A study was conducted in an oil palm plantation in Peninsular Malaysia to elucidate the effects of applying Magnesium Rich Synthetic Gypsum (MRSG), a by-product of chemical plant, on the chemical properties of soil, the uptake of heavy metals by the palm trees, the oil quality and its impact on the surrounding environment. The results showed that MRSG application onto soil cropped to oil palm could bring positive impact in terms of soil chemical properties and oil palm production. The quality of the oil was not significantly affected by the continuous MRSG application as shown by the low heavy metals and trace elements of concern content (Cu: 0.062 mg/kg; Fe: 2.10 mg/kg; Mn: 1.93 mg/kg; Pb: 0.006 mg/kg; Zn: 0.103 mg/kg; Cr: 0.354 mg/kg; Ni: 0.037 mg/kg). From the I-geochem index, the soil was found to have values ranging from -3.81 to -1.03 which is considered as uncontaminated. Further, its application did not result in negative impact on the surrounding environment; hence, the quality of the soil and surface water in the plantation and/or the surrounding area remained intact. Phytotoxic elements in the oil palm tissue (As: 0.12 mg/kg; Se: 0.05 mg/kg; Zn: 1.48 mg/kg; Ce: 0.47 mg/kg; La: 0.26 mg/kg; Sr: 3.03 mg/kg) and cytotoxic elements in the oil were below the acceptable limit. Based on the results of the Environmental Monitoring out during the period of the study, it was concluded that application of the by-product of the chemical plant as a source of Mg to enhance soil fertility in the oil palm plantation was considered safe and sustainable. The effects of applying MRSG and Chinese kieserite was almost similar. So, MRSG can be used as a possible source of Mg to replace Chinese kieserite for oil palm production on the Ultisols in Peninsular Malaysia.
This review emphasizes the role of toxic metal remediation approaches due to their broad sustainability and applicability. The rapid developmental processes can incorporate a large quantity of hazardous and unseen heavy metals in all the segments of the environment, including soil, water, air and plants. The released hazardous heavy metals (HHMs) entered into the food chain and biomagnified into living beings via food and vegetable consumption and originate potentially health-threatening effects. The physical and chemical remediation approaches are restricted and localized and, mainly applied to wastewater and soils and not the plant. The nanotechnological, biotechnological and genetical approaches required to more rectification and sustainability. A cellular, molecular and nano-level understanding of the pathways and reactions are responsible for potentially toxic metals (TMs) accumulation. These approaches can enable the development of crop varieties with highly reduced concentrations of TMs in their consumable foods and vegetables. As a critical analysis by authors observed that nanoparticles could provide very high adaptability for both in-situ and ex-situ remediation of hazardous heavy metals (HHMs) in the environment. These methods could be used for the improvement of the inbuilt genetic potential and phytoremediation ability of plants by developing transgenic. These biological processes involve the transfer of gene of interest, which plays a role in hazardous metal uptake, transport, stabilization, inactivation and accumulation to increased host tolerance. This review identified that use of nanoremediation and combined biotechnological and, transgenic could help to enhance phytoremediation efficiency in a sustainable way.
In this study geogenic radon potential (GRP) mapping was carried out on the bases of field radon in soil gas concentration and soil gas permeability measurements by considering the corresponding geological formations. The spatial pattern of soil gas radon concentration, soil permeability, and GRP and the relationship between geological formations and these parameters was studied by performing detailed spatial analysis. The radon activity concentration in soil gas ranged from 0.11 to 434.5 kBq m-3 with a mean of 18.96 kBq m-3, and a standard deviation was 55.38 kBq m-3. The soil gas permeability ranged from 5.2×10-14 to 5.2×10-12 m2, with a mean of 5.65×10-13 m2. The GRP values were computed from the 222Rn activity concentration and soil gas permeability data. The range of GRP values was from 0.04 to 154.08. Locations on igneous granite rock geology were characterized by higher soil radon gas activity and higher GRP, making them radon-prone areas according to international standards. The other study locations fall between the low to medium risk, except for areas with high soil permeability, which are not internationally classified as radon prone. A GRP map was created displaying radon-prone areas for the study location using Kriging/Cokriging, based on in situ and predicted measured values. The GRP map assists in human health risk assessment and risk reduction since it indicates the potential of the source of radon and can serve as a vital tool for radon combat planning.
