Displaying publications 81 - 100 of 120 in total

Abstract:
Sort:
  1. Continuous biosynthesis of biodiesel from waste cooking palm oil in a packed bed reactor: optimization using response surface methodology (RSM) and mass transfer studies
    Halim SF, Kamaruddin AH, Fernando WJ
    Bioresour Technol, 2009 Jan;100(2):710-6.
    PMID: 18819793 DOI: 10.1016/j.biortech.2008.07.031
    This study aimed to develop an optimal continuous procedure of lipase-catalyzes transesterification of waste cooking palm oil in a packed bed reactor to investigate the possibility of large scale production further. Response surface methodology (RSM) based on central composite rotatable design (CCRD) was used to optimize the two important reaction variables packed bed height (cm) and substrate flow rate(ml/min) for the transesterification of waste cooking palm oil in a continuous packed bed reactor. The optimum condition for the transesterification of waste cooking palm oil was as follows: 10.53 cm packed bed height and 0.57 ml/min substrate flow rate. The optimum predicted fatty acid methyl ester (FAME) yield was 80.3% and the actual value was 79%. The above results shows that the RSM study based on CCRD is adaptable for FAME yield studied for the current transesterification system. The effect of mass transfer in the packed bed reactor has also been studied. Models for FAME yield have been developed for cases of reaction control and mass transfer control. The results showed very good agreement compatibility between mass transfer model and the experimental results obtained from immobilized lipase packed bed reactor operation, showing that in this case the FAME yield was mass transfer controlled.
    Matched MeSH terms: Quality Control
  2. Quality assessment of palm products upon prolonged heat treatment
    Tarmizi AH, Lin SW
    J Oleo Sci, 2008;57(12):639-48.
    PMID: 19001776
    Extending the frying-life of oils is of commercial and economic importance. Due to this fact, assessment on the thermal stability of frying oils could provide considerable savings to the food processors. In this study, the physico-chemical properties of five palm products mainly palm oil, single-fractionated palm olein, double-fractionated palm olein, red palm olein and palm-based shortening during 80 hours of heating at 180 degrees C were investigated. Heating properties of these products were then compared with that of high oleic sunflower oil, which was used as reference oil. The indices applied in evaluating the quality changes of oils were free fatty acid, smoke point, p-anisidine value, tocols, polar and polymer compounds. Three palm products i.e. palm oil, single-fractionated palm olein and double-fractionated palm olein were identified to be the most stable in terms of lower formation of free fatty acid, polar and polymer compounds as well as preserving higher smoke point and tocols content compared to the other three oils. The low intensity of hydrolytic and oxidative changes due to prolonged heating, suggests that these palm products are inherently suitable for frying purposes.
    Matched MeSH terms: Quality Control
  3. Gaining competitive advantage in personal dosimetry services through ISO 9001 certification
    Noriah MA
    Radiat Prot Dosimetry, 2007;125(1-4):101-4.
    PMID: 17145724
    This paper discusses the advantage of certification process in the quality assurance of individual dose monitoring in Malaysia. The demand by customers and the regulatory authority for a higher degree of quality service requires a switch in emphasis from a technically focused quality assurance program to a comprehensive quality management for service provision. Achieving the ISO 9001:2000 certification by an accredited third party demonstrates acceptable recognition and documents the fact that the methods used are capable of generating results that satisfy the performance criteria of the certification program. It also offers a proof of the commitment to quality and, as a benchmark, allows measurement of the progress for continual improvement of service performance.
    Matched MeSH terms: Quality Control
  4. Quality evaluation analysis of bioengineered human skin
    Mazlyzam AL, Aminuddin BS, Lokman BS, Isa MR, Fuzina H, Fauziah O, et al.
    Med J Malaysia, 2004 May;59 Suppl B:39-40.
