Displaying publications 1 - 20 of 161 in total

Abstract:
Sort:
  1. Agung, E.H., Sapuan, S.M., Hamdan, M.M., Zaman, H.M.D.K., Mustofa, U.
    MyJurnal
    The properties of fibre-reinforced composites are dependent not only on the strength of the reinforcementfibre but also on the distribution of fibre strength and the composition of the chemicals or additivesaddition within the composites. In this study, the tensile properties of abaca fibre reinforced high impactpolystyrene (HIPS) composites, which had been produced with the parameters of fibre loading (30,40,50wt.%), coupling agent maleic anhydride (MAH) (1,2,3 wt%) and impact modifier (4,5,6 wt.%) weremeasured. The optimum amount of MAH is 3% and the impact modifier is 6% and these give the besttensile properties. Meanwhile, Differential Scanning Calorimetry (DSC) was used to study the thermalbehaviour within the optimum conditions of the composites. In this research, glass transitions temperature(Tg) of neat HIPS occurred below the Tg of the optimum condition of composites as the temperature ofan amorphous state. The endothermic peak of the composites was in the range of 430-4350C, includingneat HIPS. It was observed that enthalpy of the abaca fibre reinforced HIPS composites yielded belowthe neat HIPS of 748.79 J/g.
    Matched MeSH terms: Calorimetry, Differential Scanning
  2. Lim AW, Löbmann K, Grohganz H, Rades T, Chieng N
    J Pharm Pharmacol, 2016 Jan;68(1):36-45.
    PMID: 26663364 DOI: 10.1111/jphp.12494
    The objective was to characterize the structural behaviour of indomethacin-cimetidine and naproxen-cimetidine co-amorphous systems (1 : 1 molar ratio) prepared by quench cooling, co-evaporation and ball milling.
    Matched MeSH terms: Calorimetry, Differential Scanning
  3. Sergeev A, Shilkina N, Motyakin M, Barashkova I, Zaborova V, Kanina K, et al.
    Ultrason Sonochem, 2021 Oct;78:105751.
    PMID: 34534797 DOI: 10.1016/j.ultsonch.2021.105751
    Methods of NMR relaxation and differential scanning calorimetry (DSC) were used to study the crystallization of anhydrous milk fat (AMF) obtained from milk and subjected to ultrasonic (US) processing. Amongst the changes in the crystallization nature under the influence of ultrasound are the decrease in the crystallization temperature and the increase in the melting enthalpy of the anhydrous milk fat samples. The increase is ∼30% at 20 min of isothermal crystallization and is presumably explained by the additional formation of β'-form crystals from the melt. The parameters of the Avrami equation applied to the description of experimental data show an increase in the crystallization rate in samples with ultrasonic treatment and a change in the dimension of crystallization with a change in melting temperature.
    Matched MeSH terms: Calorimetry, Differential Scanning
  4. Dahimi O, Rahim AA, Abdulkarim SM, Hassan MS, Hashari SB, Mashitoh AS, et al.
    Food Chem, 2014 Sep 1;158:132-8.
    PMID: 24731324 DOI: 10.1016/j.foodchem.2014.02.087
    The adulteration of edible fats is a kind of fraud that impairs the physical and chemical features of the original lipid materials. It has been detected in various food, pharmaceutical and cosmeceutical products. Differential scanning calorimetry (DSC) is the robust thermo-analytical machine that permits to fingerprint the primary crystallisation of triacylglycerols (TAGs) molecules and their transition behaviours. The aims of this study was to assess the cross-contamination caused by lard concentration of 0.5-5% in the mixture systems containing beef tallow (BT) and chicken fat (CF) separately. TAGs species of pure and adulterated lipids in relation to their crystallisation and melting parameters were studied using principal components analysis (PCA). The results showed that by using the heating profiles the discrimination of LD from BT and CF was very clear even at low dose of less than 1%. Same observation was depicted from the crystallisation profiles of BT adulterated by LD doses ranging from 0.1% to 1% and from 2% to 5%, respectively. Furthermore, CF adulterated with LD did not exhibit clear changes on its crystallisation profiles. Consequently, DSC coupled with PCA is one of the techniques that might use to monitor and differentiate the minimum adulteration levels caused by LD in different animal fats.
