The majority of patients with dysthyroid eye disease have an acquired colour vision defect. However, no psychophysical investigation of selective damage to colour or flicker pathways has been carried out. In order to clarify the nature of the visual pathology, we have used a psychophysical technique (spectral sensitivity) to selectively stimulate the chromatic and achromatic mechanisms. Spectral spots of size 1 degree presented at a rate of 1 Hz on a bright 1000 td white background are detected by the chromatic mechanism but a rate of 25 Hz reveals the achromatic mechanism. Fifteen patients (28 eyes) between the ages of 50-70 years were tested. The study showed that all patients had reduced spectral sensitivity, either 1 Hz, 25 Hz or both. The patients with reduced 1 Hz or 25 Hz spectral sensitivity only had a shorter systemic and ocular duration of the condition, had no proptosis, normal intraocular pressures in primary gaze, slightly higher intraocular pressures on upgaze, normal visual field plots and FM 100-Hue error scores higher than the normal age-matched values. The patients with reduced both 1 Hz and 25 Hz spectral sensitivities had a longer systemic and ocular duration of the condition, had proptosis, normal intraocular pressures in primary position, higher intraocular pressures on upgaze and higher FM 100-Hue error scores than the age-matched normals and those in Groups 1 and 2. A total of 50% of patients in Group 3 had defective visual field plots. These data suggest that there is a damage of the large achromatic fibres and small chromatic fibres in dysthyroid eye disease. The mechanism of the damage could be one of ischaemic or mechanical or both.
Nanoemulsions (NMs) are one of the most important colloidal dispersion systems that are primarily used to improve the solubility of poorly water soluble drugs. The main objectives of this study were, first, to prepare an NM loaded with fenofibrate using a high shear homogenization technique and, second, to study the effect of variable using a central composite design. Twenty batches of fenofibrate-loaded NM formulations were prepared. The formed NMs were subjected to droplet size analysis, zeta potential, entrapment efficiency, pH, dilution, polydispersity index, transmission electron microscopy (TEM), Fourier transform infrared spectrophotometry, differential scanning calorimetry (DSC), and in vitro drug release study. Analysis of variance was used for entrapment efficiency data to study the fitness and significance of the design. The NM-7 batch formulation demonstrated maximum entrapment efficiency (81.82%) with lowest droplet size (72.28 nm), and was thus chosen as the optimized batch. TEM analysis revealed that the NM was well dispersed with droplet sizes <100 nm. Incorporation of the drug into the NM was confirmed with DSC studies. In addition, the batch NM-7 also showed the maximum in vitro drug release (87.6%) in a 0.05 M sodium lauryl sulfate solution. The release data revealed that the NM followed first-order kinetics. The outcomes of the study revealed the development of a stable oral NM containing fenofibrate using the high shear homogenization technique. This approach may aid in further enhancing the oral bioavailability of fenofibrate, which requires further in vivo studies.
Trace elements play a significant role in giving nutritional benefits to the body because they act as essential cofactors for all physiological processes. However, there are some trace elements which may bring more harm than good when entering the human body. Due to its ability to incorporate trace elements in an amount that is proportional to an individual’s dietary intake and environmental exposure, human fingernails are suitable biomarkers in assessing the health status of an individual as they reflect on the trace element concentration present in the body. This study has analysed fingernail samples of 23 adult females residing in Kuching and Kota Samarahan, Sarawak, Malaysia for four elements, namely Cd, Cu, Pb and Zn. By using flame atomic absorption spectroscopy (FAAS), the mean elemental concentrations found in fingernail samples of research participants were 171.8 ± 33.8 μg/g for Zn, 27.8 ± 14.8 μg/g for Cu and 2.64 ± 0.94 μg/g for Pb. Cd concentrations were not able to be detected as they were below the detection limits. A standard reference material, NIST 1568b Rice Flour was used to verify the methods used in elemental analysis using FAAS. Independent t-test which was used to compare the means of Zn and Cu between vegetarians and non-vegetarians showed no significant differences for both elements. Moreover, correlation analysis showed negative correlations between Cu/Zn pair and Pb/Zn pair, whereas significant positive correlation was obtained for Cu/Pb pair. The overall data from this study showed good agreements with data obtained from studies in other countries. Therefore, the current data in this study represents the latest background elemental concentrations in fingernails of the residents in Kuching and Kota Samarahan, Sarawak.
