Kraft lignin (KL) is a renewable source of many valuable intermediate biochemical products currently derived from petroleum. An excessive of lignin comes from pulping wastewater caused an adverse pollution problems hence affecting human and aquatic life. A comprehensive study pertaining to emulsion liquid membrane (ELM) extraction of lignin from pulping wastewater was presented. ELM formulation contains Aliquat 336 as carrier, kerosene as diluent, sodium bicarbonate (NaHCO3 ) as stripping agent and Span 80 as surfactant. The emulsion stability was investigated at different surfactant concentrations, homogenizer speed and emulsification time. Modifier (2-ethyl-1-hexanol) was added to avoid segregation of third phase while improving the emulsion stability. At optimum conditions, 95% and 56% of lignin were extracted and recovered, respectively at 10 min of extraction time, 0.007 M of Aliquat 336, 0.1 M of NaHCO3 and 1:5 of treat ratio. Additional of modifier was contributed to highest recovery up to 98%. The ELM process was found to be equally feasible and quite effective in the recovery of KL from real pulping wastewater. Therefore, ELM process provides a promising alternative technology to recover KL from pulping wastewater while solving the environmental problems simultaneously.
The discharge of improperly treated oil/water emulsion by industries imposes detrimental effects on human health and the environment. The membrane process is a promising technology for oil/water emulsion treatment. However, it faces the challenge of being maintaining due to membrane fouling. It occurs as a result of the strong interaction between the hydrophobic oil droplets and the hydrophobic membrane surface. This issue has attracted research interest in developing the membrane material that possesses high hydraulic and fouling resistance performances. This research explores the vapor-induced phase separation (VIPS) method for the fabrication of a hydrophilic polysulfone (PSF) membrane with the presence of polyethylene glycol (PEG) as the additive for the treatment of oil/water emulsion. Results show that the slow nonsolvent intake in VIPS greatly influences the resulting membrane structure that allows the higher retention of the additive within the membrane matrix. By extending the exposure time of the cast film under humid air, both surface chemistry and morphology of the resulting membrane can be enhanced. By extending the exposure time from 0 to 60 s, the water contact angle decreases from 70.28 ± 0.61° to 57.72 ± 0.61°, and the clean water permeability increases from 328.70 ± 8.27 to 501.89 ± 8.92 (L·m-2·h-1·bar-1). Moreover, the oil rejection also improves from 85.06 ± 1.6 to 98.48 ± 1.2%. The membrane structure was transformed from a porous top layer with a finger-like macrovoid sub-structure to a relatively thick top layer with a sponge-like macrovoid-free sub-structure. Overall results demonstrate the potential of the VIPS process to enhance both surface chemistry and morphology of the PSF membrane.
The objective of this study is to investigate the intermolecular interactions between the surfactants and the fractions of heavy crude oils. Two possible interactions were considered; polar and ionic interactions for two heavy crude oil-surfactant systems, and 20 surfactant-steam flooding tests were conducted on these crudes by testing nine surfactants (three anionic, three cationic, and three nonionic) with different tail lengths and charged head groups. The performance differences observed in each core flood were discussed through the additional analyses. To explain polar interactions, the pseudo blends of crude oil fractions (fractionation of saturates, aromatics, resins, and asphaltenes) were exposed to the surfactant solutions under vapor and liquid water conditions and their mutual interactions were visualized under an optical microscope. To explain ionic interactions, the charges on asphaltene surfaces were analyzed by zeta potential measurements before and after core flood tests on both the produced and the residual oil asphaltenes. The addition of surfactants improved the oil recovery when compared to steam injection alone. However, different oil recoveries were obtained with different surfactants. Further analyses showed that asphaltenes are key and the interaction of asphaltenes with other crude oil fractions or surfactants determines the success of surfactant-steam processes. The polar interactions favor the emulsion formation more; hence, if the polar interactions are more dominant than the ion interactions in the overall crude oil-surfactant system, the surfactant flooding process into heavy oil reservoir became more successful.