Terrestrial radioactivity monitoring of 238U and 232Th series, and 40K in soil is an essential practice for radioactivity and radiation measurement of a place. In conventional practice, only basic data can be in-situ measured using a survey instrument, for example radioactivity concentration in soil and ambient dose equivalent rate. For other physical quantities, for example organ absorbed dose and organ equivalent dose, the measurement is impossible to be performed and can only be computed using Monte Carlo radiation transport simulations. In the past, most of the works only focused on calculating air-kerma-to-effective dose conversion factors. However, the information on organ dose conversion factors is scarcely documented and reported. This study was conducted to calculate organ absorbed and tissue-weighted equivalent dose conversion factors as a result of exposure from terrestrial gamma radiation. Series of organ dose conversion factors is produced based on computations from Monte Carlo MCNP5 simulations using modelled gamma irradiation geometry and established adult MIRD phantom. The study found out that most of the radiation exposed organs absorb energy at comparable rates, except for dense and superficial tissues i.e., skeleton and skin, which indicated slightly higher values. The good agreement between this work and previous studies demonstrated that our gamma irradiation geometry and modelling of gamma radiation sources are adequate. Therefore, the proposed organ dose conversion factors from this study are reasonably acceptable for dose estimation in environmental radioactivity monitoring practices.
The composition of heavy metals (and metalloid) in surface soils of iron ore mine-impacted areas has been evaluated of their potential ecological and human health risks. The mining areas included seven selected locations in the vicinity of active and abandoned iron ore-mining sites in Pahang, Malaysia. Heavy metals such as Fe, Mn, Cu, Zn, Co, Pb, Cr, Ni, and Cd and metalloid As were present in the mining soils of the studied area, while Cu was found exceeding the soil guideline value at all sampling locations. However, the assessment of the potential ecological risk index (RI) indicated low ecological risk (RI between 44 and 128) with respect to Cd, Pb, Cu, As, Zn, Co, and Ni in the surface soils. Contributions of potential ecological risk [Formula: see text]by metal elements to the total potential ecological RI were evident for Cd, As, Pb, and Cu. Contribution of Cu appears to be consistently greater in the abandoned mining area compared to active iron ore-mining site. For non-carcinogenic risk, no significant potential health risk was found to both children and adults as the hazard indices (HIs) were all below than 1. The lifetime cancer risk (LCR) indicated that As has greater potential carcinogenic risk compared to other metals that may induce carcinogenic effects such as Pb, Cr, and Cd, while the LCR of As for children fell within tolerable range for regulatory purposes. Irrespective of carcinogenic or non-carcinogenic risk, greater potential health risk was found among children (by an order of magnitude higher for most metals) compared to adults. The hazard quotient (HQ) and cancer risk indicated that the pathways for the risk to occur were found to be in the order of ingestion > dermal > inhalation. Overall, findings showed that some metals and metalloid were still present at comparable concentrations even long after cessation of the iron ore-mining activities.
Treatment of oil-contaminated soil is a major environmental concern worldwide. The aim of this study is to examine the applicability of a green solvent, ethyl lactate (EL), in desorption of diesel aliphatic fraction within total petroleum hydrocarbons (TPH) in contaminated soil and to determine the associated desorption kinetics. Batch desorption experiments were carried out on artificially contaminated soil at different EL solvent percentages (%). In analysing the diesel range of TPH, TPH was divided into three fractions and the effect of solvent extraction on each fraction was examined. The experimental results demonstrated that EL has a high and fast desorbing power. Pseudo-second order rate equation described the experimental desorption kinetics data well with correlation coefficient values, R (2), between 0.9219 and 0.9999. The effects of EL percentage, initial contamination level of soil and liquid to solid ratio (L/S (v/w)) on initial desorption rate have also been evaluated. The effective desorption performance of ethyl lactate shows its potential as a removal agent for remediation of TPH-contaminated soil worldwide.