Corn-cobs are an agro-industrial waste and composed of cellulose mostly. In this study cellulose was isolated from the waste corn-cobs and modified to polymeric hydroxamic acid palladium complex 1 and characterized by using a variety of spectroscopic methods such as field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy (EDX), transmission electron microscopy (TEM), X-ray powder diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and inductively coupled plasma atomic emission spectroscopy (ICP-AES). The complex 1 exhibited high catalytic activity towards Suzuki and Heck coupling reactions of activated and deactivated aryl halides to give the respective coupling products with high yield. Moreover, the complex 1 was recovered and recycled five times with no considerable loss of catalytic overall performance.
In this study, we have used aldehyde function of cinnamaldehyde to synthesize N, N'-Bis (cinnamaldehyde) ethylenediimine [C20H20N2] and Co(II) complex of the type [Co(C40H40N4)Cl2]. The structures of the synthesized compounds were determined on the basis of physiochemical analysis and spectroscopic data ((1)H NMR, FTIR, UV-visible and mass spectra) along with molar conductivity measurements. Anticandidal activity of cinnamaldehyde its ligand [L] and Co(II) complex was investigated by determining MIC80, time-kill kinetics, disc diffusion assay and ergosterol extraction and estimation assay. Ligand [L] and Co(II) complex are found to be 4.55 and 21.0 folds more efficient than cinnamaldehyde in a liquid medium. MIC80 of Co(II) complex correlated well with ergosterol inhibition suggesting ergosterol biosynthesis to be the primary site of action. In comparison to fluconazole, the test compounds showed limited toxicity against H9c2 rat cardiac myoblasts. In confocal microscopy propidium iodide (PI) penetrates the yeast cells when treated with MIC of metal complex, indicating a disruption of cell membrane that results in imbibition of dye. TEM analysis of metal complex treated cells exhibited notable alterations or damage to the cell membrane and the cell wall. The structural disorganization within the cell cytoplasm was noted. It was concluded that fungicidal activity of Co(II) complex originated from loss of membrane integrity and a decrease in ergosterol content is only one consequence of this.
A rapid and selective high-performance liquid chromatographic assay for determination of a new antimalarial drug (benflumetol, BFL) is described. After extraction with hexane-diethyl ether (70:30, v/v) from plasma, BFL was analysed using a C18 Partisil 10 ODS-3 reversed-phase stainless steel column and a mobile phase of acetonitrile-0.1 M ammonium acetate (90:10, v/v) adjusted to pH 4.9 with ultraviolet detection at 335 nm. The mean recovery of BFL over a concentration range of 50-400 ng/ml was 96.8 +/- 5.2%. The within-day and day-to-day coefficients of variation were 1.8-4.0 and 1.8-4.2%, respectively. The minimum detectable concentration in plasma for BFL was 5 ng/ml with a C.V. of less than 10%. This method was found to be suitable for clinical pharmacokinetic studies.
The interaction of tranilast (TRN), an antiallergic drug with the main drug transporter in human circulation, human serum albumin (HSA) was studied using isothermal titration calorimetry (ITC), fluorescence spectroscopy and in silico docking methods. ITC data revealed the binding constant and stoichiometry of binding as (3.21 ± 0.23) × 10(6)M(-1) and 0.80 ± 0.08, respectively, at 25°C. The values of the standard enthalpy change (ΔH°) and the standard entropy change (ΔS°) for the interaction were found as -25.2 ± 5.1 kJ mol(-1) and 46.9 ± 5.4 J mol(-1)K(-1), respectively. Both thermodynamic data and modeling results suggested the involvement of hydrogen bonding, hydrophobic and van der Waals forces in the complex formation. Three-dimensional fluorescence data of TRN-HSA complex demonstrated significant changes in the microenvironment around the protein fluorophores upon drug binding. Competitive drug displacement results as well as modeling data concluded the preferred binding site of TRN as Sudlow's site I on HSA.