In this study, glucose is used as a template to manufacture microporosity in silica. Based on this objective, five different molar ratios of glucose (0%, 10%, 20%, 30% and 50%) were used for this experiment to maximise its affinity to adsorb oil droplets. The sample has been characterized using
thermogravimetric analysis (TGA), Nitrogen Adsorption and UltravioletVisible (UV-Vis) pectroscopy. The adsorption of oil was tested in 1000 ppm oil-water emulsion in order to determine the performance of the templated silica. TGA analysis showed that 550 ̊C is a suitable temperature for material calcination for all the samples. N2 adsorption showed the glucose templated silica (50%) had limited porosity, with a low surface area of 2 m2 /g. This is much lower than non-templated silica which was mesoporous, with an average pore diameter of 2.6 nm and a surface area of 272 m2 /g. Interestingly, despite the low porosity of the templated silica, high oil-water
separations were achieved. This shows that glucose-templated silica is a promising material for oil-water separations.
While the economy is rapidly expanding in most emerging countries, issues coupled with a higher population has created foreseeable tension among food, water, and energy. It is crucial for more sustainable valorization of resources, for instance, nanocellulose, to address the core challenges in environmental sustainability. As the complexity of the system evolved, the timescale of project development has increased exponentially. However, research on the design and operation of integrated nanomaterials, along with energy supply, monitoring, and control infrastructure, has seriously lagged. The development cost of new materials can be significantly reduced by utilizing molecular simulation technology in the design of nanostructured materials. To realize its potential, nanocellulose, an amphiphilic biopolymer with the presence of rich -OH and -CH structural groups, was investigated via molecular dynamics simulation to reveal its full potential as Pickering emulsion stabilizer at the molecular level. This work has successfully quantified the Pickering stabilization mechanism profiles by nanocellulose, and the phenomenon could be visualized in three stages, namely the initial homogenous phase, rapid formation of micelles and coalescence, and lastly the thermodynamic equilibrium of the system. It was also observed that the high bead order was always coupled with a high volume of phase separation activities, through a coarse-grained model within 20,000 time steps. The outcome of this work would be helpful to provide an important perspective for the future design and development of nanocellulose-based emulsion products, which cater for food, cosmeceutical, and pharmaceutical industries.
A novel method for the assay of polyhydroxyalkanoate (PHA)-degrading ability of triacylglycerol lipases was developed. By applying the natural affinity of lipases towards hydrophobic interfaces, a sensitive and rapid densitometry analysis for the evaluation of hydrolytic activity of lipase droplets towards PHA-coated surface was successfully carried out. We found that 12 out of 14 tested lipases which are of fungal, bacterial and animal origin were able to hydrolyze P(3HB-co-92 mol% 4HB) thin film. The patterns and opacity of the hydrolysis spots of lipases on PHA films allowed easy comparison of PHA-hydrolytic strength of lipases. Lipase from the bacterium Chromobacterium viscosum exhibited the highest PHA-degrading activity. The hydrolytic activity of lipases on water insoluble PHA, emulsified p-nitrophenyl laurate and olive oil were also compared and interestingly some lipases showed better activity when PHA was used as a substrate.
The application of protein-protein interaction (PPI) has been widely used in various industries, such as food, nutraceutical, and pharmaceutical. A deeper understanding of PPI is needed, and the molecular forces governing proteins and their interaction must be explained. The design of new structures with improved functional properties, e.g., solubility, emulsion, and gelation, has been fueled by the development of structural and colloidal building blocks. In this review, the molecular forces of protein structures are discussed, followed by the relationship between molecular force and structure, ways of a bind of proteins together in solution or at the interface, and functional properties. A more detailed look is thus taken at the relationship between the various influencing factors on molecular forces involved in PPI. These factors include protein properties, such as types, concentration, and mixing ratio, and solvent conditions, such as ionic strength and pH. This review also summarizes methods tha1t are capable of identifying molecular forces in protein and PPI, as well as characterizing protein structure.
Encapsulating fish oil by spray drying with an adequate wall material was investigated to determine if stable powders containing emulsified fish-oil-droplets can be formed. In particular, the dextrose equivalent (DE) of maltodextrin (MD) affects the powder structure, surface-oil ratio, and oxidative stability of fish oil. The carrier solution was prepared using MD with different DEs (DE = 11, 19, and 25) and sodium caseinate as the wall material and the emulsifier, respectively. The percentage of microcapsules having a vacuole was 73, 39, and 38% for MD with DE = 11, 19, and 25, respectively. Peroxide values (PVs) were measured for the microcapsules incubated at 60 °C. The microcapsules prepared with MD of DE = 25 and 19 had lower PVs than those prepared with MD of DE = 11. The difference in PV can be ascribed to the difference in the surface-oil ratio of the spray-dried microcapsules.