This study was carried out to determine the concentration of (222)Rn, (226)Ra, and (238)U in 25 different toothpastes available in the local market in Penang, Malaysia, using a CR-39 detector. The results showed the maximum concentration of radon/ radium/uranium to be 4197.644 Bq.m(-3), 54.369 Bq.Kgm(-1), and 0.044 ppm in Colgate4; the annual effective dose was found (0.402 mSvy(-1)) in S07. The average concentration of radon (42 %, 3.224 KBq.m(-3)) was higher than the concentration of (214)Po, (218)Po in POS (32 %, 2.415 KBq.m(-3)) and POW (26 %, 1.979 KBq.m(-3)). Also the values of pH of samples ranged from 4.21 (highly acidic) in S04 to 9.97 (highly basic) in S07, with an average of 6.33 which tended towards an acidic behavior; a low or high pH for a long period of time can cause harmful side-effects and enamel erosion. Concentrations of heavy metals varied from the maximum value 56.156 ppm in the Ca elements in the Colgate 4 sample to a minimum value of -0.858 ppm in the Cd elements in Colgate 6 (Ca 56.156 ppm > Cd 51.572 ppm > Zn 41.039 ppm > Mg 11.682 ppm > Pb 11.009 ppm]. Monitoring the accumulation of these metals in toothpaste samples is very important: the average annual effective dose (0.3118 mSvy(-1)) was below the range (3-10 mSvy(-1)) reported by ICRP (1993), and therefore there is no evidence of health problems. Significant strong positive correlations were found (r = 1, Pearson correlation, p
Greenhouse experiments were carried out to determine the phytotoxic effects on the plant Ludwigia octovalvis in order to assess its applicability for phytoremediation gasoline-contaminated soils. Using plants to degrade hydrocarbons is a challenging task. In this study, different spiked concentrations of hydrocarbons in soil (1, 2, and 3 g/kg) were tested. The results showed that the mean efficiency of total petroleum hydrocarbon (TPH) removal over a 72-day culture period was rather high. The maximum removal of 79.8 % occurred for the 2 g/kg concentration, while the removal rate by the corresponding unplanted controls was only (48.6 %). The impact of gasoline on plants included visual symptoms of stress, yellowing, growth reduction, and perturbations in the developmental parameters. The dry weight and wet weight of the plant slightly increased upon exposure to gasoline until day 42. Scanning electron microscopy (SEM) indicated change to the root and stem structure in plant tissue due to the direct attachment with gasoline contaminated compared to the control sample. The population of living microorganisms in the contaminated soil was found to be able to adapt to different gasoline concentrations. The results showed that L. octovalvis and rhizobacteria in gasoline-contaminated soil have the potential to degrade organic pollutants.
Steady efforts in using ultrasonic energy to treat oil-contaminated sand started in the early 2000s until today, although pilot studies on the area can be traced to even earlier dates. Owing to the unique characteristics of the acoustic means, the separation of oil from sand has been showing good results in laboratories. This review provides the compilation of researches and insights into the mechanism of separation thus far. Related topics in the areas of oil-contaminated sand characterizations, fundamental ultrasonic cleaning, and cavitation effects are also addressed. Nevertheless, many of the documented works are only at laboratory or pilot-scale level, and the comprehensive interaction between ultrasonic parameters towards cleaning efficiencies may not have been fully unveiled. Gaps and opportunities are also presented at the end of this article.