    Matched MeSH terms: Calorimetry, Differential Scanning/methods*
  5. Zaliha O, Elina H, Sivaruby K, Norizzah AR, Marangoni AG
    J Oleo Sci, 2018 Jun 01;67(6):737-744.
    PMID: 29760328 DOI: 10.5650/jos.ess17168
    The in situ polymorphic forms and thermal transitions of refined, bleached and deodorized palm oil (RBDPO), palm stearin (RBDPS) and palm kernel oil (RBDPKO) were investigated using coupled X-ray diffraction (XRD) and differential scanning calorimetry (DSC). Results indicated that the DSC onset crystallisation temperature of RBDPO was at 22.6°C, with a single reflection at 4.2Å started to appear from 23.4 to 17.1°C, and were followed by two prominent exothermic peaks at 20.1°C and 8.5°C respectively. Further cooling to -40°C leads to the further formation of a β'polymorph. Upon heating, a of β'→βtransformation was observed between 32.1 to 40.8°C, before the sample was completely melted at 43.0°C. The crystallization onset temperature of RBDPS was 44.1°C, with the appearance of the α polymorph at the same temperature as the appearance of the first sharp DSC exothermic peak. This quickly changed from α→β´ in the range 25 to 21.7°C, along with the formation of a small β peak at -40°C. Upon heating, a small XRD peak for the β polymorph was observed between 32.2 to 36.0°C, becoming a mixture of (β´+ β) between 44.0 to 52.5°C. Only the β polymorph survived further heating to 59.8°C. For RBDPKO, the crystallization onset temperature was 11.6°C, with the formation of a single sharp exothermic peak at 6.5°C corresponding to the β' polymorphic form until the temperature reached -40°C. No transformation of the polymorphic form was observed during the melting process of RBDPKO, before being completely melted at 33.2°C. This work has demonstrated the detailed dynamics of polymorphic transformations of PKO and PS, two commercially important hardstocks used widely by industry and will contribute to a greater understanding of their crystallization and melting dynamics.
    Matched MeSH terms: Calorimetry, Differential Scanning*
  6. Tan CP, Man YC
    Phytochem Anal, 2002 May-Jun;13(3):129-41.
    PMID: 12099103
    The melting curves of 11 vegetable oils have been characterised. Vegetable oil samples that were cooled at a constant rate (5 degrees C/min) from the melt showed between one and seven melting endotherms upon heating at four different heating rates (1, 5, 10 and 20 degrees C/min) in a differential scanning calorimeter (DSC). Triacylglycerol (TAG) profiles and iodine value analyses were used to complement the DSC data. Generally, the melting transition temperature shifted to higher values with increased rates of heating. The breadth of the melting endotherm and the area under the melting peak also increased with increasing heating rate. Although the number of endothermic peaks was dependent on heating rate, the melting curves of the oil samples were not straightforward in that there was no correlation between the number of endothermic peaks and heating rates. Multiple melting behaviour in DSC experiments with different heating rates could be explained by: (1) the melting of TAG populations with different melting points; and (2) TAG crystal reorganisation effects. On the basis of the corollary results obtained, vegetable oils and fats may be distinguished from their offset-temperature (Toff) values in the DSC melting curves. The results showed that Toff values of all oil samples were significantly (p < 0.01) different in the melting curves scanned at four different scanning rates. These calorimetric results indicate that DSC is a valuable technique for studying vegetable oils.
    Matched MeSH terms: Calorimetry, Differential Scanning
  7. Nur Fadzilah Basri, Fauziah Abdul Aziz, Mohd Omar, A.K., Nik Norulaini, A.R.
    MyJurnal
    The main purpose of this study was to analyzed and examined the cocoa butter samples from Sabah. This work presence the crystal phases present in cocoa butter sample thus proved the existence of polymorphs obtained from differential scanning calorimeter (DSC) analysis and confirmed by X-ray diffraction (XRD). The cocoa butter samples were extracted using a conventional method by Soxhlet Extraction method. Crystals were formed under controlled static and tempered conditions. Cocoa butter polymorphism demonstrates that it is the actual crystallization temperature, not the cooling rate that determines the polymorph that crystallizes.