Kenaf seed oil-in-water nanoemulsions (KSON) and kenaf seed oil-in-water macroemulsions were produced to access their gastroprotective effect against indomethacin- and ethanol-induced ulcers in comparison with non-emulsified kenaf seed oil (KSO). Emulsifier mixture (EM) that used to emulsify KSO was also included in the study. Ulcer index, stomach tissue oxidative status, and histopathological changes in indomethacin-induced and ethanol-induced ulcer models were both evaluated. KSON had demonstrated good gastroprotective effect against both ulcer models than non-emulsified KSO and KSOM. In addition, the gastroprotective effect of KSON was comparable to the standard drug, Omeprazole. EM also exhibited gastroprotective effect, especially in indomethacin-induced ulcers. This may be attributed to its high antioxidant activity and cytoprotective effect of sodium caseinate contained in the EM. Results supported that KSON enhanced the bioavailability of native KSO; therefore it offers gastroprotective effect for the prevention of gastric ulceration as a natural alternative to the synthetic drug.
Chitin biopolymer has received significant attention recently by many industries as a green technology. Nanotechnology has been used to make chitin nanocrystals (ChiNCs) that are rod-shaped natural nanomaterials with nanoscale size. Owing to the unique features such as biodegradability, biocompatibility, renewability, rod-shape, and excellent surface and interfacial, physiochemical, and thermo-mechanical properties; ChiNCs have been green and attractive products with wide applications specifically in medical and pharmaceutical, food and packaging, cosmetic, electrical, and electronic, and also in the oil and gas industry. This review aims to give a comprehensive and applied insight into ChiNCs technology. It starts with reviewing different sources of chitin and their extraction methods followed by the characterization of ChiNCs. Furthermore, a detailed investigation into various complex fluids (dispersions, emulsions, foams, and gels) stabilized by ChiNCs and their characterisation have been thoroughly deliberated. Finally, the current status including ground-breaking applications, untapped investigations, and future prospective have been presented.
Pharmaceutical delivery systems are developed to improve the physicochemical properties of therapeutic compounds. Emulsions are one of these drug delivering systems formulated using water, oils and lipids as main ingredients. Extensive data are usually generated on the physical and chemical characteristics of these oil-in-water and lipid emulsions. However, the oxidative tendency of emulsions is often overlooked. Oxidation impacts the overall quality and safety of these pharmaceutical emulsions. Additionally, introducing oxidatively unstable emulsions into biological systems further promotes oxidation in situ. Products of these reactions then continue to pose serious harm to cells and fuel other physiological oxidation reactions. Consequently, the increase of oxidation products leads to oxidative damage to biological systems. Thus, emulsions with lower lipid peroxidation are more stable and will reduce the negative effects of oxidation in situ. Preventive measures during the formulation of emulsions are important. Many naturally occurring and cost effective substances possess low oxidation tendencies and confer oxidative protection when used in emulsions. Additionally, certain preparatory methods should be employed to reduce or better control lipid peroxidation. Finally, emulsions must be evaluated for their oxidation susceptibility using the various techniques available. Careful attention to the preparation of emulsions and assessment of their oxidative stability will help produce safer emulsions without compromising efficacy.