Uranium, perhaps the most strategically important component of heavy minerals, finds particular significance in the nuclear industry. In prospecting trenches, the radioactivity of 238U and 232Th provides a good signature of the presence of heavy minerals. In the work herein, the activity concentrations of several key primordial radionuclides (238U, 232Th, and 40K) were measured in prospecting trenches (each of the latter being of approximately the same geometry and physical situation). All of these are located in the Seila area of the South Eastern desert of Egypt. A recently introduced industry standard, the portable hand-held RS-230 BGO gamma-ray spectrometer (1024 channels) was employed in the study. Based on the measured data, the trenches were classified as either non-regulated (U activity less than 1000 Bq kg-1) or regulated (with 238U activity more than 1000 Bq kg-1). Several radiological hazard parameters were calculated, statistical analysis also being performed to examine correlations between the origins of the radionuclides and their influence on the calculated values. While the radioactivity and hazard parameters exceed United Nations Scientific Committee on the Effects of Atomic Radiation (UNSCEAR) guided limits, the mean annual effective doses of 0.49 and 1.4 mSv y-1 in non-regulated and regulated trenches respectively remain well below the International Commission on Radiological Protection (ICRP) recommended 20 mSv/y maximum occupational limit. This investigation reveals that the studied area contains high uranium content, suitable for extraction of U-minerals for use in the nuclear fuel cycle.
Phytoremediation is an environmentally friendly alternative to traditional remediation technologies, notably for soil restoration and agricultural sustainability. This strategy makes use of marginal areas, incorporates biofortification processes, and expands crop alternatives. The ecological and economic benefits of phytoremediation are highlighted in this review. Native plant species provide cost-effective advantages and lower risks, while using invasive species to purify pollutants might be a potential solution to the dilemma of not removing them from the new habitat. Thus, strict management measures should be used to prevent the overgrowth of invasive species. The superior advantages of phytoremediation, including psychological and social improvements, make it a powerful tool for both successful cleanup and community well-being. Its ability to generate renewable biomass and adapt to a variety of uses strengthens its position in developing the bio-based economy. However, phytoremediation faces severe difficulties such as complex site circumstances and stakeholder doubts. Overcoming these challenges necessitates a comprehensive approach that balances economic viability, environmental protection, and community welfare. Incorporating regulatory standards such as ASTM and ISO demonstrates a commitment to long-term environmental sustainability, while also providing advice for unique nation-specific requirements. Finally, phytoremediation may contribute to a pleasant coexistence of human activity and the environment by navigating hurdles and embracing innovation.
This paper aims to review the applications of Fenton based treatments specifically for polycyclic aromatic hydrocarbons-contaminated soils. An overview of the background and principles of Fenton treatment catalysed by both homogenous (conventional and modified Fenton) and heterogeneous (Fenton-like) catalysts is firstly presented. Laboratory and field soil remediation studies are then discussed in terms of efficiency, kinetics and associated factors. Four main scopes of integrated Fenton treatments, i.e. physical-Fenton, biological-Fenton, electro-Fenton and photo-Fenton are also reviewed in this paper. For each of these integrated remediation technologies, the theoretical background and mechanisms are detailed alongside with achievable removal efficiencies for polycyclic aromatic hydrocarbons in contaminated soils compared to sole Fenton treatment. Finally, the environmental impacts of Fenton based soil treatments are documented and discussed.