Cancer and pathogenic microbial diseases have terribly affected human health over a longer period of time. In response to the increasing casualties due to cancer and microbial diseases, unique poly(3-methylthiophene) and poly(3-methylthiophene)-titanium(IV)phosphate composite were prepared via in-situ oxidative chemical polymerization in this work. The poly(3-methylthiophene) and poly(3-methylthiophene)-titanium(IV)phosphate composite were well characterized by Fourier transform infrared spectroscopy and field emission scanning electron microscopy. DNA binding studies by UV-Visible and fluorescence spectroscopic investigations indicated strong binding affinities of poly(3-methylthiophene) and poly(3-methylthiophene)-titanium(IV)phosphate nanocomposite; leading to structural damage of DNA. Poly(3-methylthiophene)-titanium(IV)phosphate nanocomposite showed stronger interactions with DNA as compared to poly(3-methylthiophene) and from dye displacement assay it was confirmed that mode of binding of both the formulations was intercalative. The antimicrobial screening revealed that polymer and its composite displayed stronger antibacterial effects than ampicillin against Bacillus subtilis, Staphylococcus aureus, Pseudomonas aeruginosa and Salmonella typhimurium. Besides, the poly(3-methylthiophene) and poly(3-methylthiophene)-titanium(IV)phosphate nanocomposite showed dose dependent effects towards estrogen receptor positive breast cancer (MCF-7) and estrogen receptor negative breast cancer (MDA-MB-231) cell lines; with poly(3-methylthiophene)-titanium(IV)phosphate nanocomposite showing better activities against both cell lines. In all in-vitro biological investigations, poly(3-methylthiophene)-titanium(IV)phosphate composite showed superior properties to that of the pure poly(3-methylthiophene), which encouraged us to suggest its potential as future therapeutic gear in drug delivery and other allied fields.
Ulam or traditional vegetables in Malaysia comprise more than 120 species representing various
families ranging from groundcovers, shrubs to trees. The leaves, shoots, flowers, fruits, roots and rhizomes of the vegetables are eaten fresh as salad or cooked and are consumed to add variety and flavor to the diet, as well as for their health benefits. Ulam species are rich in carbohydrate, protein, mineral and vitamin. This study established that ulam species differ greatly with respect to types and concentrations of carotenoids in leaves. A total of 10 species were evaluated for quantitative and qualitative carotenoid composition through spectrophotometry and HPLC analysis. The main carotenoids identified in these selected ulam were lutein, neoxanthin, violaxanthin, zeaxanthin and β-carotene. The ratio of these carotenoids varies between species.
The aim of the present study was to appraise the levels of heavy metal contamination (Zn and Pb) in sediment of the Langat River (Selangor, Malaysia). Samples were collected randomly from 15 sampling stations located along the Langat River. The parameters measured were pH, redox potential, salinity, electrical conductivity, loss of ignition, cation exchanges capacity (Na, Mg, Ca, K), and metal ions (Zn and Pb). The geo-accumulation index (I geo) and contamination factor (C f) were applied to determine and classify the magnitude of heavy metal pollution in this urban river sediment. Results revealed that the I geo of Pb indicated unpolluted to moderately polluted sediment at most of the sampling stations, whereas Zn was considered to be within background concentration. The I geo results were refined by the C f values, which showed Pb with very high C f at 12 stations. Zinc, on the other hand, had low to moderate C f values. These findings indicated that the sediment of the Langat River is severely polluted with Pb. The Zn concentration at most sampling points was well below most sediment quality guidelines. However, 40% of the sampling points were found to have a Pb concentration higher than the consensus-based probable effect concentration of 128 mg/kg (concentrations above this value are likely to cause harmful effects). This result not only highlights the severity of Pb pollution in the sediment of the Langat River, but also the potential risk it poses to the environment.