This study was set up to model and optimize the performance and emission characteristics of a diesel engine fueled with carbon nanoparticle-dosed water/diesel emulsion fuel using a combination of soft computing techniques. Adaptive neuro-fuzzy inference system tuned by particle swarm algorithm was used for modeling the performance and emission parameters of the engine, while optimization of the engine operating parameters and the fuel composition was conducted via multiple-objective particle swarm algorithm. The model input variables were: injection timing (35-41° CA BTDC), engine load (0-100%), nanoparticle dosage (0-150 μM), and water content (0-3 wt%). The model output variables included: brake specific fuel consumption, brake thermal efficiency, as well as carbon monoxide, carbon dioxide, nitrogen oxides, and unburned hydrocarbons emission concentrations. The training and testing of the modeling system were performed on the basis of 60 data patterns obtained from the experimental trials. The effects of input variables on the performance and emission characteristics of the engine were thoroughly analyzed and comprehensively discussed as well. According to the experimental results, injection timing and engine load could significantly affect all the investigated performance and emission parameters. Water and nanoparticle addition to diesel could markedly affect some performance and emission parameters. The modeling system could predict the output parameters with an R2 > 0.93, MSE
The purpose of this study was to investigate the preparation of formulated water- in-soybean oil-in-water emulsions by repeated premix membrane emulsification method using a cellulose acetate membrane. The effect of selective membrane emulsification process parameters (concentration of the emulsifiers, number of passes of the emulsions through the membrane and storage temperature) on the properties and stability of the developed emulsions were also investigated. 1, 3, 6, 8-pyrenetetrasulfonic acid tetrasodium salt (PTSA) was used as a hydrophilic model ingredient for the encapsulation of bioactive substances. W/O emulsions with 7 wt% (weight percentage) PGPR displays homogeneous and very fine dispersions, with the median diameter at 0.640 μm. Meanwhile, emulsions prepared by membrane emulsification (fine W/O/W) showed the highest stability at Tween 80 concentrations of 0.5 wt.% (weight percentage). It concluded that at 7 wt.% (weight percentage) PGPR concentration and 0.5 wt.% (weight percentage) Tween 80 concentrations, the most uniform particles with minimum mean size of oil drops (9.926 μm) were obtained after four passes through the membrane. Thus, cellulose acetate membrane can be used for preparing a stable W/O/W emulsions by repeated premix ME due to low cost and relatively easy to handle.
Surimi refers to concentrated myofibrial protein extracted from fish flesh by washing process. Surimi powder, is normally prepared in a dried form, and potentially useful as a raw material for preparation of seafood products. Surimi powder offers many advantages in industrial application, such as easy handling, low distribution cost, and physically convenient for addition to dry mixtures. In order to prevent the denaturation of the protein during drying, dryoprotectants such as sucrose and polyols can be added. Surimi powder is classified as fish protein concentrate type A because its protein content is higher than 65%. Surimi powder has good functional properties, such as gelation, water holding capacity, and emulsifying and foaming properties. Gel-based fish products and fish snacks are common products that can be made from surimi powder.
This study reported the extraction optimization and characterization of cobia (Rachycentron canadum) skin gelatin. Optimization study was carried out to determine the effect of CH3COOH concentration, skin to water ratio, extraction temperature and extraction time on gelatin yield (GY) and gel strength (GS) using Response Surface Methodology (RSM). The optimum conditions were 0.15mol/L for CH3COOH concentration, 82.4oC of extraction temperature, 6 h of extraction time and 1:6 of skin to water ratio, which produced cobia gelatin with GY of 20.10% and GS of 205.6 g. Characteristics of cobia skin gelatin (CG) were then compared to that of commercial bovine gelatin (BG). It was found that the most dominant amino acid in CG was glycine, proline and alanine. There was no difference in foaming and emulsifying properties of CG and BG at 1% concentration, but at 2% and 3% concentration, BG performed better. CG was found to have higher fat binding capacity but lower water holding capacity than BG. Least gelling concentration for CG was recorded at 2% while for BG at 1%. CG and BG had a pI at pH 6.05 and 4.82, respectively. This study shows that cobia skin gelatin has potential as halal alternative to bovine gelatin in food industry.
This study examines and compares the influence of pH on the functional, rheological and structural properties of eel skin (Monopterus sp.) and bovine gelatins. Functional properties studied and compared were emulsifying capacity and stability; water holding capacity; fat binding capacity; foaming capacity; and foaming stability. The rheological properties studied include gel strength and dynamic oscillatory measurements. The structural properties of eel skin and bovine gelatin were determined by Fourier transform infrared spectroscopy (FTIR). Results obtained showed that eel skin gelatin treated at pH 8 (compared to pH 5) exhibited the higher emulsifying, fat binding, foaming and viscoelasticity properties. The FTIR spectrum assay showed that eel skin gelatin presented a similar structure to that of bovine gelatin. This study demonstrated that pH levels influence functional, rheological and structural properties of eel skin gelatin and that these properties were enhanced to either equal or surpass those of bovine gelatin. Hence, this study indicates that eel skin gelatin has immense potential for use as an alternative to bovine gelatin.