Jiangxi red soil was used as the tested soil and water spinach (Ipomoea aquatic) and Chinese chive (Allium tuberosum) were used as the tested vegetables in this study to investigate the effects of different amounts of sewage-sludge application on the growth of vegetables and the migration and enrichment patterns of Cu and Zn in vegetables using the potted method. The results indicated that the application of sewage sludge could improve the properties of red soil and promote vegetable growth. The dry weight of water spinach and Chinese chive reached the maximal levels when treated with the amount of sewage sludge at 4% and 10%, which was 4.38 ± 0.82 g and 1.56 ± 0.31 g, respectively. The dry weights after the application of sewage sludge were all larger than control treatment (CK) without sludge application. With increases in the applied amount of sewage sludge, the concentrations of Cu and Zu in red soil continued to increase, and the peak value was not reached. After the two vegetables were planted, the concentrations of Cu and Zn in red soil decreased by different degrees. The degrees of decrease of Zn were generally higher than those of Cu. The enrichment coefficient of water spinach on Cu showed a trend of increase followed by a decrease and reached the peak value of 1.04 ± 0.38 when the applied amount was 4%. The enrichment coefficient of Chinese chive on Cu overall showed a decreasing trend and did not reach the peak value under the treatment levels used in this experiment. The enrichment pattern of Chinese chive on Zn was not obvious, and the differences among all treatment levels were not significant (p
The paper looks into the possibility of using standard addition method to analyse uranium and thorium in tin slag. Tin slag samples obtained from Butterworth was grind to 180 ȝm and injected with different concentrations of uranium and thorium. Linear calibration graphs were obtained for both these samples with R 2 values for uranium and thorium as 0.9989 and 0.9915 respectively. Based on this graphs, the initial uranium and thorium in the tin slag sample was established as 60 ppm for uranium and 160 ppm for thorium.
A diesel-degrading bacterium was isolated from a diesel-contaminated site in Selangor, Malaysia. The isolate was tentatively identified as Acinetobacter sp. strain DRY12 based on partial 16S rDNA molecular phylogeny and Biolog GN microplate panels and Microlog database. Optimum growth occurred from 3 to 5% diesel and the strain was able to tolerate as high as 8% diesel. The optimal pH that supported growth of the bacterium was between pH 7.5 to 8.0. The isolate exhibited optimal growth in between 30 and 35 degrees C. The best nitrogen source was potassium nitrate (between 0.6 and 0.9% (w/v)) followed by ammonium chloride, sodium nitrite and ammonium sulphate in descending order. An almost complete removal of diesel components was seen from the reduction in hydrocarbon peaks observed using Solid Phase Microextraction Gas Chromatography analysis after 10 days of incubation. The best growth kinetic model to fit experimental data was the Haldane model of substrate inhibiting growth with a correlation coefficient value of 0.97. The maximum growth rate- micromax was 0.039 hr(-1) while the saturation constant or half velocity constant Ks and inhibition constant Ki, were 0.387% and 4.46%, respectively. MATH assays showed that 75% of the bacterium was found in the hexadecane phase indicating that the bacterium was hydrophobic. The characteristics of this bacterium make it useful for bioremediation works in the Tropics.
The degradation behavior of veterinary antibiotics in soil is commonly studied using the following methods of adding antibiotics to the soil: (i) adding manure collected from animals fed with a diet containing antibiotics, (ii) adding antibiotic-free animal manure spiked with antibiotics and (iii) directly adding antibiotics. No research simultaneously comparing different antibiotic addition methods was found. Oxytetracycline (OTC) was used as a model antibiotic to compare the effect of the three commonly used antibiotic addition methods on OTC degradation behavior in soil. The three treatment methods have similar trends, though OTC degradation half-lives show the following significant differences (P<0.05): manure from swine fed OTC (treatment A)soil. Because the main entry route for veterinary antibiotics into soil is via the manure of animals given with antibiotics, the most appropriate method to study the degradation and ecotoxicity of antibiotic residues in soil may be to use manure from animals that are given a particular antibiotic, rather than by adding it directly to the soil.