    PMID: 15468808
    Our objective is to determine the quality of tissue engineered human skin via immunostaining, RT-PCR and electron microscopy (SEM and TEM). Culture-expanded human keratinocytes and fibroblasts were used to construct bilayer tissue-engineered skin. The in vitro skin construct was cultured for 5 days and implanted on the dorsum of athymic mice for 30 days. Immunostaining of the in vivo skin construct appeared positive for monoclonal mouse anti-human cytokeratin, anti-human involucrin and anti-human collagen type I. RT-PCR analysis revealed loss of the expression for keratin type 1, 10 and 5 and re-expression of keratin type 14, the marker for basal keratinocytes cells in normal skin. SEM showed fibroblasts proliferating in the 5 days in vitro skin. TEM of the in vivo skin construct showed an active fibrocyte cell secreting dense collagen fibrils. We have successfully constructed bilayer tissue engineered human skin that has similar features to normal human skin.
    Matched MeSH terms: Quality Control
  5. Determination of lead in Smilax myosotiflora herbal preparations obtained in Malaysia
    Ang HH, Lee KL, Kiyoshi M
    Int J Environ Health Res, 2004 Aug;14(4):261-72.
    PMID: 15369991
    The DCA (Drug Control Authority), Malaysia implemented the phase 3 registration of traditional medicines on 1 January 1992 with special emphasis on the quality, efficacy and safety (including the presence of heavy metals) in all pharmaceutical dosage forms of traditional medicinal preparations. As such, a total of 100 traditional medicinal preparations, containing Smilax myosotiflora, in various pharmaceutical dosage forms, which were bought in the Malaysian market, were analysed for lead content using atomic absorption spectrophotometry. Results showed that 15% of the products analysed possessed 10.23-23.05 ppm of lead, and therefore, do not comply with the quality requirement for traditional medicines in Malaysia. The quality requirement for traditional medicines in Malaysia is that they should not exceed 10 ppm of lead. Out of these 15 products, five products exhibited 10.23-23.05 ppm of lead, in fact they have already been registered with the DCA Malaysia. However, the rest of the products, which possessed 12.24-20.72 ppm of lead, have still not been registered with the DCA Malaysia. Although this study successfully showed that only 85% of the products complied with the quality requirement for traditional medicines in Malaysia pertaining to lead, they cannot, however, be assumed to be safe from lead contamination because of batch-to-batch inconsistency.
    Matched MeSH terms: Quality Control
  6. Heavy metals in spices and herbs from wholesale markets in Malaysia
    Nordin N, Selamat J
    Food Addit Contam Part B Surveill, 2013;6(1):36-41.
    PMID: 24786623 DOI: 10.1080/19393210.2012.721140
    As, Cd, Pb and Hg were analysed in commonly consumed spices and herbs in Malaysia. The range of As, Cd, Pb and Hg content was 0.24-2.54, 0.23-8.07, 1.54-8.94 and 0.06-0.52 µg g(-1), respectively. The highest concentration of Cd, Pb and Hg in spices and herbs exceeded the maximum permitted proportion, which are 1, 2 and 0.05 µg g(-1), respectively. This study suggests further monitoring of Cd, Pb and Hg on daily consumption of spices and herbs and its toxicological implication for consumers since only the amount of As was lower than the permitted concentration.
    Matched MeSH terms: Quality Control
  7. Recognition of higher medical institutions in Russia
    Severyanova L, Lazarev A
    Med J Malaysia, 2005 Aug;60 Suppl D:71-4.
    PMID: 16315629
    The Russian Federation of higher medical institutions get State accreditation, if their activity conforms to criteria determined by the Ministry of Public Health and the Ministry of Education of the Russian Federation. Kursk State Medical University (KSMU) has a confirmed to requirement of accreditation by the Russian Federation, to conduct annually training of about 5000 students at 12 faculties. KSMU carries out pre-medical undergraduate and postgraduate training in the specialty "Doctor of medicine". For the first time in Russia KSMU was allowed to conduct a 6-year medical training with the use of English as an intermediary language by the Ministry of Public Health and the Ministry of Education. In this relation programmes of training teachers for conducting instruction with the use of an intermediary language (English) and training students Russian with the level necessary for free communication with Russian patients and staff of the clinics have been developed and realized.
    Matched MeSH terms: Quality Control
  8. Medical education today: globalising with quality
    Shahabudin SH
    Med J Malaysia, 2005 Aug;60 Suppl D:4-10.