Mitochondrial DNA (mtDNA) is a hereditary material located in mitochondria and is normally maternally inherited. Mutational analysis performed on mtDNA proved that the mutations are closely related with a number of genetic illnesses, besides being exploitable for forensic identification. Those findings imply the importance of mtDNA in the scientific field. MtDNA can be found in abundance in tooth dentin where it is kept protected by the enamel, the hardest outer part of the tooth. In this study, two techniques of mtDNA extraction were compared to determine the efficacy between the two techniques. Teeth used for the study was collected from Dental Clinic, Hospital Universiti Sains Malaysia. After the removal of tooth from the tooth socket of the patient, the tooth was kept at -20C until use. Later, pulp tissue and enamel was excised using dental bur and only the root dentin was utilized for the isolation of mtDNA by crushing it mechanically into powdered form. MtDNA was extracted using the two published methods, Pfeifer and Budowle and then subjected to spectrophotometry DNA quantification and purity, Polymerase chain reaction (PCR) amplification of hypervariable-two region of mtDNA, followed by DNA sequencing to analyze the reliability of the extraction techniques. In conclusion, both techniques proved to be efficient and capable for the extraction of mtDNA from tooth dentin.
As many studies are exploring the association between ingestion of bioactive compounds and decreased risk of non-communicable diseases, the scientific community continues to show considerable interest in these compounds. In addition, as many non-nutrients with putative health benefits are reducing agents, hydrogen donors, singlet oxygen quenchers or metal chelators, measurement of antioxidant activity using in vitro assays has become very popular over recent decades. Measuring concentrations of total phenolics, flavonoids, and other compound (sub)classes using UV/Vis spectrophotometry offers a rapid chemical index, but chromatographic techniques are necessary to establish structure-activity. For bioactive purposes, in vivo models are required or, at the very least, methods that employ distinct mechanisms of action (i.e., single electron transfer, transition metal chelating ability, and hydrogen atom transfer). In this regard, better understanding and application of in vitro screening methods should help design of future research studies on 'bioactive compounds'.
Anoectochilus roxburghii (Wall.) Lindl. (Orchidaceae) is a precious traditional Chinese medicinal herb and has been perennially used to treat various illness. However, there were unethical sellers who adulterated wild A. roxburghii with tissue cultured and cultivated ones. Therefore, there is an urgent need for an effective authentication method to differentiate between these different types of A. roxburghii. In this research, the infrared spectroscopic tri-step identification approach including Fourier transform infrared spectroscopy (FT-IR), Second derivative infrared spectra (SD-IR) and two-dimensional correlation infrared spectra (2D-IR) was used to develop a simple and rapid method to discriminate between wild, cultivated and tissue cultivated A. roxburghii plant. Through this study, all three types of A. roxburghii plant were successfully identified and discriminated through the infrared spectroscopic tri-step identification method. Besides that, all the samples of wild, cultivated and tissue cultivated A. roxburghii plant were analysed with the Soft Independent Modelling of Class Analogy (SIMCA) pattern recognition technique to test and verify the experimental results. The results showed that the three types of A. roxburghii can be discriminated clearly as the recognition rate was 100% for all three types and the rejection rate was more than 60%. 70% of the validated samples were also identified correctly by the SIMCA model. The SIMCA model was also validated by comparing 70 standard herbs to the model. As a result, it was demonstrated that the macroscopic IR fingerprint method and the classification analysis could discriminate not only between the A. roxburghi samples and the standard herbs, it could also distinguish between the three different types of A. roxburghi plant in a direct, rapid and holistic manner.