This study aims to investigate the impacts of ethyl lactate (EL) based Fenton treatment on soil quality for polycyclic aromatic hydrocarbons (PAHs)-contaminated soils. Accumulation of oxygenated-polycyclic aromatic hydrocarbons (oxy-PAHs) was observed, but quantitative measurement on the most abundant compound 9,10-anthraquinone (ATQ) showed lower accumulation of the compound than that reported for ethanol (ET) based Fenton treatment. In general, as compared to conventional water (CW) based Fenton treatment, the EL based Fenton treatment exerted either a lower or higher negative impact on soil physicochemical properties depending on the property type and shared the main disadvantage of reduced soil pH. For revegetation, EL based Fenton treatment was most appropriately adopted for soil with native pH >/~ 6.2 in order to obtain a final soil pH >/~ 4.9 subject to the soil buffering capacity.
A white-rot fungus of Polyporus sp. S133 was isolated from an oil-polluted soil. The metabolism of pyrene by this fungus was investigated in liquid medium with 5 mg of the compound. Depletion of pyrene was evident during the 30-day growth period and was 21% and 90%, respectively, in cometabolism and metabolism of pyrene alone. Pyrene was absorbed to fungal cells or biodegraded to form simpler structural compounds. Seventy-one percent of eliminated pyrene was transformed by Polyporus sp. S133 into other compounds, whereas only 18% was absorbed in the fungal cell. The effects of pH and temperature on biomass production of Polyporus sp. S133 for pyrene were examined; the properties of laccase and 1,2-dioxygenase produced by Polyporus sp. S133 during pyrene degradation were investigated. The optimal values of pH were 3, 5, and 4 for laccase, 1,2-dioxygenase, and biomass production, respectively, whereas the optimal values of temperature were 25 °C for laccase and 50 °C for 1,2-dioxygenase and biomass production. Under optimal conditions, pyrene was mainly metabolized to 1-hydroxypyrene and gentisic acid. The structure of 1-hydroxypyrene and gentisic acid was determined by gas chromatography-mass spectrometry after identification using thin-layer chromatography.
This study describes the chemical speciation of Pb, Zn, Cu, Cr, As, and Sn in soil of former tin mining catchment. Total five sites were selected for sampling and subsequent subsamples were collected from each site in order to create a composite sample for analysis. Samples were analysed by the sequential extraction procedure using optical emission spectrometry (ICP OES). Small amounts of Cu, Cr, and As retrieved from the exchangeable phase, the ready available for biogeochemical cycles in the ecosystem. Low quantities of Cu and As could be taken up by plants in these kind of acidic soils. Zn not detected in the bioavailable forms while Pb is only present in negligible amounts in very few samples. The absence of mobile forms of Pb eliminates the toxic risk both in the trophic chain and its migration downwards the soil profile. The results also indicate that most of the metals have high abundance in residual fraction indicating lithogenic origin and low bioavailability of the metals in the studied soil. The average potential mobility for the metals giving the following order: Sn > Cu > Zn > Pb > Cr > As.
For decades Malaysia was the world's largest producer of Sn, but now the vast open cast mining operations have left a legacy of some 100,000 ha of what is effectively wasteland, covered with a mosaic of tailings and lagoons. Few plants naturally recolonise these areas. The demand for such land for both urban expansion and agricultural use has presented an urgent need for better characterisation. This study reports on the formation of artificial soils from alluvial Sn mining waste with a focus on the effects of experimental treatments on soil chemistry. Soil organic matter, clay, and pH were manipulated in a controlled environment. Adding both clay tailings and peat enhanced the cation exchange capacity of sand tailings but also reduced the pH. The addition of peat reduced the extractable levels of some elements but increased the availability of Ca and Mg, thus proving beneficial. The use of clay tailings increased the levels of macro and micronutrients but also released Al, As, La, Pb and U. Additionally, the effects of soil mix and mycorrhizal treatments on growth and foliar chemistry were studied. Two plant species were selected: Panicum milicaeum and Pueraria phaseoloides. Different growth patterns were observed with respect to the additions of peat and clay. The results for mycorrhizal treatment (live inoculum or sterile carrier medium) are more complex, but both resulted in improved growth. The use of mycorrhizal fungi could greatly enhance rehabilitation efforts on sand tailings.