    PMID: 16315616
    With globalization education has become a tradable service governed by the rules and regulations of GATS and worth trillions of dollars. International standards are rapidly being developed to facilitate cross border supply of services. In medical education, the WFME has produced International Guidelines on Quality in Medical Education which has a regional equivalent in the WHO Western Pacific Region, and the IIME has defined the minimum essential requirements of standards in medical education in seven core competences. Malaysia, having an explicit policy of making education a sector for revenue generation, has put in place regulatory frameworks and incentives to make the country a centre of educational excellence. Within the ambit of this national aspiration, medical education has grown phenomenally in the last decade. Standards and procedures for accreditation of medical schools in line with the world standards have been developed and implemented and policies are enforced to facilitate compliance to the standards. The ultimate goal is for medical schools to be self-accredited. In striving towards self-accreditation medical schools should be innovative in making changes in the three requirements of medical education. These are the intellectual and social imperatives and strategies for effective implementation.
    Matched MeSH terms: Quality Control
  9. Fulltext Effect of DNase treatment on RNA extraction from preimplantation murine embryos
    Norhazlin J, Nor-Ashikin MN, Hoh BP, Sheikh Abdul Kadir SH, Norita S, Mohd-Fazirul M, et al.
    Genet. Mol. Res., 2015;14(3):10172-84.
    PMID: 26345954 DOI: 10.4238/2015.August.28.1
    The quality of RNA is crucial when performing microarray experiments. This is particularly important when dealing with preimplantation embryos, from which a minimum yield of RNA of good quality can be produced. We report the optimization of several RNA extraction methods applied to preimplantation embryos at different stages of development. The quality of the samples was confirmed using a microarray and reverse transcription quantitative real-time polymerase chain reaction (RT-qPCR) analysis. A total of 30 cultured two-cell stage embryos of ICR mice were pooled at the 8-cell, morula, and blastocyst stages. The embryos were divided into two groups comprising DNase-treated and non-DNase-treated RNA samples. Total RNA was extracted using a Pico Pure RNA Isolation Kit following the manufacturer protocol, with some modifications. Lysed samples were bound to a silica-based filter, treated with deoxyribonuclease I (DNase I), and washed several times before elution. RNA concentration and integrity were evaluated using an Agilent 2100 Bioanalyzer and an RNA 6000 Pico Assay kit. Although concentrations of non-DNase-treated RNAs were higher than DNase-treated RNA, DNase-treated RNA gave a higher RNA integrity number compared with non-DNase-treated RNA. Inclusion of DNase treatment in the RNA extraction procedure gave the best quality RNA samples from preimplantation embryos, as validated by microarray and RT-qPCR quality control.
    Matched MeSH terms: Quality Control
  10. A potential resource for bioconversion of domestic wastewater sludge
    Molla AH, Fakhru'l-Razi A, Abd-Aziz S, Hanafi MM, Roychoudhury PK, Alam MZ
    Bioresour Technol, 2002 Dec;85(3):263-72.
    PMID: 12365494
    Twenty seven filamentous fungal strains representing five genera; Aspergillus, Penicillium, Trichoderma, Myriodontium and Pleurotus were isolated from four sources; domestic wastewater sludge cake (SC) from IWK (Indah Water Konsortium) wastewater treatment plant, palm oil mill effluent compost from Sri Ulu palm Oil Processing Mill, compost of plant debris, and fungal fruiting bodies from a rotten wood stump. Thirty-three strains/isolates were tested for their ability to convert domestic wastewater sludge into compost by assessing biomass production and growth rate on sludge enriched media. The strains/isolates Aspergillus niger, SS-T2008, WW-P1003 and RW-P1 512 produced the highest dry biomass at higher sludge supplemented culture media from their respective group (Aspergillus, Trichoderma, Penicillium and Basidiomycetes, respectively). This implied these strains are better adapted for growth at higher sludge rich substances, and subsequently may be efficient in bioconversion/biodegradation of sludge. The fungi isolated from ecological closely related sources were more amendable to adaptation in a sludge rich culture media.
    Matched MeSH terms: Quality Control
  11. Treatment of phenolic wastewater using agricultural wastes as an adsorbent in a sequencing batch reactor
    Lee KM, Lim PE
    Water Sci Technol, 2003;47(10):41-7.