    Matched MeSH terms: Calorimetry, Differential Scanning
  8. Siti Rohana Ahmad, Salmah Husseinsyah, Kamarudin Hussin
    MyJurnal
    In this study, dynamic vulcanization process was used to improve the thermal properties of calcium carbonate filled composites. The composites were prepared using a Z-blade mixer at 180oC and rotor speed 50rpm. Thermogravimetric analysis (TGA) and Differential scanning calorimetry (DSC) techniques were used to analyze the thermal properties of the composites. The vulcanized and unvulcanized PP/EPDM composites were filled by CaCO3 at 0, 10, 20, 30, and 40 %wt. Meanwhile, thermogravimetric analysis indicates that the total weight loss of PP/EPDM/CaCO3 composites decreased with increasing filler loading. Dynamic vulcanized composites have higher thermal stability, while the crystallinity of PP/EPDM/CaCO3 composites were increased as compared to unvulcanized composites. Therefore, the thermal properties were improved by the presence of
    dynamic vulcanization process.
    Matched MeSH terms: Calorimetry, Differential Scanning
  9. Nurul, A.I., Azura, A.
    MyJurnal
    Knowledge about the thermal and storage behavior of produced protein is important for the purpose of storage, transport and shelve life during industrial application. Recombinant bromelain thermal and storage stability were measured and compared to the commercial bromelain using Differential Scanning Calorimetry (DSC). Recombinant bromelain is more stable than commercial bromelain at higher temperature but the stability was reduced after 7 days of storage at 4oC. Higher energy is needed to break the bond between amino acid chains in recombinant bromelain as shown by the enthalpy obtained, suggesting that recombinant bromelain has good protein structure and conformation compared to commercial.
    Matched MeSH terms: Calorimetry, Differential Scanning
  10. Siti Rohana Ahmad, Salmah Husseinsyah, Kamarudin Hussin
    MyJurnal
    A chemical modifier (acrylic acid) was used to improve the thermal properties of polypropylene/ ethylene propylene diene terpolymer/calcium carbonate (PP/EPDM/CaCO3) composites. Treated
    and untreated PP/EPDM composites were filled by CaCO3 at 0, 20 and 40% wt. The composites
    were prepared using Z-blade mixer machine at 180oC and 50 rpm of rotor speed. Thermogravimetric
    analysis (TGA) and differential scanning calorimetry (DSC) methods were used to analyze the thermal properties of the composites. Thermogravimetric analysis indicated that the total weight loss of PP/EPDM/CaCO3 composites decreased with the increasing filler loading for the treated and untreated composites. Meanwhile, the presence of acrylic acid was found to have increased the thermal stability and crystallinity of PP/EPDM/CaCO3
    .
    Matched MeSH terms: Calorimetry, Differential Scanning
  11. Rosdi, N.H., Mohd Kanafi, N., Abdul Rahman, N.
    MyJurnal
    Cellulose acetate (CA) is an interesting material due to its wide spectrum of utilities across different domains ranging from absorbent to membrane filters. In this study, polystyrene (PS) nanofibres, and cellulose acetate/polystyrene (CA/PS) blend nanofibres with various ratios of CA: PS from 20: 80 to 80: 20 were fabricated by using electrospinning technique. The SEM images show that the nanofibres exhibited non-uniform and random orientation with the average fibre diameter in the range of 100 to 800 nm. It was found that the incorporation of PS had a great effect on the morphology of nanofibre. At high proportion of PS, no or less beaded CA/PS nanofibres were formed. Thermal properties of the composite nanofibres were investigated by using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) techniques. The TGA results showed thermal stability of CA/PS nanofibres were higher than pristine CA.
    Matched MeSH terms: Calorimetry, Differential Scanning
  12. Sim, S.Y., Noor Aziah, A.A., Teng, T.T., Cheng, L.H.
    MyJurnal
    The effects of food gums addition on wheat dough freeze-thaw and frozen storage stability were studied. Thermal and dynamic mechanical properties of frozen wheat dough without yeast addition were
    determined by means of Differential Scanning Calorimetry (DSC) and Dynamic Mechanical Analysis (DMA).
    DSC results revealed that food gums showed the ability to increase freeze-thaw stability in frozen-stored
    samples wherein lower difference in melting enthalpy between first and second freeze-thaw cycle was shown. Based on DMA results, in general, difference between Tg’ and storage temperature (- 18°C) of dough became smaller upon addition of food gums. This may have a practical implication whereby the unfrozen phase could be better protected against physical degradation.