Many wounds are unresponsive to currently available treatment techniques and therefore there is an immense need to explore suitable materials, including biomaterials, which could be considered as the crucial factor to accelerate the healing cascade. In this study, we fabricated polyhydroxyalkanoate-based antibacterial mats via an electrospinning technique. One-pot green synthesized graphene-decorated silver nanoparticles (GAg) were incorporated into the fibres of poly-3 hydroxybutarate-co-12 mol.% hydroxyhexanoate (P3HB-co-12 mol.% HHx), a co-polymer of the polyhydroxyalkanoate (PHA) family which is highly biocompatible, biodegradable, and flexible in nature. The synthesized PHA/GAg biomaterial has been characterized by field emission scanning electron microscopy (FESEM), elemental mapping, thermogravimetric analysis (TGA), UV-visible spectroscopy (UV-vis), and Fourier transform infrared spectroscopy (FTIR). An in vitro antibacterial analysis was performed to investigate the efficacy of PHA/GAg against gram-positive Staphylococcus aureus (S. aureus) strain 12,600 ATCC and gram-negative Escherichia coli (E. coli) strain 8739 ATCC. The results indicated that the PHA/GAg demonstrated significant reduction of S. aureus and E. coli as compared to bare PHA or PHA- reduced graphene oxide (rGO) in 2 h of time. The p value (p < 0.05) was obtained by using a two-sample t-test distribution.
A stability-indicating HPLC-UV method for the simultaneous determination of sildenafil citrate and dapoxetine hydrochloride in solution and tablet was developed. The mobile phase was comprised of acetonitrile and 0.2M ammonium acetate buffer. The analyte was eluted at 3.392min and 7.255min for sildenafil citrate and dapoxetine HCl respectively using gradient system at a flow rate of 1.5mL/min. The theoretical plates count was>2000, tailing factor
A developed colorimetric pH sensor film based on edible materials for real-time monitoring of food freshness is described. The mixed natural dyes from edible plants Clitoria sp and Brassica sp were extracted and incorporated into ι-carrageenan film as a colorimetric pH sensor film for monitoring food spoilage and its freshness. The color changes of the developed colorimetric sensor film were measured with chromametry and UV-vis spectroscopy, respectively. Experimental results show that colorimetric pH sensor film demonstrated statistically significant differences (p < 0.05) between CIE-L*a*b* coordinates color system indicated that the developed colorimetric sensor film was able to give a gradual change in color over a wide pH range. The color of the colorimetric sensor film also changes discretely and linearly with factors that contribute to food spoilage using shrimp and durian samples. Moreover, the developed colorimetric pH sensor film has the potential to be used as a safe, non-destructive testing and also a flexibly visual method for direct assessment of food freshness indicator during storage.
This paper provided comprehensive data on spectroscopic and antibacterial activities of thioureido compounds which are relevant with research article entitled "Synthesis, Spectroscopic Studies and Antibacterial Activity of New Lauroyl Thiourea Amino Acid Derivatives" [1]. Based on the reported study, four new thioureido derivatives, namely 3-(3-dodecanoyl-thioureido)propionic acid (R1), 2-(3-dodecanoyl-thioureido)-3-methyl butyric acid (R2), (3-dodecanoyl-thioureido)acetic acid (R3) and 2-(3-dodecanoyl-thioureido)-3-phenyl propionic acid (R4) were characterized by elemental analysis, Fourier Transform Infrared (FTIR), 1H Nuclear Magnetic Resonance (1H NMR) and 13C Nuclear Magnetic Resonance (13C NMR), and Ultraviolet Visible spectroscopy (UV-Vis). The preliminary results from antibacterial assay which were tested against Gram-positive bacteria such as Bacillus subtilis, Staphylococcus epidermidis, Staphylococcus aureus and Gram-negative bacteria such as Escherichia coli, Salmonella typhimurium are also described.