    PMID: 12862215
    The objective of this study is to investigate the potential of the activated rice husk to be used as an alternative adsorbent to powdered activated carbon (PAC) in the simultaneous adsorption and biodegradation processes under sequencing batch reactor (SBR) operation to treat synthetic wastewater containing phenol, p-methylphenol, p-ethylphenol and p-isopropylphenol. The rice husk (PRH) was activated by pyrolysis at 600 degrees C for 5 hours in a nitrogen atmosphere. Using the Langmuir model, the limiting adsorption capacities of PRH for the phenols were found to vary from 0.015-0.05 of those of PAC. The SBR reactors with and without adsorbent addition were operated with fill, react, settle, draw and idle periods in the ratio of 4:6:1:0.76:0.25 for a cycle time of 12 hours. For phenolic wastewater containing, 1,200 mg/L phenol, 1,200 mg/L p-methylphenol, 800 mg/L p-ethylphenol and 660 mg/L p-isopropylphenol, it was found that the biodegradation process alone was unable to produce effluent of quality which would satisfy the discharge standards of COD < or = 100 mg/L and phenol concentration < or = 1 mg/L. The addition of PAC in the ratio of PAC/phenolic compound at 0.095 g/g for phenol, 0.119 g/g for p-methylpheol, 0.179 g/g for p-ethylphenol and 0.220 g/g for p-isopropylphenol, can improve the effluent quality to satisfy the discharge standards. Equivalent treatment performance was achieved with the use of PRH at dosages of 2-3 times higher than those of PAC for all the phenolic wastewater studied. The increased adsorption capacity of PRH shown in the treatment indicates bioregeneration of the adsorbed surface during the treatment process.
    Matched MeSH terms: Quality Control
  12. Seeking representation in policy-making governmental bodies
    Abu Bakar S
    Malays J Pathol, 1997 Dec;19(2):93-7.
    PMID: 10879247
    Matched MeSH terms: Quality Control
  13. Wavelet-based compression of medical images: filter-bank selection and evaluation
    Saffor A, bin Ramli AR, Ng KH
    Australas Phys Eng Sci Med, 2003 Jun;26(2):39-44.
    PMID: 12956184
    Wavelet-based image coding algorithms (lossy and lossless) use a fixed perfect reconstruction filter-bank built into the algorithm for coding and decoding of images. However, no systematic study has been performed to evaluate the coding performance of wavelet filters on medical images. We evaluated the best types of filters suitable for medical images in providing low bit rate and low computational complexity. In this study a variety of wavelet filters are used to compress and decompress computed tomography (CT) brain and abdomen images. We applied two-dimensional wavelet decomposition, quantization and reconstruction using several families of filter banks to a set of CT images. Discreet Wavelet Transform (DWT), which provides efficient framework of multi-resolution frequency was used. Compression was accomplished by applying threshold values to the wavelet coefficients. The statistical indices such as mean square error (MSE), maximum absolute error (MAE) and peak signal-to-noise ratio (PSNR) were used to quantify the effect of wavelet compression of selected images. The code was written using the wavelet and image processing toolbox of the MATLAB (version 6.1). This results show that no specific wavelet filter performs uniformly better than others except for the case of Daubechies and bi-orthogonal filters which are the best among all. MAE values achieved by these filters were 5 x 10(-14) to 12 x 10(-14) for both CT brain and abdomen images at different decomposition levels. This indicated that using these filters a very small error (approximately 7 x 10(-14)) can be achieved between original and the filtered image. The PSNR values obtained were higher for the brain than the abdomen images. For both the lossy and lossless compression, the 'most appropriate' wavelet filter should be chosen adaptively depending on the statistical properties of the image being coded to achieve higher compression ratio.
    Matched MeSH terms: Quality Control
  14. Determination of absorbed dose for photon and electron beams from a linear accelerator by comparing various protocols on different phantoms
    Banjade DP, Tajuddin AA, Shukri A
    Appl Radiat Isot, 2001 Aug;55(2):235-43.