    Matched MeSH terms: Calorimetry, Differential Scanning
  13. Taharuddin NH, Jumaidin R, Mansor MR, Hazrati KZ, Hafila KZ, Md Yusof FA
    Int J Biol Macromol, 2024 Oct;277(Pt 1):133852.
    PMID: 39025171 DOI: 10.1016/j.ijbiomac.2024.133852
    The potential of Hylocereus polyrhizus peel (HPP) as a new eco-friendly reinforcement for thermoplastic sago starch/agar composite (TPSS/agar) was investigated. The integration of HPP into TPSS/agar composite aimed to enhance its mechanical and thermal characteristics. The study employed Fourier transform-infrared spectroscopy (FT-IR), Scanning electron microscopy (SEM), Thermogravimetric analysis (TGA), and Differential Scanning Calorimetry (DSC), as well as mechanical, physical properties and soil burial testing to analyse the composites. The results showed a favourable miscibility between the matrix and filler, while at higher concentrations of HPP, the starch granules became more visible. The tensile and impact properties of the composites improved significantly after incorporating HPP at 20 wt%, with values of 12.73 MPa and 1.87 kJ/m2, respectively. The glass transition temperature (Tg) and initial decomposition temperature (Ton) decreased with the addition of HPP. The density of the composites reduced from 1.51 ± 0.01 to 1.26 ± 0.01 g/cm3 as the HPP amount increased. The environmental properties indicated that the composites can be composted, with weight loss accelerating from 35 to 60 % and 61 to 91 % by the addition of HPP in 2- and 4-weeks' time, respectively. The study demonstrates the potential of TPSS/agar/HPP composites as eco-friendly materials for various applications.
    Matched MeSH terms: Calorimetry, Differential Scanning
  14. Dua K, Pabreja K, Ramana MV, Lather V
    J Pharm Bioallied Sci, 2011 Jul;3(3):417-25.
    PMID: 21966164 DOI: 10.4103/0975-7406.84457
    The objective of the present investigation was to study the effect of β-cyclodextrin (β-CD) on the in vitro dissolution of aceclofenac (AF) from molecular inclusion complexes. Aceclofenac molecular inclusion complexes in 1:1 and 1:2 M ratio were prepared using a kneading method. The in vitro dissolution of pure drug, physical mixtures, and cyclodextrin inclusion complexes was carried out. Molecular inclusion complexes of AF with β-CD showed a considerable increase in the dissolution rate in comparison with the physical mixture and pure drug in 0.1 N HCl, pH 1.2, and phosphate buffer, pH 7.4. Inclusion complexes with a 1:2 M ratio showed the maximum dissolution rate in comparison to other ratios. Fourier transform infrared spectroscopy and differential scanning calorimetry studies indicated no interaction between AF and β-CD in complexes in solid state. Molecular modeling results indicated the relative energetic stability of the β-CD dimer-AF complex as compared to β-CD monomer-AF. Dissolution enhancement was attributed to the formation of water soluble inclusion complexes with β-CD. The in vitro release from all the formulations was best described by first-order kinetics (R(2) = 0.9826 and 0.9938 in 0.1 N HCl and phosphate buffer, respectively) followed by the Higuchi release model (R(2) = 0.9542 and 0.9686 in 0.1 N HCl and phosphate buffer, respectively). In conclusion, the dissolution of AF can be enhanced by the use of a hydrophilic carrier like β-CD.
    Matched MeSH terms: Calorimetry, Differential Scanning
  15. Woo HJ, Arof AK
    PMID: 26945998 DOI: 10.1016/j.saa.2016.02.034
    A flexible solid polymer electrolyte (SPE) system based on poly(ε-caprolactone) (PCL), a FDA approved non-toxic and biodegradable material in the effort to lower environmental impact was prepared. Ammonium thiocyanate (NH4SCN) and ethylene carbonate (EC) were incorporated as the source of charge carriers and plasticizing agent, respectively. When 50wt.% of ethylene carbonate (EC) was added to PCL-NH4SCN system, the conductivity increased by two orders from of 3.94×10(-7)Scm(-1) to 3.82×10(-5)Scm(-1). Molecular vibrational analysis via infrared spectroscopy had been carried out to study the interaction between EC, PCL and NH4SCN. The relative percentage of free ions, ion pairs and ion aggregates was calculated quantitatively by deconvoluting the SCN(-) stretching mode (2030-2090cm(-1)). This study provides fundamental insight on how EC influences the free ion dissociation rate and ion mobility. The findings are also in good agreement to conductivity, differential scanning calorimetry and X-ray diffraction results. High dielectric constant value (89.8) of EC had made it an effective ion dissociation agent to dissociate both ion pairs and ion aggregates, thus contributing to higher number density of free ions. The incorporation of EC had made the polymer chains more flexible in expanding amorphous domain. This will facilitate the coupling synergy between ionic motion and polymer segmental motion. Possible new pathway through EC-NH4(+) complex sites for ions to migrate with shorter distance has been anticipated. This implies an easier ion migration route from one complex site to another.