Three novel ruthenium(II) complexes of the general formula [Ru(II)(bpy)2
L]2+ were synthesized, where L =
1,10-phenanthroline derivatives of position 2 imidazole having 3,4-didecyloxy-phenyl (ddip), 3,4-ditetradecyloxy-phenyl
(dtip) and 3,4-dihexadecyloxy-phenyl (dhip). All complexes were characterized by elemental analysis, 1
H-NMR and ESI-MS.
Their photophysical properties have also been studied by UV-visible spectroscopy and fluorescence spectroscopy. The
complexes exhibit Ru(II) metal centered emission at approximately 610 nm in acetonitrile solution at room temperature. DNA
binding studies were carried out by UV-visible titration, luminescence titration and viscosity studies. The results indicated
that [Ru(bpy)2
(ddip)]2+ binds to CT-DNA by partial intercalation mode, while [Ru(bpy)2
(dtip)]2+ and [Ru(bpy)2
(dhip)]2+
bind intercalatively via extended ligands.
Novel biosensor architecture based on nanocrystalline cellulose (NCC)/CdS quantum dots (QDs) nanocomposite was developed for phenol determination. This nanocomposite was prepared with slight modification of nanocrystalline cellulose (NCC) with cationic surfactant of cetyltriammonium bromide (CTAB) and further decorated with 3-mercaptopropionic acid (3-MPA) capped CdS QDs. The nanocomposite material was then employed as scaffold for immobilization of tyrosinase enzyme (Tyr). The electrocatalytic response of Tyr/CTAB-NCC/QDs nanocomposite towards phenol was evaluated using differential pulse voltammetry (DPV). The current response obtained is proportional to the concentration of phenol which attributed to the reduction of o-quinone produced at the surface of the modified electrode. Under the optimal conditions, the biosensor exhibits good linearity towards phenol in the concentration range of 5-40 μM (R2 = 0.9904) with sensitivity and limit of detection (LOD) of 0.078 μA/μM and 0.082 μM, respectively.
Polymer-based nanocomposites have attracted a lot of attention for amperometric biosensor development due to their general physical and chemical properties including biocompatibility, film-forming ability, stability and different functional groups that can be bonded with other biomolecues. In this study, poly-4-vinlyridine homopolymer (P4VP) and polylactic acid-block-poly(2-vinylpyridine) block copolymer (PLA-b-P2VP) were used to hybridize with gold precursors (Au3+) based on the association between the nitrogen of the pyridine group of P4VP or P2VP block with gold precursors. P4VP/Au3+ and PLA-b-P2VP/Au3+ nanocomposites were prepared with ratio of gold to P2VP or P4VP (10:1). The Au3+ in both polymers was reduced to gold nanoparticles (AuNPs) via in-situ approach by using hydrazine. Fourier transform infrared spectroscopy (FTIR), ultraviolet-visible spectroscopy (UV-vis), transmission electron microscopy (TEM) and cyclic voltammetry (CV) were used to characterize the structural, morphological and electrochemical properties of the nanocomposites. The peak currents of P4VP/AuNPs and PLA-b-P2VP/AuNPs nanocomposites modified electrode were 6.685 nA and 69.432 nA, respectively, which are much lower than bare electrode (205.019 nA) due to the non-conductivity of P4VP and PLA-b-P2VP. In order to improve the electron transfer capability of electrode, graphene oxide (GO) was blended and electrochemically reduced to obtain P4VP/AuNPs/rGO and PLA-b-P2VP/AuNPs/rGO nanocomposites. After immobilization of these two nanocomposites on electrode through drop casting method, the peak currents of P4VP/AuNPs/rGO and PLA-b-P2VP/AuNPs/rGO nanocomposites modified electrode were 871.172 nA and 663.947 nA, respectively, which are much higher than bare electrode (205.019 nA) and shown good capability to accelerate electron transfer. Based on these characterizations, P4VP/AuNPs/rGO has potential as the nanocomposite to modify the electrode for enzymatic biosensor development.