    PMID: 11393765
    Protocols developed for high-energy dosimetry IAEA (Technical Reports Series No. 277, 1997), AAPM (Med. Phys. 10 (1983) 741: Med. Phys. 18 (1991) 73: Med. Phys. 21 (1994) 1251), IPEMB (Phys. Med. Biol. 41 (1996) 2557), and HPA (Phys. Med. Biol. 28 (1983) 1097) have continued to enhance precision in dose measurements and the optimization of radiotherapy procedures. While recent dosimetry protocols, including those due to the IAEA and IPEMB, have made a number of improvements compared with previous protocols, it is further desirable to develop absolute dosimetry methods of dose measurements. Measurements based on careful implementation of procedures contained within the various protocols have been carried out in an effort to determine the extent to which discrepancies exist among the protocols. Dose in water at dmax was measured using cylindrical and parallel-plate ionization chambers for 6 MV photon beams and 5 and 12 MeV electron beams. Results obtained from the use of the AAPM and HPA protocols for 6 MV photon beams were found to be 0.9% larger and 0.1% smaller, respectively, than those measured following the IAEA protocol. Calibration dose measurements for 5 and 12 MeV electron beams in water phantoms were found to agree to within 1%, this being well within recommendations from the ICRU and other sources regarding the accuracy of dose delivery.
    Matched MeSH terms: Quality Control
  15. The specific absorbed dose constant: comparison of values published for 60Co photons
    Samat SB, Evans CJ
    Radiat Prot Dosimetry, 2003;103(4):341-7.
    PMID: 12797557
    For the specific absorbed dose constant for 60Co photons, three values quoted directly in the literature and two derived indirectly from published information are reported. The three publications giving the direct values mentioned no medium of absorption, whereas the other two specify tissue. A database of the specific absorbed dose constant is generated for each of 14 media namely air, water, bone and 11 types of soft tissue. These values are consistent with the three directly quoted values plus one of the indirectly obtained values. Air is found to be unlikely as the medium for the first three; and appropriate media for these are suggested. For the other two values, the generated database suggests that one is too small to be accurate; while the other is correct for tissue (as stated in the publication). An apparent error of 10(3) is identified in one of the values directly quoted.
    Matched MeSH terms: Quality Control
  16. Liquid chromatographic detection of Dowtherm A contamination in oleochemicals and edible oils
    Moh FM, Tang TS
    J AOAC Int, 1999 8 13;82(4):893-6.
    PMID: 10444829
    A rapid and direct liquid chromatographic (LC) technique is described for the determination of a eutectic mixture of diphenyl oxide and biphenyl such as Dowtherm A thermal heating fluid (THF) in oleochemicals and palm olein. Analysis is performed with an RP-18 column with fluorescence detection (excitation at 247 nm and emission at 310 nm). The isocratic mobile phase (1.0 mL/min) consists of methanol and water (90 + 10, v/v). A linear calibration model (correlation coefficient = 0.9999) was developed directly from used Dowtherm A THF with the biphenyl peak (4.70 min) as a marker. Average recoveries from spiked glycerin, fatty alcohol mixture, methyl ester mixture, fatty acids, and palm olein were 90.9-108.7%, with a detection limit of 0.1 microgram/mL. The technique requires no prior sample cleanup nor extraction steps and is good for quality assurance purposes.
    Matched MeSH terms: Quality Control
  17. Toxicity of phenol on Macrobrachium rosenbergii (de Man) eggs, larvae, and post-larvae
    Law AT, Yeo ME
    Bull Environ Contam Toxicol, 1997 Mar;58(3):469-74.
    PMID: 9008059
    Matched MeSH terms: Quality Control
  18. Optimization of nuclear medicine procedures for the diagnosis and management of thyroid disorders: report of a research coordination meeting held in Vienna, 15-17 December 1986 under the auspices of the International Atomic Energy Agency
    Ganatra R, Gembicki M, Nofal M
    Nucl Med Commun, 1988 Feb;9(2):131-9.