    Matched MeSH terms: Calorimetry, Differential Scanning
  16. Che Man YB, Tan CP
    Phytochem Anal, 2002 May-Jun;13(3):142-51.
    PMID: 12099104
    The effects of scanning rates (1, 5, 10 and 20 degrees C/min) on the DSC cooling profiles of 11 vegetable oils have been determined in order to monitor peak transition temperatures, onset temperatures and crystallisation enthalpies. Triacylglycerol (TAG) profiles and iodine value analyses were used to complement the DSC data. The melted samples exhibited complicated crystallising exotherms. As the cooling rate increased, the crystallisation temperature decreased and the breadth of the crystallisation exotherm on cooling from the melt increased. In addition, the intensity of the exothermic peak increased somewhat when the cooling rate was increased. At slow cooling rates, TAG had more time to interact. It is conceivable that, at a low cooling rate (1 degree C/min), a prominent exotherm would be observed on crystallisation of vegetable oils and fats. The occurrence of one exotherm upon cooling indicated the co-crystallisation of the TAG upon slow cooling. On the basis of the corollary results obtained, vegetable oils may be differentiated by their onset temperature (Ton) values in the DSC cooling curves. Generally, there was a shift of Ton toward lower values with increasing cooling rates.
    Matched MeSH terms: Calorimetry, Differential Scanning
  17. Jesuarockiam N, Jawaid M, Zainudin ES, Thariq Hameed Sultan M, Yahaya R
    Polymers (Basel), 2019 Jun 26;11(7).
    PMID: 31247898 DOI: 10.3390/polym11071085
    The aim of the present research work is to enhance the thermal and dynamic mechanical properties of Kevlar/Cocos nucifera sheath (CS)/epoxy composites with graphene nano platelets (GNP). Laminates were fabricated through the hand lay-up method followed by hot pressing. GNP at different wt.% (0.25, 0.5, and 0.75) were incorporated with epoxy resin through ultra-sonication. Kevlar/CS composites with different weight ratios (100/0, 75/25, 50/50, 25/75, 0/100) were fabricated while maintaining a fiber/matrix weight ratio at 45/55. Thermal degradation and viscoelastic properties were evaluated using thermogravimetric analysys (TGA), differential scanning calorimetric (DSC) analysis, and a dynamic mechanical analyser (DMA). The obtained results revealed that Kevlar/CS (25/75) hybrid composites at 0.75 wt.% of GNP exhibited similar thermal stability compared to Kevlar/epoxy (100/0) composites at 0 wt.% of GNP. It has been corroborated with DSC observation that GNP act as a thermal barrier. However, DMA results showed that the Kevlar/CS (50/50) hybrid composites at 0.75 wt.% of GNP exhibited almost equal viscoelastic properties compared to Kevlar/epoxy (100/0) composites at 0 wt.% GNP due to effective crosslinking, which improves the stress transfer rate. Hence, this research proved that Kevlar can be efficiently (50%) replaced with CS at an optimal GNP loading for structural applications.
    Matched MeSH terms: Calorimetry, Differential Scanning
  18. Singh R, Singh G, Singh J, Kumar R, Rahman MM, Ramakrishna S
    Proc Inst Mech Eng H, 2019 Nov;233(11):1196-1203.