Covalently cross-linked nanogels were prepared via irradiation of inverse micelles that had been preparedfrom radiation crosslinkable polymer, water, oil and surfactant. A mixture of polymer, water, heptane andsodium dioctyl sulfosuccinate (AOT) at certain compositions forms inverse micelles with the size rangingfrom 2 to 8 nm. The hydrophilic head of the surfactant facilitates encapsulation of water soluble polymer.If the entrapped polymer is radiation crosslinkable, it is expected that upon irradiation, polymerizationshall take place in such small and confined space, leading to formation of nano-sized polymeric gel.Meanwhile, emulsion at 2 nm size was chosen for gamma irradiation process. The formation of thenano-sized discreet gel using irradiation of inverse micelles technique was proven at a dose as low as 5kGy to obtain nanogel sized ~ 95 nm.
The use of microemulsion in the development of nanoparticle based on acrylated palm oil product is demonstrated. Acr ylated palm oil microemulsions were prepared using ionic surfactant. Combination methods of emulsion polymerization and radiation crosslinking were applied to the microemulsion system for synthesizing nanoparticle. The ionizing radiat ion technique was introduced to generate a crosslinking reaction in the development of nanoparticle. The nanoparticle was evaluated in terms of particle diameter, surface charge, pH and conductance. Their image was captured using Tra nsmission electron microscopy (TEM). Results show that the size, charge and shape of the particles are influenced by c oncentration of surfactants, monomer concentration, radiation dose and time of storage. The study showed a promising method to produced nanoparticle. This nano-sized product has the potential to be utilized as controlled-drug-release-carrier.
In this study, Hydrolysate from angelwing clam (Pholas orientalis) was produced at 0, 1, 2 and 3 hrs and E/S ratio of 0.5 and 3% using alcalase where the pH and temperature were kept constant at pH 8.5 and 60°C, respectively. The hydrolysates were analysed for antioxidant and functional properties such as solubility, emulsifying properties and water and oil holding capacity. Degree of hydrolysis (DH), yield, functional and antioxidant properties were influenced by the hydrolysis time and E/S ratio. Higher enzyme concentration (E/S 3%) and longer hydrolysis time increased the DH. Yield was higher at E/S 3% but reduced with hydrolysis time. Longer hydrolysis time produced more soluble hydrolysate and higher metal chelating activity but lower in emulsifying properties and DPPH activity. Higher enzyme concentration resulted in increase only in solubility and metal chelating activity. This study revealed that enzymatic hydrolysis using alcalase should be performed at shorter hydrolysis time using intermediate concentration of enzyme (E/S between 0.5 to 3%) in order to produce angelwing clam hydrolysate with collectively good functional and antioxidant properties
Despite its attractive features for energy saving separation, the performance of forward osmosis (FO) has been restricted by internal concentration polarization and fast fouling propensity that occur in the membrane sublayer. These problems have significantly affected the membrane performance when treating highly contaminated oily wastewater. In this study, a novel double-skinned FO membrane with excellent anti-fouling properties has been developed for emulsified oil-water treatment. The double-skinned FO membrane comprises a fully porous sublayer sandwiched between a highly dense polyamide (PA) layer for salt rejection and a fairly loose dense bottom zwitterionic layer for emulsified oil particle removal. The top dense PA layer was synthesized via interfacial polymerization meanwhile the bottom layer was made up of a zwitterionic polyelectrolyte brush - (poly(3-(N-2-methacryloxyethyl-N,N-dimethyl) ammonatopropanesultone), abbreviated as PMAPS layer. The resultant double-skinned membrane exhibited a high water flux of 13.7 ± 0.3 L/m2.h and reverse salt transport of 1.6 ± 0.2 g/m2.h under FO mode using 2 M NaCl as the draw solution and emulsified oily solution as the feed. The double-skinned membrane outperforms the single-skinned membrane with much lower fouling propensity for emulsified oil-water separation.