    PMID: 3386976
    The third and final meeting of a coordinated research programme on the diagnosis and management of thyroid disorders was held in Vienna from 15 to 17 December 1986. The participants were from Czechoslovakia, Egypt, Israel, Malaysia and Thailand. Each participant had studied between 500 and 1000 patients for thyroid function evaluation by performing T3, T4 and TSH radioimmunoassays. Each had also used the newly available supersensitive immunoradiometric (IRMA) assay in a group of patients to compare the efficiency of the new assay with that of the conventional assay. A microcomputer was provided to each participant for data analysis. Internal quality control was studied by establishing precision profiles and external quality control was on the basis of pooled standard sera in different ranges. Recommendation for the strategy suggested T4 RIA as the test of first choice in each category of thyroid function. IRMA TSH was suggested as a second test in borderline cases.
    Matched MeSH terms: Quality Control
  19. Fulltext Impact of pharmacist educational intervention on disease knowledge, rehabilitation and medication adherence, treatment-induced direct cost, health-related quality of life and satisfaction in patients with rheumatoid arthritis: study protocol for a randomized controlled trial
    Naqvi AA, Hassali MA, Naqvi SBS, Aftab MT
    Trials, 2019 Aug 09;20(1):488.
    PMID: 31399128 DOI: 10.1186/s13063-019-3540-z
    BACKGROUND: The objective of this study is to evaluate the effectiveness of pharmacist intervention in improving disease knowledge, adherence to treatment, health-related quality of life (HRQoL) and direct cost of treatment. The study also documents patient satisfaction with pharmacist counselling as a quality control measure.

    METHODS/DESIGN: This is a randomized, single-blind, two-arm, controlled trial in patients with rheumatoid arthritis visiting outpatient rheumatology clinics in Karachi, Pakistan. We will enroll patients with established diagnosis of rheumatoid arthritis over 3 months. The patients would be randomized through a computer-generated list into the control group, i.e., usual care or into the intervention group, i.e., pharmaceutical care, in a ratio of 1:1, after providing signed written consent. The study will take place in two patient-visits over the course of 3 months. Patients in the intervention group would receive intervention from the pharmacist while those in the control group will receive usual care. Primary outcomes include change in mean score from baseline (week 0) and at follow up (week 12) in disease knowledge, adherence to medications and rehabilitation/physical therapy. The secondary outcomes include change in the mean direct cost of treatment, HRQoL and patient satisfaction with pharmacist counselling.

    DISCUSSION: This is a novel study that evaluates the role of the pharmacist in improving treatment outcomes in patients with rheumatoid arthritis. The results of this trial could set the foundation for future delivery of care for this patient population in Pakistan. The results of this trial would be published in a peer-reviewed journal.

    TRIAL REGISTRATION: ClinicalTrials.gov, NCT03827148 . Registered on February 2019.

    Matched MeSH terms: Quality Control
  20. Fulltext Medicinal Plants in COVID-19: Potential and Limitations
    Lim XY, Teh BP, Tan TYC
    Front Pharmacol, 2021;12:611408.
    PMID: 33841143 DOI: 10.3389/fphar.2021.611408
    Currently, the search to identify treatments and vaccines for novel coronavirus disease (COVID-19) are ongoing. Desperation within the community, especially among the middle-and low-income groups acutely affected by the economic impact of forced lockdowns, has driven increased interest in exploring alternative choices of medicinal plant-based therapeutics. This is evident with the rise in unsubstantiated efficacy claims of these interventions circulating on social media. Based on enquiries received, our team of researchers was given the chance to produce evidence summaries evaluating the potential of complementary interventions in COVID-19 management. Here, we present and discuss the findings of four selected medicinal plants (Nigella sativa, Vernonia amygdalina, Azadirachta indica, Eurycoma longifolia), with reported antiviral, anti-inflammatory, and immunomodulatory effects that might be interesting for further investigation. Our findings showed that only A. indica reported positive antiviral evidence specific to the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) based on preliminary in silico data while all four medicinal plants demonstrated differential anti-inflammatory or immunomodulatory effects. The definitive roles of these medicinal plants in cytokine storms and post-infection complications remains to be further investigated. Quality control and standardisation of medicinal plant-based products also needs to be emphasized. However, given the unprecedented challenges faced, ethnopharmacological research should be given a fair amount of consideration for contribution in this pandemic.
    Matched MeSH terms: Quality Control
Related Terms
Filters
Contact Us

Please provide feedback to Administrator ([email protected])

External Links