    PMID: 31545132 DOI: 10.1177/0954411919877979
    In this experimental study, a composite of poly-ether-ketone-ketone by reinforcement of hydroxyapatite and chitosan has been prepared for possible applications as orthopaedic scaffolds. Initially, different weight percentages of hydroxyapatite and chitosan were reinforced in the poly-ether-ketone-ketone matrix and tested for melt flow index in order to check the flowability of different compositions/proportions. Suitable compositions revealed by the melt flow index test were then taken forward for the extrusion of filament required for fused deposition modelling. For thermomechanical investigations, Taguchi-based design of experiments has been used with input variables in the extrusion process as follows: temperature, load applied and different composition/proportions. The specimens in the form of feedstock filament produced by the extrusion process were made to undergo tensile testing. The specimens were also inspected by differential scanning calorimetry and photomicrographs. Finally, the specimen showing the best performance from the thermomechanical viewpoint has been selected to extrude the filament for the fused deposition modelling process.
    Matched MeSH terms: Calorimetry, Differential Scanning
  19. Awang N, Jaafar J, Ismail AF
    Polymers (Basel), 2018 Feb 15;10(2).
    PMID: 30966230 DOI: 10.3390/polym10020194
    Void-free electrospun SPEEK/Cloisite15A® densed (SP/e-spunCL) membranes are prepared. Different loadings of Cloisite15A® (0.10, 0.15, 0.20, 0.25 and 0.30 wt %) are incorporated into electrospun fibers. The physico-chemical characteristics (methanol permeability, water uptake and proton conductivity) of the membranes are observed. Thermal stability of all membranes is observed using Thermal Gravimetry Analysis (TGA). The thrree stages of degradation range between 163.1 and 613.1 °C. Differential Scanning Calorimetry (DSC) is used to study the wettability of the membranes. SP/e-spunCL15 shows the lowest freezing bound water of 15.27%, which contributed to the lowest methanol permeability. The non-freezing bound water that proportionally increased with proton conductivity of SP/e-spunCL15 membrane is the highest, 10.60%. It is suggested that the electrospinning as the fabricating method has successfully exfoliated the Cloisite in the membrane surface structure, contributing to the decrease of methanol permeability, while the retained water has led to the enhancement of proton conductivity. This new fabrication method of SP/e-spunCL membrane is said to be a desirable polymer electrolyte membrane for future application in direct methanol fuel cell field.
    Matched MeSH terms: Calorimetry, Differential Scanning
  20. Haniffa MACM, Ching YC, Chuah CH, Kuan YC, Liu DS, Liou NS
    Polymers (Basel), 2017 May 01;9(5).
    PMID: 30970841 DOI: 10.3390/polym9050162
    Non-isocyanate polyurethane (NIPU) was prepared from Jatropha curcas oil (JCO) and its alkyd resin via curing with different diamines. The isocyanate-free approach is a green chemistry route, wherein carbon dioxide conversion plays a major role in NIPU preparation. Catalytic carbon dioxide fixation can be achieved through carbonation of epoxidized derivatives of JCO. In this study, 1,3-diaminopropane (DM) and isophorone diamine (IPDA) were used as curing agents separately. Cyclic carbonate conversion was catalyzed by tetrabutylammonium bromide. After epoxy conversion, carbonated JCO (CJCO) and carbonated alkyd resin (CC-AR) with carbonate contents of 24.9 and 20.2 wt %, respectively, were obtained. The molecular weight of CJCO and CC-AR were determined by gel permeation chromatography. JCO carbonates were cured with different amine contents. CJCO was blended with different weight ratios of CC-AR to improve its characteristics. The cured NIPU film was characterized by spectroscopic techniques, differential scanning calorimetry, and a universal testing machine. Field emission scanning electron microscopy was used to analyze the morphology of the NIPU film before and after solvent treatment. The solvent effects on the NIPU film interfacial surface were investigated with water, 30% ethanol, methyl ethyl ketone, 10% HCl, 10% NaCl, and 5% NaOH. NIPU based on CCJO and CC-AR (ratio of 1:3) with IPDA crosslink exhibits high glass transition temperature (44 °C), better solvent and chemical resistance, and Young's modulus (680 MPa) compared with the blend crosslinked with DM. Thus, this study showed that the presence of CC-AR in CJCO-based NIPU can improve the thermomechanical and chemical resistance performance of the NIPU film via a green technology approach.
    Matched MeSH terms: Calorimetry, Differential Scanning
Filters
Contact Us

Please provide feedback to Administrator ([email protected])

External Links