategy with PET recovery prioritization, the factual recovery reached 98.08% under a 601 W corona power, 6.04 m/min passing speed, 27.55 mg/L frother concentration and 184 L/h air flow rate. The current work provides technological insights into the cleaner disposal of waste plastics.
    Matched MeSH terms: Spectroscopy, Fourier Transform Infrared
  18. Fulltext Chlorambucil-Iron Oxide Nanoparticles as a Drug Delivery System for Leukemia Cancer Cells
    Hussein-Al-Ali SH, Hussein MZ, Bullo S, Arulselvan P
    Int J Nanomedicine, 2021;16:6205-6216.
    PMID: 34526768 DOI: 10.2147/IJN.S312752
    Introduction: Traditional cancer therapies may have incomplete eradication of cancer or destroy the normal cells. Nanotechnology solves the demerit by a guide in surgical resection of tumors, targeted chemotherapies, selective to cancerous cells, etc. This new technology can reduce the risk to the patient and automatically increased the probability of survival. Toward this goal, novel iron oxide nanoparticles (IONPs) coupled with leukemia anti-cancer drug were prepared and assessed.

    Methods: The IONPs were prepared by the co-precipitation method using Fe+3/Fe+2ratio of 2:1. These IONPs were used as a carrier for chlorambucil (Chloramb), where the IONPs serve as the cores and chitosan (CS) as a polymeric shell to form Chloramb-CS-IONPs. The products were characterized using transmission electron microscopy (TEM), powder X-ray diffraction (PXRD), scanning electron microscopy (SEM) analysis, Fourier transform infrared spectroscopy (FTIR), vibrating sample magnetometry (VSM) analyses, and thermal gravimetric analysis (TGA).

    Results: The as-prepared IONPs were found to be magnetite (Fe3O4) and were coated by the CS polymer/Chloramb drug for the formation of the Chloramb-CS-IONPs. The average size for CS-IONPs and Chloramb-CS-IONPs nanocomposite was found to be 15 nm, with a drug loading of 19% for the letter. The release of the drug from the nanocomposite was found to be of a controlled-release manner with around 89.9% of the drug was released within about 5000 min and governed by the pseudo-second order. The in vitro cytotoxicity studies of CS-IONPs and Chloramb-CS-IONPs nanocomposite were tested on the normal fibroblast cell lines (3T3) and leukemia cancer cell lines (WEHI). Chloramb in Chloramb-CS-IONPs nanocomposite was found to be more efficient compared to its free form.

    Conclusion: This work shows that Chloramb-CS-IONPs nanocomposite is a promising candidate for magnetically targeted drug delivery for leukemia anti-cancer agents.

    Matched MeSH terms: Spectroscopy, Fourier Transform Infrared
  19. Fulltext Statistical Optimization for Acid Hydrolysis of Microcrystalline Cellulose and Its Physiochemical Characterization by Using Metal Ion Catalyst
    Karim MZ, Chowdhury ZZ, Hamid SBA, Ali ME
    Materials (Basel), 2014 Oct 13;7(10):6982-6999.
    PMID: 28788226 DOI: 10.3390/ma7106982
    Hydrolyzing the amorphous region while keeping the crystalline region unaltered is the key technology for producing nanocellulose. This study investigated if the dissolution properties of the amorphous region of microcrystalline cellulose can be enhanced in the presence of Fe(3+) salt in acidic medium. The process parameters, including temperature, time and the concentration of metal chloride catalyst (FeCl₃), were optimized by using the response surface methodology (RSM). The experimental observation demonstrated that temperature and time play vital roles in hydrolyzing the amorphous sections of cellulose. This would yield hydrocellulose with higher crystallinity. The factors that were varied for the production of hydrocellulose were the temperature (x₁), time (x₂) and FeCl₃ catalyst concentration (x₃). Responses were measured in terms of percentage of crystallinity (y₁) and the yield (y₂) of the prepared hydrocellulose. Relevant mathematical models were developed. Analysis of variance (ANOVA) was carried out to obtain the most significant factors influencing the responses of the percentage of crystallinity and yield. Under optimum conditions, the percentage of crystallinity and yield were 83.46% and 86.98% respectively, at 90.95 °C, 6 h, with a catalyst concentration of 1 M. The physiochemical characteristics of the prepared hydrocellulose were determined in terms of XRD, SEM, TGA and FTIR analyses. The addition of FeCl₃ salt in acid hydrolyzing medium is a novel technique for substantially increasing crystallinity with a significant morphological change.
    Matched MeSH terms: Spectroscopy, Fourier Transform Infrared
  20. Fulltext Evaluation of Biological Pretreatment of Rubberwood with White Rot Fungi for Enzymatic Hydrolysis
    Nazarpour F, Abdullah DK, Abdullah N, Zamiri R
    Materials (Basel), 2013 May 15;6(5):2059-2073.
    PMID: 28809260 DOI: 10.3390/ma6052059
    e effects of biological pretreatment on the rubberwood (Hevea brasiliensis), was evaluated after cultivation of white rot fungi Ceriporiopsis subvermispora, Trametes versicolor, and a mixed culture of C. subvermispora and T. versicolor. The analysis of chemical compositions indicated that C. subvermispora had greater selectivity for lignin degradation with the highest lignin and hemicellulose loss at 45.06% and 42.08%, respectively, and lowest cellulose loss (9.50%) after 90 days among the tested samples. X-ray analysis showed that pretreated samples had a higher crystallinity than untreated samples. The sample pretreated by C. subvermispora presented the highest crystallinity of all the samples which might be caused by the selective degradation of amorphous components. Fourier transform infrared (FT-IR) spectroscopy demonstrated that the content of lignin and hemicellulose decreased during the biological pretreatment process. A study on hydrolysis of rubberwood treated with C. subvermispora, T. versicolor, and mixed culture for 90 days resulted in an increased sugar yield of about 27.67%, 16.23%, and 14.20%, respectively, as compared with untreated rubberwood (2.88%). The results obtained demonstrate that rubberwood is a potential raw material for industrial applications and white rot fungus C. subevermispora provides an effective method for improving the enzymatic hydrolysis of rubberwood.
    Matched MeSH terms: Spectroscopy, Fourier Transform Infrared
Related Terms
Filters
Contact Us

Please provide feedback to Administrator ([email protected])

External Links